1、19 September 1983 SUPERSEDING MIL-L-43672B 10 November 1976 MILITARY SPECIFICATION LINER, SNOW CAMOUFLAGE TROUSERS: WHITE ARCTIC, M-65 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers a trouser liner made fr
2、om quilted poly est er batting ma te ri al . 1.2 Classification, The liner shall be of one type in the following sizes (see 6.2): Schedule of Sizes Short and Regular Long X-Small Small Medium Large X-Large 2. APPLICABLE DOCUMENTS X-Small Small Medium Large X-Large * 2.1 Government documents . Unless
3、 otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this document to the extent specified herein: Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving
4、this document should be addressed to: U.S. Army Natick Research and Development Laboratories, Natick, NA 01760, by using the self-addressed standardization Document Improvement Proposal (DD Form 1426) appearing.at the end of this document or by letter. FSC 8415 THIS DOCUMENT CONTAINS 26 PAGES. , Pro
5、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* _-I- MIL-L-43672C 4 7777706 0375407 3 MIL-L-436 72C SPECIFICATIONS FEDERAL A-A-203 V-B-8 7 1 . V-T- 2 80 J J-W- 15 5 DDD-L-20 PPP-B-636 MILITARY MIL-C-5 08 MIL-B-4 18 26 MIL-T-4 35 48 STANDARDS FEDERAL F
6、ED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 Paper, Kraft, Untreated Button, Sewing Hole, and Button, Staple, (Plastic) Thread, Gimp, Cotton, Buttonhole Webbing, Textile (Cotton, Elastic) Label: For Clothing, Equipage, and Tentage Boxes, Shipping, Fiberboard (General Use) Cloth, Oxford, Nylon, 3 Ounc
7、e Batting, Synthetic Fibers; Polyester (Qullted Thread, Polyester, Cotton-Covered and Rayon-Covered and Unquilted) Stitches, Seams, and Stitchings Sampling Procedures and Tables for Inspection Marking for Shipment and Storage by Attributes (Copies of documents required by manufacturers in connect io
8、n with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. Unless otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of
9、 this document to the extent specified herein. THE COLOR ASSOCIATION OF THE UNITED STATES INC. Standard Color Card of America (Application for copies should be addressed to the Color Association of the United States Inc., 24 East 38th Street, New York, NY 10016.) 3u . 2 Provided by IHSNot for Resale
10、No reproduction or networking permitted without license from IHS-,-,-MIL-L-43b72C 84 W 9797906 0395408 5 - MIL-L-43672C O * a O AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society fo
11、r Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. using Federal agencies.) They are also distributed among technical groups and * 2.3 Order of precedence. In the event of a
12、conflict between the text of this document and the references cited herein, the text of this document shall take precedence. 30 REQUIREMENTS 3.1 Guide sample. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.3). the sample, in which case this document s
13、hall govern, Variation from the document may appear in 3.2 Materials (see 6.4). 3,2.1 Basic material. The basic material shall be a quilted polyester batting, conforming to type IV, class 3, style a, of MIL-B-41826. 3.2.2 Waistband and binding. The material for waistband, side opening facings, and b
14、ias binding shall be nylon oxford cloth, natural in color, conforming to type I, class 2 of MIL-C-508. 3.2.3 Labels. Each liner shall have an identification label, a size label, and an instruction label conforming to DDD-L-20. The labels shall show fastness to laundering. 3.2.3.1 Identification labe
15、l* The identification label shall conform to type VI, class 1. 3.2.3.2 Size label. The size label shall conform to type VI, class 2, and contain the following information for each respective size. X-Small-Short and Regular Waist: Below 27 inches Inseam: p to 32-1/2 inches Stock No. NATO Size: 6783/5
16、869 3 X-mal 1-Long Waist: Below 27 inches Inseam: Over 32-1/2 inches Stock NO. NATO Size: 8390/5869 E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - _ -_- MIL-L-43b72C 84 = 7797706 0375407 7 Small-Short and Regular Waist: From 27 to 31 inches Ins
17、eam: Up to 32-1/2 inches . MIL-L-43672C Small -Long Waist: From 27 to 31 inches Inseam: Over 32-1/2 inches Stock No. Stock No. NATO Size: 6783/6979 NATO Size: 8390/6979 Medium-Short and Regular Waist: From 31 to 35 inches Inseam: Up to 32-1/2 inches Stock No. NATO Size: 678317989 Large-Short Regular
18、 Waist: From 35 to 39 inches Inseam: Up to 32-1/2 inches Stock No. NATO Size: 6783/8999 X-Large-Short and Regular Waist: From 39 to 43 inches Inseam: Up to 32-1/2 inches Stock No. NATO Size: 6783/9909 Medium-Long Waist: From 31 to 35 inches Inseam: Over 32-1/2 inches Stock No. NATO Size: 8390/7989 L
19、arge-Long Waist: From 35 to 39 inches Inseam: Over 32-1/2 inches Stock NO. NATO Size: 8390/8999 X-Large-Long Waist: From 39 to 43 inches Inseam: Over 32-1/2 inches Stock NO. NATO Size: 8390/9909 * 3.2.3.3 Instruction label. The instruction label shall conform to type VI, class 3, and shall contain t
20、he following information: LINER, COLD WEATHER TBOUSERS, FIELD 1. Button into trousers for extra warmth. 2. . 3. 4. Dry liner and trousers separately when damp or wet. Avoid contact with heated stoves, open fires or other Wash by hand or machine in warm water with mild soap or heat sources; fabric ma
21、y fuse. detergent, rinse thoroughly, and drip dry or machine dry. Do NOT DRY CLEAN. DO NOT REMOVE THIS LABEL * 3.2.3.4 Combination size and identification label. The identification label (class 1) and the size label (class 2) may be combined into one label conforming to type VI, classes 1 and 2 comb
22、ined. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e . e O MIL-L-43672C 4 9999906 0395410 3 W MIL-L-43672C * 3.2.3.5 Combination size, identification and instruction labei. The identi- fication label (class i), size label (class 2) and instructi
23、on label (class 3) may be combined in one label conforming to class 14. conform to class 3 label. The coating requirements shall 3.2.4 Thread. The thread shall be polyester cotton-covered and rayon-covered conforming to MIL-T-43548 ticket number 30, 2 or 3 ply or 50, 2 or 3 ply for stitching and sea
24、ming, 70-2 ply for overedging, and 30, 2 or 3 ply for buttonholes and button sewing. The color shall be white. 3.2.5 Gimp. The cotton gimp for reinforcing buttonholes shall be size No. 8, natural or bleached, conforming to type I or II of V-T-280. 3.2.6 Buttons. The buttons shall be type II, class D
25、, style 26, 30-line of V-B- 871. The buttons shall be DOD button shade White BA, C.A. 62031, and have a dull finish. * 3.2.7 Elastic. The elastic for the waistband shall be type I, bleached or unbleached, class 6 of JJ-W-155. 3.3 Design. The design of the liner shall be a button in liner (see figure
26、 1). 3.4 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government. Government patterns which shall not be altered in any way. seam allowance of 1/2 inch for all seams (to finish 3/8 inch wide). The working patterns shall be identical to the The patterns prov
27、ide a 3.4.1 Pattern parts. The component parts shall be cut from the materials specified below in accordance with pattern parts indicated in table I. TABLE I. List of pattern parts _- Mate ri al Pattern nomenclature Cut parts Basic material Front Back 2 2 * 3.5 Construction. The construction shall c
28、onform in all respects to the requirements specified in table II and herein. guidance and information. this document shall govern. Figure 1 is furnished solely for Should variation from this document appear in figure 1, * 3.5.1 Stitches, seams, and stitching. Ail stitches, seams and stitching shall
29、conform to FED-STD-751. as specified in table I. that no raw edges, run-Offs, pleats, puckers, or open seams occur. The type of seam, stitching and stitches per inch shall be Seam allowances shall be maintained with seams sewn so When two or 5 Provided by IHSNot for ResaleNo reproduction or networki
30、ng permitted without license from IHS-,-,-MIL-L-4 36 7 2 C more methods of seams or stitches are given for the same operation, any one may be used. or inside of the liner. shall be on the outside of the liner. The side of the liner worn nearest the body shall be considered the inside. Where stitch t
31、ype 401 is used, the looper (underthread) may be on the outsid The reverse side of the seam type LSbm-3 (overedge side) * 3.5.1.1 Typ e 301 stitching. Ends of all stitching shall be backstitched or overstitched not less than 1/4 inch except where ends are turned under or caught in other seams or sti
32、tching. Ends of a continuous line of stitching shall overlap not less than 1/2 inch. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. in the materials sewe
33、d. The lock shall be imbedded * 3.5.1.1.1 Repairs of type 301 stitching. 3.5.1.1.1.1 Quilted batting stitching. Broken stitches of the quilting pattern may be repaired by stitching back of each end of break not less than 1 inch. 3.5.1.1.1.2 Liner fabrication Stitching. a. When thread breaks or bobbi
34、n run-outs occur during stitching, except prestitching, the stitching shall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. - l/ b. Except for prestitching, thread breaks, or two or more consecutive skipped or run-off stitches noted during inspection o
35、f the item shall be repaired by overstitching. defective area, continue over the defective area, and continue a minimum of 1/2 inch beyond the defective area onto the existing stitching. stitching shall be repaired by removing the defective stitching without damaging the materials, and restitching i
36、n the required manner. L/ The stitching shall start a minimum of 1/2 inch in back of the Loose or excessively tight - i/ When making the above repairs, the ends of the stitching are not required to be backstitched. * 3.5.1.2 Type 401, 503, 504, 515, 516, 517, 518, and 519 stitching. Thread tension s
37、hall be maintained so that there will be no loose stitching. All repairs shall be in accordance with 3.5.1.1.1.2a. and 3.5.1.1.1.2b. maintained so that there will be no loose or excessively tight stitching resulting in puckering of the materials sewn. Thread tension shall be * 3.5.4 Buttonholes. The
38、 buttonholes shall be eyelet-end-taper-bar-type worked over gimp (see 3.2.5) with not less than four tacking stitches at bar end, not counting cross over stitch. The finished cut length shall be 3/4 to 7/8 inch. buttonholes shall be clean cut with the stitching securely caught in the fabric. The 6 P
39、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43672C 84 m 7799706 0395412 7 m MIL-L-46372C 3.6 Manufacturing operations requirements. The liner shall be manufactured in accordance with operations specified in table II. follow the exact sequenc
40、e of operations. stitching may be used providing the threads are removed or are not visible on the The contractor is not required to Any additional basting or holding O finished liner . 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-436 72C
41、rn E al a B 3 3 i3 B rl O w a P U VJ .ri $4 O w o 4 o FI al o I a, k 14 3 2 . a o u o jWdWdW w !2 . -i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-436 72C I O rn O rn n mal m 4 d 9rl cr) O ci N 4 I N al bo a al pi O. uu cd 4B al sw cdo 4 al
42、 albo Na I! *u 4 rl . m u d al E # O 0 al 3 d U c) al w al a w O U 0 al o cd 4 Ff 2 slcia r: ar: a-w aj 31 cdwalo P . el . m . .;f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - - MIL-L-43672C 4 7979906 0375435 2 - IY w O V 7 ce ZW ma mo M-l O0 U
43、 -I P w w Z - i 2 5 I O 4 2 I O 4 2 I O 4 4- 4 1 O 4 n a M W k 5: d n a M W k $ d n a M W LI : d d c; Ag U FI a, P U a O 4 P iiiu vid0 du Q“ D :Y;. a Md dd0 *U w 3 d L x w I- Z 3 2 LL O z 2 != tl w r O Ca Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
44、-,-MIL-L-43672C BL( 3999906 0395420 b M - MIL-L-43672C a ! al a (d al 2 4 4 (d al * O al or off center on waist lining by more than 1/4 inch (measured from center to button) d. Buttons and buttonholes out of alignment causing noticeable bulge when liner is buttoned Position of horizontal buttonhole
45、a. Inside edge of eyelet not required measurement from finished edge of right front and front side openings , b. C. Off center on waist lining by more than 1/4 inch Purling not finishing on the outside of liner X X X X X X X X X X X X X X 21 Provided by IHSNot for ResaleNo reproduction or networking
46、 permitted without license from IHS-,-,-_I_ _-. _-I_-_ MIL-L-43672C 4 7797906 0375427 7 W MIL-L-43672C Classification Major Minor Defects AB Vertical buttonholes at waist a. Purling not finishing toward the body b. than 3/4 inch from top edge of waist inside edge of eyelets less than 1/2 inch or mor
47、e Labels (size, ident if icat ion, ins truct ion or combinat ion, when applicable) a. b. Identification label missing, incorrect or illegible c. d. Size, instruction or combination (when applicable) labels missing, incorrect or illegible Off center on right back by more than 1 inch Not stitched on a
48、ll sides or not positioned as specified (as worn) X X X X X X * 4.2.3 End item dimensional examination. The end item shall be examined for Any dimension not within conformance to the dimensions specified in table IV. the specified tolerance shall be classified as a defect. The lot size shall be expr
49、essed in units of liners. inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 4.0. The sample unit shall be one liner. The 4.2.4 Examination of packaging requirements. An examination shall be made to determine that the preservation, packing and marking comply with t
