1、AEROSPACE STANDARD NUT, FLOATING, SELF-LOCKING, ATTACHED RETENTION ELEMENT, 450 F, 125 KSI FTU, UNS S66286 AS3601Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,
2、mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-12REA
3、FFIRMED 2006-05 REVISED 2013-08THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5310 AS3601SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse
4、ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, or
5、cancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3601ARATIONALE UPDATE THREAD SPECIFICATION TO AS8879, UPDATE MARKING NOTE, DELETE DUPLICATE REQUIREMENTS INCLUDED ON AS3
6、602, FIGURE 1 REDRAWN, AND REFERENCES UPDATED AND CORRECTED. FIGURE 1 - NUT ASSEMBLY AEROSPACE STANDARD AS3601SHEET 2 OF 2REV. ANUT, FLOATING, SELF-LOCKING, ATTACHED RETENTION ELEMENT, 450 F, 125 KSI FTU, UNS S66286 TABLE 1A - PART NUMBERS AND DIMENSIONS T, A, B, C, D, E, AND G PARTNUMBER TTHREADAMA
7、X B C MIND MIN E G AS3601-01 .1900-32 UNJF-3B .405 .415-.435 .235 .270 .296-.304 .177-.197AS3601-02 .1900-32 UNJF-3B .405 .415-.435 .235 .270 .296-.304 .177-.197AS3601-03 .2500-28 UNJF-3B .465 .486-.506 .300 .335 .363-.369 .188-.208AS3601-04 .2500-28 UNJF-3B .465 .486-.506 .300 .335 .363-.369 .188-.
8、208TABLE 1B - DIMENSIONS H, J, K, L, M, N, V, AND GRIP LENGTH PARTNUMBER HMAX J (K) L MMAX N V RECOMMENDED GRIP LENGTH AS3601-01 .270 .065-.085 .068 .084-.114 .587 .023-.030 .025-.035 .031-.062 AS3601-02 .270 .065-.085 .068 .115-.145 .587 .053-.060 .025-.035 .063-.094 AS3601-03 .325 .073-.093 .089 .
9、084-.114 .665 .023-.030 .035-.045 .031-.062 AS3601-04 .325 .073-.093 .089 .115-.145 .665 .053-.060 .035-.045 .063-.094 NOTES: 1. MATERIAL: NUT - SEE AS3602 (UNS S66286) SLEEVE - AMS5639 (UNS S30400) OR AMS5514 (UNS S30500) CAGE - AMS5528 (UNS S17700) 2. HEAT TREATMENT: NUT - SEE AS3602 CAGE - AGED T
10、O 38 HRC MIN 3. FINISH: NUT - SEE AS3602 SLEEVE AND CAGE - PASSIVATE PER AMS2700. 4. PERFORMANCE FOR FLARABILITY, PUSH OUT AND TORQUE OUT PER AS7251. 5. RADIAL FLOAT TO BE .020 MIN. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE
11、125 MICROINCHES Ra. 7. THE NUT ELEMENT SHALL BE REMOVABLE FROM THE CAGE WITH THE MANUFACTURERS RECOMMENDED REMOVAL TOOL AND A NEW NUT ELEMENT (AS3602) SHALL BE CAPABLE OF BEING SNAPPED INTO THE CAGE. 8. THE CAGE SHALL BE CAPABLE OF BEING REUSED A MINIMUM OF 5 TIMES FOR THE REPLACEMENT OF THE NUT ELE
12、MENT (AS3602). THE NUT SHALL THEN MEET THE TORQUE OUT AND PUSH OUT VALUES OF AS7251. 9. REMOVE BURRS AND SHARP EDGES. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 11. DIMENSIONS ARE IN INCHES. 12. DO NOT USE UNASSIGNED PART NUMBERS. 13. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE C
13、ONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
