1、 AEROSPACE STANDARD REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A AS81969/27Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mecha
2、nical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2015-06THIRD AN
3、GLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/27 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary,
4、 andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomm
5、ents andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/27 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/27 WITH THIS DOCUMENT, TO IMPROVE DRA
6、WING LEGIBILITY, TO UPDATE QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - REMOVAL TOOL CONFIGURATIONS/DIMENSIONS A
7、EROSPACE STANDARD AS81969/27 SHEET 2 OF 2 REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A TABLE 1 - FIGURE 1 DIMENSIONS/SUPERSEDED PART NUMBERS DASH NUMBER WIRE BARREL SIZE A .016 (0.41) B DIA. .016 (0.41) C .016 (0.41) D DIA. +.002/-.000 (0.05/0.00) E DIA. +.000/-.002
8、0.00/-.0.05)F DIA. -.000/+.002 (-0.00/+0.05)G RAD. .031 (0.79) SUPERSEDED PART NUMBER -01 4/0 2.500 (63.50) 1.250 (31.75) .500 (12.70) .753 (19.13) .790 (20.07) .772 (19.61) .062 (1.57) MS90562-1 -02 2/0 1.125 (28.58) .659 (16.74) .696 (17.68) .678 (17.22) MS90562-2 -03 1/0 1.000 (25.40) .521 (13.
9、23) .558 (14.17) .540 (13.72) MS90562-3 -04 2 .938 (23.83) .425 (10.80) .462 (11.73) .444 (11.28) MS90562-4 -05 4 .875 (22.22) .339 (8.61) .376 (9.55) .358 (9.09) MS90562-5 -06 6 .812 (20.62) .317 (8.05) .354 (8.99) .336 (8.53) MS90562-6 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT
10、AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .
11、010 INCH (0.25 MILLIMETERS) FOR DECIMALS AND 2 FOR ANGLES. CONCENTRICITY IS .004 INCH (0.10 MILLIMETERS) TIR (RFS). 2. MATERIAL AND FINISHES: MATERIAL - CORROSION RESISTANT STEEL PER AMS-QQ-S-763, CLASS 303, CONDITION A. FINISH - NOT APPLICABLE. 3. PART NUMBER/MARKING: SEE EXAMPLE BELOW: M81969 /27
12、01 BASE SPECIFICATION DETAIL SHEET DASH NUMBER (SEE TABLE 1) EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. QUALIFICATION SHAL
13、L BE PERFORMED IN ACCORDANCE WITH AS81969. HOWEVER, ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALI
14、FICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO REMOVE AS39029/48 AND /49 CONTACTS FROM CONNECTORS SPECIFIED IN MIL-DTL-22992. 2. THIS DOCUMENT SUPERSEDES MS90562D DATED 6 JUNE 1980 AND MIL-I-81969/27 DATED 11 JANUARY 1979. SPECIF
15、ICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
