1、Designation: D445 142British Standard 2000: Part 71: Section 1: 1996Designation: 71 Section 1/97Standard Test Method forKinematic Viscosity of Transparent and Opaque Liquids(and Calculation of Dynamic Viscosity)1This standard is issued under the fixed designation D445; the number immediately followi
2、ng the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved
3、 for use by agencies of the U.S. Department of Defense.1NOTEIP designation, British Standard designation, and 17.1.1 were updated editorially in September 2014.2NOTESection 17 was corrected editorially in September 2014.1. Scope*1.1 This test method specifies a procedure for the determi-nation of th
4、e kinematic viscosity, , of liquid petroleumproducts, both transparent and opaque, by measuring the timefor a volume of liquid to flow under gravity through acalibrated glass capillary viscometer. The dynamic viscosity, ,can be obtained by multiplying the kinematic viscosity, ,bythe density, , of th
5、e liquid.NOTE 1For the measurement of the kinematic viscosity and viscosityof bitumens, see also Test Methods D2170 and D2171.NOTE 2ISO 3104 corresponds to Test Method D445 03.1.2 The result obtained from this test method is dependentupon the behavior of the sample and is intended for applicationto
6、liquids for which primarily the shear stress and shear ratesare proportional (Newtonian flow behavior). If, however, theviscosity varies significantly with the rate of shear, differentresults may be obtained from viscometers of different capillarydiameters. The procedure and precision values for res
7、idual fueloils, which under some conditions exhibit non-Newtonianbehavior, have been included.1.3 The range of kinematic viscosities covered by this testmethod is from 0.2 mm2/s to 300 000 mm2/s (see Table A1.1)at all temperatures (see 6.3 and 6.4). The precision has onlybeen determined for those ma
8、terials, kinematic viscosityranges and temperatures as shown in the footnotes to theprecision section.1.4 The values stated in SI units are to be regarded asstandard. The SI unit used in this test method for kinematicviscosity is mm2/s, and the SI unit used in this test method fordynamic viscosity i
9、s mPas. For user reference, 1 mm2/s =10-6m2/s = 1 cSt and 1 mPas=1cP=0.001 Pas.1.5 WARNINGMercury has been designated by manyregulatory agencies as a hazardous material that can causecentral nervous system, kidney and liver damage. Mercury, orits vapor, may be hazardous to health and corrosive tomat
10、erials. Caution should be taken when handling mercury andmercury containing products. See the applicable product Ma-terial Safety Data Sheet (MSDS) for details and EPAswebsitehttp:/www.epa.gov/mercury/faq.htmfor addi-tional information. Users should be aware that selling mercuryand/or mercury contai
11、ning products into your state or countrymay be prohibited by law.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the appl
12、ica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D446 Specifications and Operating Instructions for GlassCapillary Kinematic ViscometersD1193 Specification for Reagent WaterD1217 Test Method for Density and Relative Density (Spe-cific Gravity) of Liquids b
13、y Bingham PycnometerD1480 Test Method for Density and Relative Density (Spe-cific Gravity) of Viscous Materials by Bingham Pycnom-eter1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility ofSubcommittee D
14、02.07 on Flow Properties.Current edition approved July 1, 2014. Published August 2014. Originallyapproved in 1937. Last previous edition approved in 2012 as D445 12. DOI:10.1520/D0445-14E02.In the IP, this test method is under the jurisdiction of the StandardizationCommittee.2For referenced ASTM sta
15、ndards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM Inter
16、national, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D1481 Test Method for Density and Relative Density (Spe-cific Gravity) of Viscous Materials by Lipkin BicapillaryPycnometerD2162 Practice for Basic Calibration of Master Viscometersand Viscosity Oil Standar
17、dsD2170 Test Method for Kinematic Viscosity of Asphalts(Bitumens)D2171 Test Method for Viscosity of Asphalts by VacuumCapillary ViscometerD6071 Test Method for Low Level Sodium in High PurityWater by Graphite Furnace Atomic Absorption Spectros-copyD6074 Guide for Characterizing Hydrocarbon Lubricant
18、Base OilsD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System PerformanceD6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products andLubricantsD6617 Practice for Laboratory B
19、ias Detection Using SingleTest Result from Standard MaterialE1 Specification for ASTM Liquid-in-Glass ThermometersE77 Test Method for Inspection and Verification of Ther-mometersE1137/E1137M Specification for Industrial Platinum Resis-tance Thermometers2.2 ISO Standards:3ISO 3104 Petroleum ProductsT
20、ransparent and OpaqueLiquidsDetermination of Kinematic Viscosity and Cal-culation of Dynamic ViscosityISO 3105 Glass Capillary Kinematic ViscometersSpecification and Operating InstructionsISO 3696 Water for Analytical Laboratory UseSpecification and Test MethodsISO 5725 Accuracy (trueness and precis
21、ion) of measurementmethods and results.ISO 9000 Quality Management and Quality AssuranceStandardsGuidelines for Selection and UseISO 17025 General Requirements for the Competence ofTesting and Calibration Laboratories2.3 NIST Standards:4NIST Technical Note 1297 Guideline for Evaluating andExpressing
22、 the Uncertainty of NIST Measurement Re-sults5NIST GMP 11 Good Measurement Practice for Assignmentand Adjustment of Calibration Intervals for LaboratoryStandards6NIST Special Publication 819 Guide for the Use of theInternational System of Units (SI)73. Terminology3.1 See also International Vocabular
23、y of Metrology.83.2 Definitions:3.2.1 digital contact thermometer (DCT), nan electronicdevice consisting of a digital display and associated tempera-ture sensing probe.3.3 Definitions of Terms Specific to This Standard:3.3.1 automated viscometer, napparatus which, in part orin whole, has mechanized
24、one or more of the procedural stepsindicated in Section 11 or 12 without changing the principle ortechnique of the basic manual apparatus. The essential ele-ments of the apparatus in respect to dimensions, design, andoperational characteristics are the same as those of the manualmethod.3.3.1.1 Discu
25、ssionAutomated viscometers have the capa-bility to mimic some operation of the test method whilereducing or removing the need for manual intervention orinterpretation. Apparatus which determine kinematic viscosityby physical techniques that are different than those used in thistest method are not co
26、nsidered to be Automated Viscometers.3.3.2 density, nthe mass per unit volume of a substance ata given temperature.3.3.3 dynamic viscosity, ,nthe ratio between the appliedshear stress and rate of shear of a material.3.3.3.1 DiscussionIt is sometimes called the coefficient ofdynamic viscosity or abso
27、lute viscosity. Dynamic viscosity is ameasure of resistance to flow or deformation which constitutesa materials ability to transfer momentum in response to steadyor time-dependent external shear forces. Dynamic viscosity hasthe dimension of mass divided by length and time and its SIunit is pascal ti
28、mes second (Pas). Among the transportproperties for heat, mass, and momentum transfer, dynamicviscosity is the momentum conductivity.3.3.4 kinematic viscosity, ,nthe ratio of the dynamicviscosity () to the density () of a material at the sametemperature and pressure.3.3.4.1 DiscussionKinematic visco
29、sity is the ratio be-tween momentum transport and momentum storage. Suchratios are called diffusivities with dimensions of length squareddivided by time and the SI unit is metre squared divided bysecond (m2/s). Among the transport properties for heat, mass,and momentum transfer, kinematic viscosity
30、is the momentumdiffusivity.3.3.4.2 DiscussionFormerly, kinematic viscosity was de-fined specifically for viscometers covered by this test methodas the resistance to flow under gravity. More generally, it is theratio between momentum transport and momentum storage.3.3.4.3 DiscussionFor gravity-driven
31、 flow under a givenhydrostatic head, the pressure head of a liquid is proportionalto its density, , if the density of air is negligible compared tothat of the liquid. For any particular viscometer covered by thistest method, the time of flow of a fixed volume of liquid is3Available from American Nat
32、ional Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from National Institute of Standards and Technology (NIST), 100Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.5http:/physics.nist.gov/cuu/Uncertainty/bibliography.html6http:/ts.nist.gov/
33、WeightsAndMeasures/upload/GMP_11_Mar_2003.pdf7http:/www.nist.gov/pml/pubs/sp811/index.cfm8International Vocabulary of Metrology Basic and General Concepts andAssociated Terms (VIM), 3rd ed., 2008, http:/www.bipm.org/en/publications/guides/vim.html.D445 1422directly proportional to its kinematic visc
34、osity, , where = , and is the dynamic viscosity.4. Summary of Test Method4.1 The time is measured for a fixed volume of liquid toflow under gravity through the capillary of a calibratedviscometer under a reproducible driving head and at a closelycontrolled and known temperature. The kinematic viscos
35、ity(determined value) is the product of the measured flow timeand the calibration constant of the viscometer. Two suchdeterminations are needed from which to calculate a kinematicviscosity result that is the average of two acceptable deter-mined values.5. Significance and Use5.1 Many petroleum produ
36、cts, and some non-petroleummaterials, are used as lubricants, and the correct operation ofthe equipment depends upon the appropriate viscosity of theliquid being used. In addition, the viscosity of many petroleumfuels is important for the estimation of optimum storage,handling, and operational condi
37、tions. Thus, the accurate deter-mination of viscosity is essential to many product specifica-tions.6. Apparatus6.1 ViscometersUse only calibrated viscometers of theglass capillary type, capable of being used to determinekinematic viscosity within the limits of the precision given inthe precision sec
38、tion.6.1.1 Viscometers listed in Table A1.1, whose specificationsmeet those given in Specifications D446 and in ISO 3105 meetthese requirements. It is not intended to restrict this test methodto the use of only those viscometers listed in Table A1.1.Annex A1 gives further guidance.6.1.2 Automated Vi
39、scometersAutomated apparatus maybe used as long as they mimic the physical conditions,operations or processes of the manual apparatus. Anyviscometer, temperature measuring device, temperaturecontrol, temperature controlled bath or timing device incorpo-rated in the automated apparatus shall conform
40、to the specifi-cation for these components as stated in Section 6 of this testmethod. Flow times of less than 200 s are permitted, however,a kinetic energy correction shall be applied in accordance withSection 7 on Kinematic Viscosity Calculation of SpecificationsD446. The kinetic energy correction
41、shall not exceed 3.0 % ofthe measured viscosity. The automated apparatus shall becapable of determining kinematic viscosity of a certifiedviscosity reference standard within the limits stated in 9.2.1and Section 17. The precision shall be of statistical equivalenceto, or better (has less variability
42、) than the manual apparatus.NOTE 3Precision and bias of kinematic viscosity measurements forflow times of less than 200 s has not been determined. The precision statedin Section 17 is not know to be valid for kinematic viscosity measure-ments with flow times less than 200 s.6.2 Viscometer HoldersUse
43、 viscometer holders to enableall viscometers which have the upper meniscus directly abovethe lower meniscus to be suspended vertically within 1 in alldirections. Those viscometers whose upper meniscus is offsetfrom directly above the lower meniscus shall be suspendedvertically within 0.3 in all dire
44、ctions (see Specifications D446and ISO 3105).6.2.1 Viscometers shall be mounted in the constant tempera-ture bath in the same manner as when calibrated and stated onthe certificate of calibration. See Specifications D446, seeOperating Instructions in Annexes A1A3. For those viscom-eters which have T
45、ube L (see Specifications D446) heldvertical, vertical alignment shall be confirmed by using (1)aholder ensured to hold Tube L vertical, or (2) a bubble levelmounted on a rod designed to fit into Tube L, or (3) a plumbline suspended from the center of Tube L, or (4) other internalmeans of support pr
46、ovided in the constant temperature bath.6.3 Temperature-Controlled BathUse a transparent liquidbath of sufficient depth such, that at no time during themeasurement of flow time, any portion of the sample in theviscometer is less than 20 mm below the surface of the bathliquid or less than 20 mm above
47、 the bottom of the bath.6.3.1 Temperature ControlFor each series of flow timemeasurements, the temperature control of the bath liquid shallbe such that within the range from 15 C to 100 C, thetemperature of the bath medium does not vary by more than60.02 C of the selected temperature over the length
48、 of theviscometer, or between the position of each viscometer, or atthe location of the thermometer. For temperatures outside thisrange, the deviation from the desired temperature must notexceed 60.05 C.6.4 Temperature Measuring Device in the Range from 0 to100 CUse either calibrated liquid-in-glass
49、 thermometers(Annex A2) with an accuracy after correction of 60.02 C orbetter, or a digital contact thermometer as described in 6.4.2with equal or better accuracy.6.4.1 If calibrated liquid-in-glass thermometers are used, theuse of two thermometers is recommended. The two thermom-eters shall agree within 0.04 C.6.4.2 When using a digital contact thermometer (DCT) thefollowing shall apply:(1) The only acceptable sensors are a resistance tempera-ture device (RTD), such as a platinum resistance thermometer(PRT)
