1、 AEROSPACE STANDARD BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC MA3513Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect
2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 199
3、3-09REAFFIRMED 2013-10THIRD ANGLE PROJECTION CUSTODIAN: E-25 FEDERAL SUPPLY CLASS 5306 MA3513 SHEET 1 OF 10 PROCUREMENT SPECIFICATION: MA3378SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report i
4、s entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE
5、invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA3513 RATIONALE MA3513 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 AEROSPACE STANDARD MA3513 SHEET 2 OF
6、 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 1 - DIMENSIONSAEROSPACE STANDARD MA3513 SHEET 3 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONSAEROSPACE STAND
7、ARD MA3513 SHEET 4 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD MA3513 SHEET 5 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TA
8、BLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD MA3513 SHEET 6 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD MA3513 SHEET 7 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED,
9、 WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD MA3513 SHEET 8 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD M
10、A3513 SHEET 9 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC TABLE 2 - SHANK LENGTH DIMENSIONS (CONTINUED)AEROSPACE STANDARD MA3513 SHEET 10 OF 10 BOLT, MACHINE - SPLINE DRIVE EXTENDED, WASHER HEAD, PD SHANK, LONG THREAD, UNS N07001, METRIC NOTES:
11、1. MATERIAL: CORROSION AND HEAT RESISTANT STEEL, AMS 5708 (UNS N07001).2. HEAT TREATMENT: SOLUTION, STABILIZATION, AND PRECIPITATION HEAT TREATED PER MA3378.3. HARDNESS: 34 TO 44 HRC.4. FLUORESCENT PENETRANT INSPECTION: AMS 2645, ACCEPTANCE CRITERIA PER MA3378.5. PROCUREMENT SPECIFICATION: MA3378.6.
12、 SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 3.2 m Ra.7. BREAK EDGES 0.1 TO 0.4, UNLESS OTHERWISE SPECIFIED.8. DIMENSION AND TOLERANCING: ANSI Y14.5M.9. TOLERANCE GRADES TO ANSI B4.2.10. DIMENSIONS IN MILLIMETERS.11. PART NUM
13、BER SHALL INCLUDE THE STANDARD NUMBER AND THE DASH NUMBER TO INDICATE DIAMETER AND LENGTH. EXAMPLE OF PART NUMBER:a. MA3513-060012 = BOLT, MJ6 X 1 THREAD, 12 LONGb. MA3513-100026 = BOLT, MJ10 X 1.25 THREAD, 26 LONG12. DO NOT USE UNASSIGNED PART NUMBERS.13. WRENCHING CONFIGURATION SHALL BE IN ACCORDA
14、NCE WITH MA1549. FOR THE APPLICABLE DASH NUMBER, SEE TABLE 1.14. FOR PART NUMBERS WHERE SHANK LENGTH N IS EQUAL TO OR LESS THAN SHANK DIA D, THE THREAD DATUM A SHALL REPLACE DATUM B.15. WHEN SHANK LENGTH “P” (P=N-R) IS LESS THAN D, THE RUNOUT OF SHANK D RELATIVE TO DATUM A SHALL BE MEASURED AT A DISTANCE OF HALF OF THE ACTUAL FULL SHANK LENGTH FROM END OF INCOMPLETE THREAD.16. AS, MA, AND AMS ARE SAE PUBLICATIONS.17. ANSI IS AN AMERICAN NATIONAL STANDARDS INSTITUTE PUBLICATION.
