UNE 30 019 《分析试剂 醋酸铵CH3COONH4M 77 08》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D836-B1-2012 ABS ELECTROPLATING GRADE MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D836-B2-2012 ABS ELECTROPLATING GRADE MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M4D836-B1).pdf

FORD WSS-M4D840-A4-2006 ACETAL (POM) COPOLYMER COLOR PIGMENTED MOLDING COMPOUND MELT FLOW RATE 1 8 - 4 0 INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用熔体流动速率为1 8-4 0的乙缩醛共聚物(.pdf

FORD WSS-M4D840-A5-2011 ACETAL (POM) COPOLYMER MOLDED-IN-COLOR INTERIOR LOW GLOSS MELT FLOW RATE 11 C 18 g 10 MINUTES TO BE USED WITH FORD WSS-M99P1111-A 《内部低光泽着色模塑且熔态流动率为11-18 g.pdf

FORD WSS-M4D840-A6-2008 ACETAL (POM) COPOLYMER MOLD IN COLOR METALLIC MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用乙缩醛共聚物(POM)着色模塑金属状成型料 与标准FORD WSS-M99P1.pdf

FORD WSS-M4D840-B1-2011 ACETAL (POM) COPOLYMER MOLDED-IN-COLOR INTERIOR MELT FLOW RATE 7 - 11 g 10 MINUTES TO BE USED WITH FORD WSS-M99P1111-A 《内部用着色模塑且熔态流动率为7-11 g 10 min的乙缩醛(PO.pdf

FORD WSS-M4D840-B1-2015 ACETAL (POM) COPOLYMER MOLDED-IN-COLOR INTERIOR UV STABLE TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D841-A4-2011 POLYPROPYLENE (PP) COPOLYMER 11 - 17% MINERAL FILLED HIGH MELT FLOW MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《11-17%矿物填充高熔态流动聚丙烯(PP)共聚物模塑材料 与.pdf

FORD WSS-M4D841-A5-2011 POLYPROPYLENE (PP) COPOLYMER 11 - 17% MINERAL FILLED HIGH MELT FLOW MOLDING COMPOUND 25% MINIMUM PCR TO BE USED WITH FORD WSS-M99P1111-A 《11-17%矿物填充高熔态流动2.pdf