1、 AEROSPACE STANDARD FITTING, ADAPTER, HOSE TO STRAIGHT PIPE AS5183Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwi
2、se, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REAFFIRMED2015-04THIRD ANGLE PROJECTION CUSTODIAN:
3、 G-3/G-3B FEDERAL SUPPLY CLASS 4730AS5183 SHEET 1 OF 4 PROCUREMENT SPECIFICATION: AS4843/2 /4/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and sui
4、tability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE val
5、ues your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5183 RATIONALE AS5183 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - FITTING, ADAPTERAEROSPACE STANDARD AS5183 SHEET 2 OF 4 FITTING, ADAPTER, HOSE TO STRA
6、IGHT PIPE TABLE 1A - DIMENSIONSBASIC NO.AS5183/14/SIZE CODE(NOMINALTUBE SIZE)PORT#1(NOMINALPIPE SIZE)PORT#2T THREADPERMIL-P-7105ANPTA.031B.010 C D E F0402 .250 .188 1/8-27 2.078 .418 .188 .187 0604 .375 .250 1/4-18 2.344 .605 .282 .297 1.6250806 .500 .375 3/8-18 2.375 .730 .406 .406 1006 .625 .375 3
7、/8-18 2.375 .855 .406 .500 1.6251008 .625 .500 1/2-14 2.578 .918 .532 .500 .906 1206 .750 .375 3/8-18 2.406 .980 .406 .625 1.6251212 .750 .750 3/4-14 2.625 1.103 .720 .625 .922 1606 1.000 .375 3/8-18 2.625 1.228 .406 .845 1.6251612 1.000 .750 3/4-14 2.625 1.228 .720 .845 1.6251616 1.000 1.000 1-11.5
8、 2.844 1.353 .940 .845 1.109 2016 1.250 1.000 1-11.5 2.875 1.428 .940 1.096 1.6252020 1.250 1.250 1-1/4-11.5 2.891 1.728 1.253 1.096 1.141 2420 1.500 1.250 1-1/4-11.5 2.906 1.728 1.253 1.346 1.6252424 1.500 1.500 1-1/2-11.5 2.938 1.978 1.503 1.346 1.156 TABLE 1B - WEIGHTSBASIC NO.AS5183/14/SIZE CODE
9、 HLB/EAMAXALLB/EAMAXCULB/EAMAXSTEEL0402 .428- .440 .0113 .0344 .03250604 .615- .628 .0245 .0744 .07030806 .740- .753 .0353 .107 .1011006 .865- .878 .0430 .131 .1231008 .928- .941 .0602 .183 .1731206 .990-1.003 .0561 .171 .1611212 1.113-1.128 .0885 .269 .2541606 1.238-1.253 .111 .336 .3171612 1.238-1
10、253 .0874 .266 .2511616 1.363-1.380 .144 .436 .4122016 1.438-1.505 .163 .495 .4672020 1.738-1.755 .230 .700 .6612420 1.738-1.755 .210 .638 .6032424 1.988-2.005 .294 .893 .843AEROSPACE STANDARD AS5183 SHEET 3 OF 4 FITTING, ADAPTER, HOSE TO STRAIGHT PIPE NOTES:/1/ MATERIAL:a. DASH AS CODE LETTER - TY
11、PE 1137 CARBON STEEL BAR PER ASTM A 108 OR TYPE 4130 PER MIL-S-6758 OR AMS 6370 OR TYPE 4140 PER MIL-S-5626 OR AMS 6382. /2/b. CODE LETTER B - TYPE 360 COPPER ALLOY BAR PER ASTM B 16, ASTM B 138, OR AMS 4610.c. CODE LETTER D - TYPE 2024-T6 ALUMINUM ALLOY BAR PER QQ-A-225/6 OR AMS 4112 OR TYPE 2024-T
12、851 ALUMINUM ALLOY BAR PER QQ-A-225/6.d. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER QQ-S-763 OR AMS 5639.e. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER QQ-S-763 OR AMS 5648.f. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL BAR PER QQ-S-763 OR AMS 5645.g. CODE LETTE
13、R W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124./2/ HEAT TREATMENT:a. DASH AS CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.b. OTHER CODE LETTERS - NONE.3. FINISH:a. DASH AS CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE
14、 II, CLASS 2 AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION.b. CODE LETTER B - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 3 OR NONE.c. CODE LETTER D - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION.d. CODE LETTERS J, K, AND R - PASSIVAT
15、E PER QQ-P-35, TYPE VI OR VII.e. CODE LETTER W - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION./4/ PROCUREMENT SPECIFICATION: AS4843/2 EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE AS
16、SEMBLY AS APPLICABLE. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B.a. SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK,
17、LETTER “AS” AND MATERIAL CODE LETTER.b. SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER.6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH A MAXIMUM OPERATING PRESSURE OF 600 psi. THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF AN8
18、40 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD./7/ THE INTERNAL DIAMETERS C AND D SHALL END IN A CONICAL END OF 110 MINIMUM INCLUDED ANGLE./8/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942.9. INTERPRETATION OF DRAWING PER ARP4296.10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS
19、PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra.11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 030.AEROSPACE STANDARD AS5183 SHEET 4 OF 4 FITTING, ADAPTER, HOSE TO STRAIGHT PIPE NOTES (CONTINUED):/14/
