1、Designation: E1120 08E1120 16Standard Specification forLiquid Chlorine1This standard is issued under the fixed designation E1120; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses in
2、dicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers industrial grade chlorine normally available a
3、s a liquid in pressurized metal containers.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 Review the current Material Safety Data Sheets (MSDS)(SDS) for detailed information concerning toxicity, first aidprocedures, hand
4、ling and safety precautions.1.4 The following safety hazards caveat pertains only to the test methods listed in Sections 3 and 4. This standard does notpurport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard toestablish ap
5、propriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E410 Test Method for Moisture and Residue in Liquid ChlorineE1746 Test Method for Sampling and Analysis of Liquid Chlorine for Gaseous Impurities2.2
6、 Federal Documents:Federal Specification PPP-C-2020A, Chemicals, Liquid, Dry, and Paste, Packaging of (supersedes PPP-C-2020)3Title 49 CFR, Department of Transportation, Parts 100 to 1994Title 40 CFR, Protection of the Environment, Parts 162 to 1804Title 29 CFR, Labor, Part 1910.1200, New Requiremen
7、ts as to Container Labeling, Occupational Safety and HealthAdministration (OSHA)43. Chemical Requirements3.1 Liquid chlorine shall conform to the following requirements:Gaseous impurities, %volume (v/v) (% by vol)0.5 max E1746Moisture, % mass (m/m)(% by weight)0.015 max E410Nonvolatile material, % m
8、ass(m/m) (% by weight)0.015 max E4104. Sampling4.1 Sample liquid chlorine in accordance with the appropriate sections of Test Method E1746.1 This specification is under the jurisdiction ofASTM Committee D16 on Aromatic Hydrocarbons and Related Chemicals and is the direct responsibility of Subcommitt
9、eeD16.16 on Industrial and Specialty Product Standards.Current edition approved April 1, 2008Nov. 1, 2016. Published May 2008November 2016. Originally approved in 1986. Last previous edition approved in 20022008 asE1120 97 (2002). 08. DOI: 10.1520/E1120-08.10.1520/E1120-16.2 For referencedASTM stand
10、ards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Single copies of Federal Specifications required for bidding purposes are available f
11、rom General ServicesAdministration Business Service Centers in Boston, New York,Washington, DC, Philadelphia, Atlanta, Chicago, Kansas City, MO, Fort Worth, Houston, San Francisco, Los Angeles, and Seattle, WA.4 The Code of Federal Regulations may be obtained from the U.S. Government Printing Office
12、 732 N. Capitol St. NW, Washington, DC 20401, http:/www.gpoaccess.gov/CFR/index.html.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to
13、adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright A
14、STM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Packaging and Package Marking5.1 Package and label industrial and commercial quantities in accordance with Department of Transportation CFR Title 49 Part100 to 199, and state and local regulatio
15、ns.5.2 When specified, Department of Defense Procurements shall be packaged and labeled in accordance with the applicableparagraphs of Federal Specification PPP-C-2020A.5.3 Label chlorine to be used as a pesticide in accordance with the applicable regulations of the Environmental ProtectionAgency as
16、 described in CFR Title 40, Parts 162 to 180.5.4 Labeling also must comply with OSHAregulations described in CFR Title 29 Part 1910 and Section 1910.1200 as publishedin 48 Federal Register 53280.6. Keywords6.1 chlorine; liquidSUMMARY OF CHANGESCommittee E15D16 has identified the location of selected
17、 changes to this standard since the last issue(E112097(2002)E1120)08) that may impact the use of this standard. (Approved November 1, 2016.)(1) Updated units of measure to comply with the International System of Units (SI).Removed “Material” from (MSDS) statementin Scope section 1.3.(2) Added subsec
18、tion to Scope stating that SI units are considered standard.(3) Added MSDS and safety hazards caveats to Scope.(4) Added Summary of Changes section.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users
19、of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every fi
20、ve years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical c
21、ommittee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA
22、 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 162
