1、Designation: D1785 15Standard Specification forPoly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80,and 1201This standard is issued under the fixed designation D1785; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of
2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers poly
3、(vinyl chloride) (PVC)pipe made in Schedule 40, 80, and 120 sizes and pressure-ratedfor water (see Appendix X1). Included are criteria for classi-fying PVC plastic pipe materials and PVC plastic pipe, asystem of nomenclature for PVC plastic pipe, and requirementsand test methods for materials, workm
4、anship, dimensions,sustained pressure, burst pressure, flattening, and extrusionquality. Methods of marking are also given.1.2 The products covered by this specification are intendedfor use with the distribution of pressurized liquids only, whichare chemically compatible with the piping materials. D
5、ue toinherent hazards associated with testing components and sys-tems with compressed air or other compressed gases somemanufacturers do not allow pneumatic testing of their products.Consult with specific product/component manufacturers fortheir specific testing procedures prior to pneumatic testing
6、.NOTE 1Pressurized (compressed) air or other compressed gasescontain large amounts of stored energy which present serious safteyhazards should a system fail for any reason.NOTE 2This standard specifies dimensional, performance and testrequirements for plumbing and fluid handling applications only. I
7、t doesnot include provisions for the use of these products for venting ofcombustion gases. UL 1738 is a standard that does include specific testingand marking requirements for flue gas venting products, including PVC.1.3 The text of this specification references notes, footnotes,and appendixes which
8、 provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of the specification.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units
9、 that are provided for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest methods portion, Section 8, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the re
10、sponsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use. A specific precautionary statement is givenin Note 9.NOTE 3CPVC plastic pipes, Schedules 40 and 80, which wereformerly included in thi
11、s specification, are now covered by SpecificationF441/F441M.NOTE 4The sustained and burst pressure test requirements, and thepressure ratings in the Appendix X1, are calculated from stress valuesobtained from tests made on pipe 4 in. (100 mm) and smaller. However,tests conducted on pipe as large as
12、24-in. (600-mm) diameter have shownthese stress values to be valid for larger diameter PVC pipe.NOTE 5PVC pipe made to this specification is often belled for use asline pipe. For details of the solvent cement bell, see Specification D2672and for details of belled elastomeric joints, see Specificatio
13、ns D3139 andD3212.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe, Tubing, and FittingsD
14、1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of
15、 ExtrudedPoly(Vinyl Chloride) (PVC) Pipe and Molded Fittings byAcetone ImmersionD2672 Specification for Joints for IPS PVC Pipe UsingSolvent Cement1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.25 on V
16、inylBased Pipe.Current edition approved Aug. 1, 2015. Published August 2015. Originallyapproved in 1960. Last previous edition approved in 2012 as D1785 12. DOI:10.1520/D1785-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.
17、For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D283
18、7 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure Design Basisfor Thermoplastic Pipe ProductsD3139 Specification for Joints for Plastic Pressure PipesUsing Flexible Elastomeric SealsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using F
19、lexible Elastomeric SealsF412 Terminology Relating to Plastic Piping SystemsF441/F441M Specification for Chlorinated Poly(Vinyl Chlo-ride) (CPVC) Plastic Pipe, Schedules 40 and 802.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking fo
20、r Shipment and Storage32.4 NSF/ANSI Standards:4Standard No. 14 for Plastic Piping System Components andRelated MaterialsStandard No. 61 for Drinking Water System ComponentsHealth Effects2.5 UL Standard:5UL 1738 Standard for Venting Systems for Gas-BurningAppliances, Categories II, III, and IV3. Term
21、inology3.1 Definitions:Definitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600, unless otherwise specified. The abbreviation forpoly(vinyl chloride) plastic is PVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 hydrostatic design str
22、essthe estimated maximumtensile stress the material is capable of withstanding continu-ously with a high degree of certainty that failure of the pipewill not occur. This stress is circumferential when internalhydrostatic water pressure is applied.3.2.2 pressure rating (PR)the estimated maximum water
23、pressure the pipe is capable of withstanding continuously witha high degree of certainty that failure of the pipe will not occur.3.2.3 relation between dimensions, design stress, and pres-sure ratingthe following expression, commonly known asthe ISO equation,6is used in this specification to related
24、imensions, hydrostatic design stress, and pressure rating:2S/P 5 D0/t! 2 1where:S = hydrostatic design stress, psi (or MPa),P = pressure rating, psi (or MPa),D0= average outside diameter, in. (or mm), andt = minimum wall thickness, in. (or mm).3.2.4 standard thermoplastic pipe materials designationc
25、odethe pipe materials designation code shall consist of theabbreviation PVC for the type of plastic, followed by theASTM type and grade inArabic numerals and the design stressin units of 100 psi (0.7 MPa) with any decimal figures dropped.When the design stress code contains less than two figures, ac
26、ipher shall be used before the number. Thus a completematerial code shall consist of three letters and four figures forPVC plastic pipe materials (see Section 5).4. Classification4.1 GeneralThis specification covers PVC pipe made toand marked with one of six type/grade/design stress designa-tions (s
27、ee X1.2) in Schedule 40, 80, and 120 wall sizes.4.2 Hydrostatic Design StressesThis specification coverspipe made from PVC plastics as defined by four hydrostaticdesign stresses which have been developed on the basis oflong-term tests (Appendix X1).5. Materials and Manufacture5.1 GeneralPoly(vinyl c
28、hloride) plastics used to makepipe meeting the requirements of this specification are catego-rized by means of two criteria, namely, (1) short-term strengthtests and (2) long-term strength tests.NOTE 6The PVC pipe intended for use in the transport of potablewater should be evaluated and certified as
29、 safe for this purpose by a testingagency acceptable to the local health authority. The evaluation should bein accordance with requirements for chemical extraction, taste, and odorsthat are no less restrictive than those included in NSF/ANSI Standard No.14. The seal or mark of the laboratory making
30、the evaluation should beincluded on the pipe. See pipe marking requirement for reclaimed watersystems.5.2 Basic MaterialsThis specification covers pipe madefrom PVC plastics having certain physical and chemicalproperties as described in Specification D1784.5.3 CompoundThe PVC compounds used for this
31、 pipeshall equal or exceed the following classes described inSpecification D1784; PVC 12454, or 14333.5.4 Rework MaterialThe manufacturer shall use only hisown clean rework pipe material and the pipe produced shallmeet all the requirements of this specification.6. Requirements6.1 Dimensions and Tole
32、rances:6.1.1 Dimensions and tolerances shall be as shown in Table1 and Table 2 when measured in accordance with Test MethodD2122. The tolerances for out-of-roundness shall apply only topipe prior to shipment.6.2 Sustained PressureThe pipe shall not fail, balloon,burst, or weep as defined in Test Met
33、hod D1598, at the testpressures given in Tables 3-5 when tested in accordance with8.4.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.4Available from NSF International, P.O. Box 130140, 789 N. D
34、ixboro Rd., AnnArbor, MI 48113-0140, http:/www.nsf.org.5Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas,WA 98607-8542, http:/.6ISO R161-1960, Pipes of Plastics Materials for the Transport of Fluids (OutsideDiameters and Nominal Pressures) Part 1, Metric Series.D1785 1526.2.1
35、 Accelerated Regression TestThe accelerated regres-sion test shall be used in place of both the sustained and burstpressure tests, at the option of the manufacturer. The test shallbe conducted in accordance with 8.4.1. The pipe shall demon-strate a hydrostatic design basis projection at the 100 000-
36、hintercept that meets the hydrostatic design basis categoryrequirement (see Tables 3-5 and Test Method D2837) for thePVC material used in its manufacture. (Example: PVC 1120pipe must have a minimum 100 000-h projection of 3830 psi(26.40 MPa) and 85 % lower confidence limit (LCL).TABLE 1 Outside Diam
37、eters and Tolerances for PVC Plastic Pipe Schedules 40, 80, and 120, in. (mm)Nominal Pipe Size Outside DiameterTolerancesAverageMaximum Out-of-Roundness (maximum minus minimumdiameter)Schedule 40 sizes 312 in. andover; Schedule 80 sizes 8 in.and overSchedule 40 sizes 3 in. andless;Schedule 80 sizes
38、6 in. andless;Schedule 120 sizes all18 0.405 (10.29) 0.004 (0.10) . . . 0.016 (0.41)14 0.540 (13.72) 0.004 (0.10) . . . 0.016 (0.41)38 0.675 (17.14) 0.004 (0.10) . . . 0.016 (0.41)12 0.840 (21.34) 0.004 (0.10) . . . 0.016 (0.41)34 1.050 (26.67) 0.004 (0.10) . . . 0.020 (0.51)1 1.315 (33.40) 0.005 (0
39、.13) . . . 0.020 (0.51)114 1.660 (42.16) 0.005 (0.13) . . . 0.024 (0.61)112 1.900 (48.26) 0.006 (0.15) . . . 0.024 (0.61)2 2.375 (60.32) 0.006 (0.15) . . . 0.024 (0.61)212 2.875 (73.02) 0.007 (0.18) . . . 0.030 (0.76)3 3.500 (88.90) 0.008 (0.20) . . . 0.030 (0.76)312 4.000 (101.60) 0.008 (0.20) 0.10
40、0 (2.54) 0.030 (0.76)4 4.500 (114.30) 0.009 (0.23) 0.100 (2.54) 0.030 (0.76)5 5.563 (141.30) 0.010 (0.25) 0.100 (2.54) 0.060 (1.52)6 6.625 (168.28) 0.011 (0.28) 0.100 (2.54) 0.070 (1.78)8 8.625 (219.08) 0.015 (0.38) 0.150 (3.81) 0.090 (2.29)10 10.750 (273.05) 0.015 (0.38) 0.150 (3.81) 0.100 (2.54)12
41、 12.750 (323.85) 0.015 (0.38) 0.150 (3.81) 0.120 (3.05)14 14.000 (355.60 0.015 (0.38) 0.200 (5.08) . . .16 16.000 (406.40) 0.019 (0.48) 0.320 (8.13) . . .18 18.000 (457.20) 0.019 (0.48) 0.360 (9.14) . . .20 20.000 (508.00) 0.023 (0.58) 0.400 (10.2) . . .24 24.000 (609.60) 0.031 (0.79) 0.480 (12.2) .
42、 . .TABLE 2 Wall Thicknesses and Tolerances for PVC Plastic Pipe, Schedules 40, 80, and 120,A,Bin. (mm)Nominal PipeSizeWall ThicknessASchedule 40 Schedule 80 Schedule 120Minimum Tolerance Minimum Tolerance Minimum Tolerance18 0.068 (1.73) +0.020 (+0.51) 0.095 (2.41) +0.020 (+0.51) . . . . . .14 0.08
43、8 (2.24) +0.020 (+0.51) 0.119 (3.02) +0.020 (+0.51) . . . . . .38 0.091 (2.31) +0.020 (+0.51) 0.126 (3.20) +0.020 (+0.51) . . . . . .12 0.109 (2.77) +0.020 (+0.51) 0.147 (3.73) +0.020 (+0.51) 0.170 (4.32) +0.020 (+0.51)34 0.113 (2.87) +0.020 (+0.51) 0.154 (3.91) +0.020 (+0.51) 0.170 (4.32) +0.020 (+
44、0.51)1 0.133 (3.38) +0.020 (+0.51) 0.179 (4.55) +0.021 (+0.53) 0.200 (5.08) +0.024 (+0.61)114 0.140 (3.56) +0.020 (+0.51) 0.191 (4.85) +0.023 (+0.58) 0.215 (5.46) +0.026 (+0.66)112 0.145 (3.68) +0.020 (+0.51) 0.200 (5.08) +0.024 (+0.61) 0.225 (5.72) +0.027 (+0.68)2 0.154 (3.91) +0.020 (+0.51) 0.218
45、(5.54) +0.026 (+0.66) 0.250 (6.35) +0.030 (+0.76)212 0.203 (5.16) +0.024 (+0.61) 0.276 (7.01) +0.033 (+0.84) 0.300 (7.62) +0.036 (+0.91)3 0.216 (5.49) +0.026 (+0.66) 0.300 (7.62) +0.036 (+0.91) 0.350 (8.89) +0.042 (+1.07)312 0.226 (5.74) +0.027 (+0.68) 0.318 (8.08) +0.038 (+0.96) 0.350 (8.89) +0.042
46、 (+1.07)4 0.237 (6.02) +0.028 (+0.71) 0.337 (8.56) +0.040 (+1.02) 0.437 (11.10) +0.052 (+1.32)5 0.258 (6.55) +0.031 (+0.79) 0.375 (9.52) +0.045 (+1.14) 0.500 (12.70) +0.060 (+1.52)6 0.280 (7.11) +0.034 (+0.86) 0.432 (10.97) +0.052 (+1.32) 0.562 (14.27) +0.067 (+1.70)8 0.322 (8.18) +0.039 (+0.99) 0.5
47、00 (12.70) +0.060 (+1.52) 0.718 (18.24) +0.086 (+2.18)10 0.365 (9.27) +0.044 (+1.12) 0.593 (15.06) +0.071 (+1.80) 0.843 (21.41) +0.101 (+2.56)12 0.406 (10.31) +0.049 (+1.24) 0.687 (17.45) +0.082 (+2.08) 1.000 (25.40) +0.120 (+3.05)14 0.437 (11.10) +0.053 (+1.35) 0.750 (19.05) +0.090 (+2.29) . . . .
48、. .16 0.500 (12.70) +0.060 (+1.52) 0.843 (21.41) +0.101 (+2.57) . . . . . .18 0.562 (14.27) +0.067 (+1.70) 0.937 (23.80) +0.112 (+2.84) . . . . . .20 0.593 (15.06) +0.071 (+1.80) 1.031 (26.19) +0.124 (+3.15) . . . . . .24 0.687 (17.45) +0.082 (+2.08) 1.218 (30.94) +0.146 (+3.71) . . . . . .AThe mini
49、mum is the lowest wall thickness of the pipe at any cross section. The maximum permitted wall thickness, at any cross section, is the minimum wall thicknessplus the stated tolerance. All tolerances are on the plus side of the minimum requirement.BThese dimensions conform to nominal IPS dimensions, with the exception that Schedule 120 wall thickness for pipe sizes12 to 312 in. (12.5 to 87.5 mm), inclusive, arespecial PVC plastic pipe sizes.D1785 1536.3 Burst PressureThe minimum bur
