1、BSI Standards Publication PD ISO/TS 13399-312:2016 Cutting tool data representation and exchange Part 312: Creation and exchange of 3D models Reamers for indexable insertsPD ISO/TS 13399-312:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-31
2、2:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necess
3、ary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 89401 5 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Publ
4、ished Document was published under the authority of the Standards Policy and Strategy Committee on 31 March 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-312:2016 ISO 2016 Cutting tool data representation and exchange Part 312: Creation and exchange of 3D models Reamers
5、 for indexable inserts Reprsentation et change des donnes relatives aux outils coupants Partie 312: Cration et change des modles 3D Alsoirs plaquettes amovibles TECHNICAL SPECIFICATION ISO/TS 13399-312 Reference number ISO/TS 13399-312:2016(E) First edition 2016-02-15PD ISO/TS 13399-312:2016ISO/TS 1
6、3399-312:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photoc
7、opying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22
8、749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgPD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E)Foreword v Introduction vii 1 Scope . 1 2 Normative references 1 3 Starting elements, coordinate systems, planes 2 3.1 General . 2 3.2 Reference system 2 3.3 Primary coordinate system and mount
9、ing coordinate system . 2 3.4 Coordinate system at the cutting part 3 3.5 Planes 3 3.6 Design of the pocket seat and cutting reference point (CRP) of the insert . 4 3.7 Adjustment coordinate system on workpiece side 6 3.7.1 General 6 3.7.2 Designation of the coordinate system workpiece side . 6 4 De
10、sign of the model . 7 4.1 General . 7 4.2 Necessary parameters for the connection interface feature . 8 4.3 Necessary properties for inserts . 8 4.3.1 General 8 4.3.2 Properties of inserts for reaming operations 9 4.3.3 Design of the pocket seat feature. 9 5 Cylindrical reamer 9 5.1 General . 9 5.2
11、Necessary properties 10 5.3 Basic geometry .11 5.4 Determination of the position of the mounting coordinate system of insert 11 5.5 Chip flute and pocket seat 12 5.6 Cylindrical reamer Assembly .13 6 Tapered reamer 14 6.1 General 14 6.2 Necessary properties 14 6.3 Basic geometry .15 6.4 Determinatio
12、n of the position of the mounting coordinate system of insert 15 6.5 Chip flute and pocket seat 16 6.6 Tapered reamer, assembled 17 7 St epped (pr ofile) r eamer 17 7.1 General 17 7.2 Necessary properties 18 7.3 Basic geometry .19 7.4 Determination of the position of the mounting coordinate system o
13、f insert 20 7.5 Chip flute and pocket seat 21 7.6 Assembled stepped (profile) reamer 23 8 Bell style reamer23 8.1 General 23 8.2 Necessary properties 24 8.3 Basic geometry .25 8.4 Determination of the position of the mounting coordinate system of insert 26 8.5 Chip flute and pocket seats 28 8.6 Asse
14、mbled bell style reamer 29 9 Shell reamer .29 9.1 General 29 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E)9.2 Necessary properties 30 9.3 Basic geometry .30 9.4 Determination of the position of the mounting coordinate system of insert 31 9.5 Chip flut
15、e and pocket seats 32 9.6 Assembled shell reamer .33 10 Design of details .34 10.1 Basics for modelling 34 10.2 Contact/clamping surfaces Orientation 34 10.3 Chamfers and roundings .35 11 Attributes of surfaces Visualization of the model features 35 12 Structure of the design elements (tree of model
16、) .35 13 Data exchange model 36 Annex A (informative) Information about nominal dimensions 38 Bibliography .39 iv ISO 2016 All rights reservedPD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national stand
17、ards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International orga
18、nizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its
19、 further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/dir
20、ectives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in t
21、he Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions rel
22、ated to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the fo
23、llowing parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification
24、Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technic
25、al Specification Part 80: Creation and exchange of 3D models Overview and principles Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D model
26、s Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creation and exchange of 3D models Replaceable inserts for drilling Technical Specification Part 204: Creation and exchange of 3D models Inserts for reaming Tech
27、nical Specification Part 301: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of thread cutting taps, thread forming taps and thread cutting dies Technical Specification ISO 2016 All rights reserved vPD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E) Part
28、302: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid drills and countersinking tools Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with solid cutting
29、edges Technical Specification Part 304: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of milling cutters with arbor hole and solid cutting edges Technical Specification Part 307: Creation and exchange of 3D models End mills for indexable inserts Techni
30、cal Specification Part 308: Creation and exchange of 3D models Milling cutters with arbor hole for indexable inserts Technical Specification Part 309: Creation and exchange of 3D models Tool holders for indexable inserts Technical Specification Part 311: Creation and exchange of 3D models Solid ream
31、ers Technical Specification Part 312: Creation and exchange of 3D models Reamers for indexable inserts Technical Specification Part 401: Creation and exchange of 3D models Converting, extending and reducing adaptive items Technical Specification Part 405: Creation and exchange of 3D models Collets T
32、echnical Specification The following parts are under preparation: Part 70: Graphical data layout Layer settings for tool designs Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part
33、72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML data exchange Technical Specification Part 305: Creation and exchange of 3D models Modular tooling systems with adjustable cartridges for boring Technical Specification Part 310: Cr
34、eation and exchange of 3D models T urning tools with carbide tips Technical Specificationvi ISO 2016 All rights reservedPD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E) Introduction This part of ISO/TS 13399 defines the concept, the terms and the definitions on how to design simplified 3D models of
35、reamers for indexable cutting edges that can be used for NC-programming, simulation of the manufacturing processes and the determination of collision within machining processes. It is not intended to standardize the design of the cutting tool itself. A cutting tool is used in a machine to remove mat
36、erial from a workpiece by a shearing action at the cutting edges of the tool. Cutting tool data that can be described by ISO/TS 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts, solid tools, assembled tools, adaptors,
37、 components and their relationships can be represented by ISO/TS 13399 (all parts). The increasing demand providing the end-user with 3D models for the purposes defined above is the basis for the development of this series of International Standards. The objective of ISO/TS 13399 (all parts) is to p
38、rovide the means to represent the information that describes cutting tools in a computer sensible form that is independent from any particular computer system. The representation will facilitate the processing and exchange of cutting tool data within and between different software systems and comput
39、er platforms and support the application of this data in manufacturing planning, cutting operations and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing product databases and for archiving. The
40、methods that are used for these representations are those developed by ISO/TC 184 for the representation of product data by using standardized information models and reference dictionaries. Definitions and identifications of dictionary entries are defined by means of standard data that consist of in
41、stances of the EXPRESS entity data types defined in the common dictionary schema, resulting from a joint effort between ISO/TC 184/SC 4 and IEC/TC 3/SC 3D and in its extensions defined in ISO 13584-24 and ISO 13584-25. ISO 2016 All rights reserved viiPD ISO/TS 13399-312:2016PD ISO/TS 13399-312:2016C
42、utting tool data representation and exchange Part 312: Creation and exchange of 3D models Reamers for indexable inserts 1 Scope This part of ISO/TS 13399 specifies a concept for the design of tool items, limited to any kind of reamers for indexable cutting edges, together with the usage of the relat
43、ed properties and domains of values. This part of ISO/TS 13399 specifies a common way of design simplified models that contain the following: definitions and identifications of the design features of reamers for indexable cutting edges, with an association to the used properties; definitions and ide
44、ntifications of the internal structure of the 3D model that represent the features and the properties of reamers for indexable cutting edges. The following are outside the scope of this part of ISO/TS 13399: applications where these standard data may be stored or referenced; concept of 3D models for
45、 cutting tools; concept of 3D models for cutting items; concept of 3D models for other tool items not being described in the scope of this part of ISO/TS 13399; concept of 3D models for adaptive items; concept of 3D models for assembly items and auxiliary items. 2 Normative references The following
46、documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TS 13399-3, Cutti
47、ng tool data representation and exchange Part 3: Reference dictionary for tool items ISO/TS 13399-4, Cutting tool data representation and exchange Part 4: Reference dictionary for adaptive items ISO/TS 13399-50:2013, Cutting tool data representation and exchange Part 50: Reference dictionary for ref
48、erence systems and common concepts ISO/TS 13399-60, Cutting tool data representation and exchange Part 60: Reference dictionary for connection systems ISO/TS 13399-80, Cutting tool data representation and exchange Part 80: Creation and exchange of 3D models Overview and principles ISO/TS 13399-204,
49、Cutting tool data representation and exchange Part 204: Creation and exchange of 3D models Inserts for reaming TECHNICAL SPECIFICATION ISO/TS 13399-312:2016(E) ISO 2016 All rights reserved 1PD ISO/TS 13399-312:2016ISO/TS 13399-312:2016(E) 3 Starting elements, coordinate systems, planes 3.1 General The modelling of the 3D models shall be d
