1、Designation: F 1074 87 (Reapproved 2007)An American National StandardStandard Specification forCleats, Welded Horn Type1This standard is issued under the fixed designation F 1074; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the
2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers hollow cleats and pads formarine use.1.2 The cleats shall be used where securing o
3、f boat handlinglines are required onboard commercial and navy boats andcrafts.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural
4、 SteelA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 385 Practice for Providing High-Quality Zinc Coatings(Hot-Dip)3. Ordering Information3.1 Orders for material under this specification shall includethe following:3.1.1 Title, number, and date of this specification,3.1.2
5、 Quantity,3.1.3 Size of cleats, and3.1.4 Packaging, packing, or marking requirements.4. Materials and Manufacture4.1 Material:4.1.1 The horn cleats shall be of galvanized steel, grade1023W, in accordance with Practice A 385.4.1.2 The base plate shall be of steel, (carbon 0.35 maxi-mum), in accordanc
6、e with Specification A 36/A 36M.4.1.3 All chafing surfaces shall have a 125 finish.4.2 ManufactureThe cleats horns shall be of cast steel,round in shape, and free of burrs or sharp edges. The hornsshall be welded to a base plate as shown in Fig. 1 (see Table 1).The weld is to be ground smooth to pre
7、vent chafing of ropes.The base plate shall be oval shaped with smooth roundededges. The dimensions shall be in accordance with Table 1.5. Packaging5.1 The packing shall afford protection against deteriorationand physical damage during shipment from the manufacturer tothe using activity for immediate
8、 use.6. Product Marking6.1 Containers shall be stenciled with the ASTM standarddesignation, in black paint with approximately 1 in. (25.4 mm)high letters and numbers with the following information:6.1.1 Address,6.1.2 purchase order number, and6.1.3 Manufacturers name.7. Keywords7.1 base plates; boat
9、 handling lines; cleats; hollow cleats;horn cleats; marine; marine cleats; ship; welded cleats1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition appr
10、oved Dec. 1, 2007. Published January 2008. Originallyapproved in 1987. Last previous edition approved in 2002 as F1074 - 87(2002).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informat
11、ion, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTESee Table 1 for dimensions.FIG. 1 Welded Horn Type Cleat (16 in.)F 1074 87 (2007)2SUPPLEMENTARY REQUIREMENTSThe
12、following supplementary requirement shall apply only when specified by the purchaser in thecontract or order.S1. Quality Assurance ProvisionsS1.1 Responsibility for InspectionThe purchaser reservesthe right to perform any of the inspections set forth in thespecification where such inspections are de
13、emed necessary toassure that supplies and services conform to prescribed require-ments.S1.2 Source InspectionThe purchaser reserves the rightto inspect the manufacturing process and end product in thesuppliers plant.S1.3 TestsThe cleats shall meet the test load requirementsof Table 1, as tested in a
14、ccordance with Test Methods andDefinitions A 370.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights
15、, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for re
16、vision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing yo
17、u shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be
18、 obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Welded Horn-Type Cleat DimensionsNOTE 1Table 1 is to be used with Fig. 1.NOTE 21 in. = 25.4 mm.NOTE 31 lb = 0.45 kg.Cleat Ro
19、pe Circumference (in.)Rope Di-ameter(in.)Cleats TestLoad (lb)Dimensions (in.)Calcu-latedWeight(lb)Manila Nylon DacronPolypro-pylene6 3 37 Fi-berCore WireRopeABCDEFGHJKLMN10 212 178 318 11453258 1332 17851614716 2 5.3 134 11112 410016 4 3 5 214 1134 31271634 314 21.7 3 2 2 212516 900024 6 412 712 338 112 258 4123434 118 412 75 5 3 3 412 23 00030 712 558 938 3341532 178 3932 558151678 1516 512 137 6 312 4558 36 000F 1074 87 (2007)3
