1、.a71The Generaluse of thisMETRICA-A-1507AJune 28. 1993SUPERSEDINGA-A-1507February 27, 1981COMMERCIAL ITEM DESCRIPTIONCHIPBOARDServices Administration hes authorized thecommercial item description in preferenceto Federal Specification UU-C-282,-which is-canceled.SCOPE: This commercial item descriptio
2、n covers Chipboard usedfor general protection and packaging where etrength andappearance are not essential.1.A.B.c.D.-SALIENT CHARACTERISTICSMaterial. Chipboard shall be prepared by processingmateriale to Ineure compliance with the requirements of thisdescription. The chipboard shall be plain and eh
3、all not becoated or lined. Two or more plies can be combined.Form and size. Chipboard shall be furnished in sheet formwhich shall be cut to the eize specified. The tolerance forthe width and length dimensions shall be minue zero and plus6.35 mm (1/4 inch). Unless otherwise epecified, the sizeshall b
4、e one of the followina: 21.59 cm X 27.94 cm (8-1/2” X11”); 25.4 cm X 28.58 cm (lO; X 11-1/4”); 66.04 cm x“96.52(26” X 3S”); 121.92 cm X 121.92 cm (48” X 48”)Color. The color ehall be natural and may have variationashade.Thickness. The thickness shell be as specified (ace tablewith a tolerance of plu
5、s or minus 0.076 mm (0.003”) whentested in accordance with TAPPI T 411.cmin1),- - - - - - - - -;Beneficial comments, recommendations, additions, deletions, I!clarifications, etc. and any data which may improve thie ,ldocument should be sent to the General Services Administration;Federal Supply Servi
6、ce, Engineering Branch, 26 Federal Pleza :iNew York, N.Y. 10278. 1- - - -; DISTRIBUTION STATEMENT A: Approved for ;: public release; distribution is unlimited. :- -FSC 8135Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-1507AE. Basis weight. The
7、basis weight of chlpboard shall be asspecified (see table I) with a tolerance of plus or minus 5percent when tested in accordance with TAPPI T 410.TASLE I. Physical requirementsI Basis weightIThickness 1 lbs/1000 sq ft1 I2.413 mm (0.095”) - 3151.524 mm (0.060”) j 1005.69 2061.016 mm (0.040”) i 663.9
8、5 II 1360.635 mm (0.025”) : 439.38 I 900.508 mm (0.020”) : 351.50 I 72IF. Workmanship. Chipboard shall be free fom surface lumps, clipindentations, wrinkles, cracke, breaks, blows, blisters,split edges, soil and mechanical imperfections or any otherdefects which may impair its serviceability or appe
9、arance.2. RECOVERED MATERIALSThe contractor must certify that the product offered shallinclude a minimum of 80 % post-consumer recovered material asdefined in 40 CPR, Part 250. The Government reserves the rightto require proof of such conformance prior to first delivery andthereafter as may be other
10、wise provided for under the provisionsof the contract.3. QLJALI= ASSURANCEResponsibility for Inspection - Unless otherwise specified in thecontract or purchase order, the eupplier Is responsible for theperformance of all Inspection requirements as specified herein.Except as otherwise specified, the
11、supplier may utillze his ownfacilities or any commercial laboratory acceptable to.thegovernment. The Government reserves the right to perform any ofthe inspections set forth herein, where such Inspections aredeemed necessary to assure that supplies and services conform tothe prescribed requir-ents.E
12、ach lot of sheets shall be Inspected for conformance to therequirements herein. Inspection ehall be in accordance with MIL-STD-105 using the qempling plans specified below.A. Visual characteristics - Inspection, level S-4 with anAcceptable Quality level (AQL) of 4.0 percent defective, Thesample unit
13、 shall be one sheet.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IA-A-1507AIB.c.D.4.Dimensional characteristics - Inspection level S-4 with anAcceptable Quality level (AQL) of 4.0 Percent defective. Thesample unit shall be one sheet.TAPPI tests s
14、hall be in accordance with TAPPI T 400 for theapplicable TAPPI test method.Packaging, Packing, Labeling and Marking - Inspection levelS-2 with an AQL of 4.0 percent defective. The eample unitshall be one fully prepared shipping container.APPLICATION FOR COPIES OF DOCUMENTS REFERENCED HEREIN:The Iesu
15、e date in effect on date of invitation for bids orrequest for proposal shall apply.A. MIL-STD-105 is available from Standardization Documents OrderDesk; Building 4D: 700 Robbina Avenue: Philadelphia, PA19111 - 5094.B. Code of Federal Regulationa, Title 40, Part 250 is availablethrough the Superinten
16、dent of documents, U.S. GovernmentPrinting Office, Washington DC 20402.c. TAPPI 1400,T41O & T411 are available from the TechnicalAaeociation of the Pulp and Paper Industry, P.O. Box 105113,Atlanta, GA, 30348.5. PREPARATION FOR HANDLING:Packaging, Packing, Labeling, and Marking ehall be as specifiedi
17、n the contrect or purchase order.6. ORDERING DATA:Purchaser should reference this commercial item description whenordering and state their requirements for a) size b) thicknessc) packaging, packing, labeling, and marking.No official DOD interesthas been registeredPreparing ActivityGSA-FSS3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
