1、HIL-C-LO750J 4 = 777970b 037b752 2 s- /5- I / MIL-C-107SOJ SUPERSEDING MIL-C-107 SOH 31 December 1981 17 June 1988 MILITARY SPECIFICATION COAT, FIREMANS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers an ou
2、ter coat with liner; 1.2 Classification. The coat shall be of one type in the following classes and sizes (see 6.2): Class 1 - White Class 2 - Olive Green 107 Schedule of sizes Small Medium Large X-Large =-Large Short-Regular Short-Regular Short-Regular Short-Regular Short-Regular Long Long Long Lon
3、g Long Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document
4、Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I AMSC NIA FSC 841s * DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. t- P THIS DOCUMENT CONTAINS ST PAGES. - _=_ - A Licensed by Information Handling ServicesMIL-C-LO750J L( W 7
5、779706 0376753 Li i. MIL-C-10750J ,. . 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handb-_ks. Th following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of
6、 these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDEAL * A-A-203 V-B-87 1 V-T-280 FF-R-556 FF-W-92 QQ-N-290 QQ-P-416 DDD-L-20 PPP-B-636 MILITARY MIL-C-373
7、5 MIL-F-10884 MIL-E-20652/1 MIL-F-21848 * MIL-L-35078 MIL-C-43122 MIL-C-43410 MIL-T-4363 6 MIL-C-43 774 MIL-C-43708 MIL-B-81813 Paper, Kraft, Untreated Button, Sewing Hole, and Button, Staple, (Plastic) Thread, Gimp, Cotton, Buttonhole Rivet, Solid, Small; Rivet, Split, Small; Rivet, Tubular, Small;
8、 Flatwasher (Burr); and Cap, Rivet; General Purpose Washers, Flat (Plain) Nickel Plating (Electrodeposited) Plating, Cadmium (Electrodeposited) Label: For Clothing, Equipage and Tentage, (General Boxes, Shipping, Fiberboard Use) Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted Fasteners , Snap Eyele
9、t, Metallic, Rolled Flange Type; and Eyelet Fastener Tapes, Hook and Loop, Synthetic Loads Unit: Preparation of Semi-perishable Washer Subsistence Items; Clothing, Personal Equipment and Equipage Cloth, Sateen, Cotton, Flame Resistant Treated Cloth, Coated: Polyester/Cotton, Polyester/Rayon; Polyvin
10、yl Chloride or Polychloroprene Coated Thread , Aramid Cloth, Plain or Pajama Check Weave, Aramid Cloth, Coated, or Cloth, Laminated, Reflective Batting, Aramid or Novoloid Fiber, Quilted 2 Licensed by Information Handling Services* MIL-C-107 50 J SPECIFICATIONS STANDARDS FEDERAL FED-STD-191 - Textil
11、e Test Methods FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets Attributes L (Copie
12、s of specifications, standards, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this specification to t
13、he extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernm
14、ent documents which are current on the date of solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS D 1424 - Tear Resistance of Woven Fabrics by Falling-Pendulum (Elmendorf) Apparatus D 3951 - Standard Practice for Commercial Packaging (Copies may be obtained from the American Society for Testin
15、g and Material-s, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. documents also may be available in or through libraries or other informational services 1 These
16、2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has be
17、en obtained. 3 Licensed by Information Handling Services_ MIL-C-LO750J 4 7997706 0376755 m MIL-C-10750J c 3. REQUIREMENTS * 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). 3.2 Guide sample. Samples,
18、 when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this document may appear in the sample, in which case this document shall govern. * 3.3. Materials. Materials shall be as specified herein (see 6.7). 3.3.1 Basic material. The material for the outer
19、 shell shall be fire resistant and water repellent treated, cotton sateen, conforming to MIL-(2-43122, in the following colors and classes: Glass 1 Coat - Bleached White, Class and a size 1 eyelet with stud for the male half, conforming to style 2, finish 2 of MIL-F-10884. 3.3.15 Rivets, tubular wit
20、h caps. The rivets for attaching snaps and dees shall be 9/64 inch nominal size; 5/16 inch nominal length conforming to type XII, class 3, grade B or F of FF-R-566 except that the inside of the rivet shank shall be chamfered. The caps shall conform to type II of FF-R-556. The brass rivets shall be n
21、ickel plated conforming to class 2, ,0005 inch minimum thickness of QQ-N-290. The aluminum rivets shall be used in conjunction with the aluminum or zinc snaps and dees and the brass rivets shall be used in conjunction with the brass snaps and dees. As an alternate, washers conforming to type A, grad
22、e II, class C, No. 8 of FF-W-92 may be used in lieu of the caps. 3.3.16 Buttons. The buttons to attach sleeves of liner to coat shall be type II, class D, style 4, 27-line conforming to V-B-871. The color of the buttons shall be Olive Green, shade BP, Cable No. 62016 and shall have a glossy finish.
23、3.4 Design. The coat, as shown on figure 1, is a single breasted model, with a wide corduroy cloth storm collar, which includes a throat strap secured in place by fastener tape and long shaped sleeves with wrist wells ending in wristlets. It has side patch pockets with an additional layer for reinfo
24、rcement, eyelets for passage of water with pocket flaps. There is a front protective flap closed by means of rigid snaps and dees. There are three vertical reflectorized/fluorescent cloth strips down the front of the coat, strips forming a box configuration in the back, two horizontal strips around
25、the sleeves, and a horizontal strip around the hem of the coat. The outer shell of the coat is backed by a vapor barrier lining, and a quilted batting liner is permanently attached to the outer shell lining at the neckline only. 3.5 Figures. Figures 1 and 4 are furnished solely for guidance and Shou
26、ld variation fron the written document appear in the figure, information. the written document shall govern. 3.6 Patterns. Standard patterns providing an allowance of 318 inch for safety stitch and single needle seams, and 112 inch for double needle seams will be furnished by the Government to the c
27、ontractor for cutting working patterns. 8 Licensed by Information Handling ServicesMIL-C-1 O 750 J The Government patterns, which show directional lines and markings for proper assembly, shall not be altered in any way except as authorized by footnotes to table II, and are to be used as a guide for
28、cutting contractors working patterns. The working patterns shall be identical to the Government patterns. 3.7 List of pattern parts. The coat and liner shall be cut frommaterials as specified with the number of parts indicated in table II, TABLE II. List of pattern parts Mat er ia1 Nomenclature Cut
29、parts QUTER SHELL Flame resistant cotton sateen Cotton corduroy Coated cloth Aramid batting Front Back Sleeve Pocket Pocket flap Pocket reinforcement Storm flap Undercollar Undercollar interlining Undercollar stand Undercollar stand interlining Top collar stand Front interlining Necktab Top collar 1
30、 LINING Front Back Sleeve Wris twe i1 Storm flap facing LINER - Front Back Sleeve 2 2 2 1 2 21 2 - i/ Use same pattern part. 2/ Parts may be cut in two pieces with seam allowances added. - 9 Licensed by Information Handling Services_- . - MIL-C-LO750J 4 W 7777706 0376763 3 MIL-C-107 50 J * 3.8 Const
31、ruction. The construction shall conform in all respects to the requirements specified in table III and herein. * 3.8.1 Stitches, seams and stitching. Stitch, seam, stitching types and stitches per inch specified in table III shall conform to FED-STD-751. Where two or more seam or stitch types are gi
32、ven for the same part of an operation, any one of them may be used. sewn so that no raw edges, run-Offs, twists, pleats, puckers, or open seams will result. All seams shall start and finish evenly. The edge and top stitching shall be uniformly gaged. Seams required to be worked out, that have a dept
33、h between the fold of 1/16 inch or more shall be considered a defect. The gage of stitching on double stitched seams shall be 1/4 to 5/16 inch, but the same gage shall be used on all double stitched seams throughout the coat with the outside row of stitching being 1/16 to 1/8 from the edge. safety s
34、titch construction shall be 3/8 f 1/16 inch. The guides and knives on the safety stitch machines shall be set to trim only the ravelled ends of the fabric. Seam allowances shall be maintained with seams The gage of stitching for 3.8.1.1 Type 301 stitching. Ends of stitching shall be backstitched or
35、overstitched 1/2 inch minimum except when caught in other stitching or turned under in a hem. Thread tension shall be maintained so that there will be no loose stitching resulting in puckering of the materials sewn. The lock shall be embedded in the materials sewn. 0 3.8.1.1.1 Repairs of type 301 st
36、itching. Repairs of type 301 stitching shall be as follows: a. When thread breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum of 1 inch behind the end of the stitching. - i/ b. Thread breaks, or two or more consecutive skipped or r
37、un-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1 inch in back of the defective area and continue a minimum of 1 inch beyond the defective area on to the existing stitching. by removing the defect
38、ive stitching, without damaging the materials, and restitching in the required manner, - l/ Loose or excessively tight stitching shall be repaired L/ When making the above repairs, the ends of the stitchng are not required to be backstitched. 3.8.1.2 Type 401 stitching. Thread tension shall be maint
39、ained so that there will be no loose stitching. 401 stitch type, when not turned under in a hem or held down by other stitching, shall have a 1/2 to 3/4 inch chain extending beyond each end. (underthread) shall be on the inside of the coat. accordance with 3.8.1.1.la and 3.8.1.1.lb. type Both ends o
40、f all seams or stitching produced with The looper Repairs may be made using 301 stitch All repairs shall be in 10 Licensed by Information Handling ServicesMIL-C-10 7 50 J * 3.8.1.3 Types 503, 504, 515, 516, and 519 stitching. Thread tension shall be maintained so that there will be no loose stitchin
41、g. All repairs shall be in accordance with 3.8.1.1,la and 3.8.1.1.lb, except substitute 3/4 inch for 1 inch wherever 1 inch appears. The looper (under thread) of 515, 516 and 519 type stitching shall be on the inside of the coat. The guides and knives on the safety stitch machine shall be set to tri
42、m only the ravelled end of the fabric. O * 3.8.1.4 Bartacking. Unless otherwise specified, bartacks shall be as specified in table III and as follows: O Length Width 1/2 inch - + 1/16 1/8 inch - + 1/32 Bartacks shall be free of thread breaks and loose stitching. * 3.8.1.5 Automatic stitching. Automa
43、tic stitching machines may be used to perform any of the required patterns provided the requirements of the stitch pattern, stitches per inch, size and type of thread are met, and at least three or more tying, overlapping, or backstitches are used to secure the ends of the stitching. 3.8.1.6 Thread
44、ends. All thread ends that are visible on the finished item shall be trimmed to a length of not more than 114 inch. 3.8.1.7 Buttonholes. The buttonholes shall be eyelet end, taper bar type, worked over gimp with not less than four tacking stitches at bar end (not counting crossover stitch) and shall
45、 have a finished cut length of 3/4 to 7/8 inch. The stitching shall be securely caught in the fabric and the ends shall be securely tacked. All loose thread ends shall be trimmed or fused to within 1/8 inch of the tack. 3.8.1.8 Setting of snap fasteners. A hole shall be prepunched to receive the but
46、ton and eyelet components of the snap fastener. The hole shall be smaller than the outside diameter of the button and eyelet barrels so that the barrel must be forced through the hole. operation with the button or eyelet barrel. clinched without cutting the adjacent materials and no more than three
47、splits shall occur in the button or eyelet barrels. The hole shall not be punched in the setting The fasteners shall be securely * 3.9 Repairs. Repairs such as mends, darns, patches or splices are not permitted on the coat. 3.10 Manufacturing operations requirements. The coats and liners shall be ma
48、nufactured in accordance with aperation requirements specified in table III. The contractor is not required to follow the exact sequence of operations. Any additional basting or holding stitching is permissible provided the thread does not show in the finished garment. 11 Licensed by Information Han
49、dling ServicesMIL-C-LO750J 84 7777906 0376763 7 = MIL-C-107 50 J * * 3.11 Marking. The component parts of the coat and liner shall be marked, ticketed or bundled to insure a uniform shade and size throughout the garment, Any method of marking may be used except: (1) Metal fastening devices (2) Sew-on type tickets (3) Adhesive type tickets, which discolor and adhere to the material upon removal of the tickets 12 Licensed by Information Handling ServicesMIL-C-1075OJ m Gal ka al UP um (d Ch- al .rl v) 5 .$: h 3 alm oalm o cdrl o drl (docd .rl uuw ou0 *rl
