1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10067 : 1997 The Eu
2、ropean Standard EN 10067 : 1996 has the status of a British Standard ICS 77.140.50; 77.140.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Hot rolled bulb flats Dimensions and tolerances on shape, dimensions and massBS EN 10067 : 1997 This British Standard, having been prep
3、ared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference ISE/13 Draft for comment 92/44028 DC ISBN 0 580 27133
4、 1 Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/13, Structural steel sections, upon which the following bodies were represented: British Iron and Stee
5、l Producers Association Health and Safety Executive Department of TransportBS EN 10067 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 10067 3ii BSI 1997 BS EN 10067 : 1997 National foreword This British Standard has been prepared
6、by Technical Committee ISE/13 and is the English language version of EN 10067 : 1996, Hot rolled bulb flats Dimensions and tolerances on shape, dimensions and mass, published by the European Committee for Standardization (CEN). This British Standard completely supersedes BS 4848 : Part 5 : 1980 whic
7、h is now withdrawn. Cross-references Publication referred to Corresponding British Standard EN 10079 BS EN 10079 Definition of steel products Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an insid
8、e front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CE
9、N members Ref. No. EN 10067 : 1996 E EUROPEAN STANDARD EN 10067 NORME EUROPE ENNE EUROPA ISCHE NORM October 1996 ICS 77.140.50; 77.140.60 Descriptors: Iron and steel products, hot rolled products, metal bars, flat bars, designation, dimensions, dimensional tolerances, form tolerances English version
10、 Hot rolled bulb flats Dimensions and tolerances on shape, dimensions and mass Plats a boudin lamine sa chaud Dimensions et tole rances sur la forme, les dimensions et la masse Warmgewalzter Wulstflachstahl Mae, Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 1996-08-04.
11、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on a
12、pplication to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat h
13、as the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 10067 : 1996 BSI 1997
14、 Foreword This European Standard has been prepared by Technical Committee ECISS/TC 11, Structural steel sections, the Secretariat of which is held by BSI. The discussions within ECISS/TC 11 were based on Euronorm 67 (1978). This European Standard shall be given the status of a national standard, eit
15、her by publication of an identical text or by endorsement, at the latest by April 1997, and conflicting national standards shall be withdrawn at the latest by April 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i
16、mplement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Iceland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Designation 3 5 Dimensions 3 6 Toleran
17、ces on shape and dimensions 3 7 Tolerance on mass 3Page 3 EN 10067 : 1996 BSI 1997 1 Scope This European Standard specifies requirements for the nominal dimensions and tolerances on shape, dimensions and mass of hot-rolled bulb flats. These requirements do not apply to bulb flats rolled from stainle
18、ss steel. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to
19、or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10079 Definition of steel products 3 Definitions For the purposes of this European Sta
20、ndard the definitions in EN 10079 apply. 4 Designation The designation of the hot-rolled bulb flats shall comprise: 1) the term bulb flat; 2) the number of this European Standard; 3) the nominal width b (in mm); 4) the nominal thickness t (in mm). Example: Bulb flat EN 10067-2003 10. 5 Dimensions Ho
21、t-rolled bulb flats complying with this European Standard shall be delivered with the dimensions given in table 1 and illustrated in figure 1. NOTE. The geometric properties, the data on the cross-section, and the surface area are derived from the nominal dimensions. 6 Tolerances on shape and dimens
22、ions 6.1 Width and thickness The width and thickness tolerances shall be as given in table 2. The width shall be measured on the longer side of the leg. 6.2 Tolerance for out of squareness of weld edge The angle by which the weld edge deviates from the vertical (u) shall not exceed 4 (see figure 2).
23、 6.3 Corner radius The maximum values for the corner radius r 1 shall be as given in table 3. 6.4 Length 6.4.1 Hot-rolled bulb flats shall be delivered in lengths up to and including 18 m. Lengths greater than 18 m shall be agreed at the time of ordering. 6.4.2 The length tolerances shall be mm. Clo
24、ser 0 +100 length tolerances shall be specially agreed at the time of ordering. 6.5 Straightness The straightness tolerance q shall be 0,0035 L. The dimension q shall be measured as illustrated in figure 3 along the entire length L. 7 Tolerance on mass The mass tolerances shall be: % of the total ma
25、ss for deliveries of 5 t or more, 22 +6 and % of the total mass for deliveries of less than 5 t. 22,7 +8 The mass deviation shall be the difference between the actual delivery mass and the theoretical mass. The theoretical mass shall be calculated from the data in table 1 and the ordered length in m
26、etres. NOTE. The masses given in table 1 are derived from the sectional areas using a density of 7,85 kg/dm 3 .Page 4 EN 10067 : 1996 BSI 1997 Figure 1. Shape of bulb flat Figure 2. Tolerance for out of squareness of weld edge Figure 3. Tolerance on straightnessPage 5 EN 10067 : 1996 BSI 1997 Table
27、1. Dimensions, sectional areas, mass/unit length, surface areas and geometric properties of bulb flats Nominal size Dimensions for Area of section Mass/unit length Surface area Distance to centre of gravity Geometric properties about the x-x axis btcrAGUd x I x W x (mm) (mm) (mm) (mm) cm 2 kg/m m 2
28、/m cm cm 4 moment of inertia cm 3 elastic modulus 803 5 803 6 80 5 6 14 4 5,41 6,21 4,25 4,88 0,189 0,191 4,9 4,78 33,87 38,7 6,91 8,1 1003 7 1003 8 100 7 8 15,5 4,5 8,74 9,74 6,86 7,65 0,236 0,238 5,87 5,78 85,3 94,3 14,5 16,3 1203 6 1203 7 1203 8 120 6 7 8 17 5 9,32 10,52 11,72 7,32 8,26 9,2 0,276
29、 0,278 0,28 7,21 7,07 6,96 133 149 165 18,5 21 23,6 1403 7 1403 8 1403 10 140 7 8 10 19 5,5 12,43 13,83 16,63 9,75 10,85 13,05 0,32 0,322 0,326 8,32 8,18 7,99 241 266 315 29 32,5 39,5 1603 7 1603 8 1603 9 1603 11 160 7 8 9 11 22 6 14,6 16,2 17,8 21 11, 46 12,72 13,97 16,49 0,365 0,367 0,369 0,373 9,
30、66 9,5 9,37 9,16 373 411 449 522 38,6 43,3 47,9 57 1803 8 1803 9 1803 10 1803 11 180 8 9 10 11 25 7 18,86 20,66 22,46 24,26 14,8 16,22 17,63 19,04 0,411 0,413 0,415 0,417 10,89 10,73 10,59 10,47 609 664 717 770 55,9 61,8 67,7 73,5 2003 9 2003 10 2003 11 2003 12 200 9 10 11 12 28 8 23,66 25,66 27,66
31、29,66 18,57 20,14 21,71 23,28 0,457 0,459 0,461 0,463 12,12 11,96 11,82 11,69 942 1017 1091 1164 77,7 85,1 92,3 99,5 2203 10 2203 11 2203 12 220 10 11 12 31 9 29 31,2 33,4 22,77 24,5 26,22 0,503 0,506 0,507 13,35 13,19 13,04 1396 1496 1595 105 114 122 2403 10 2403 11 2403 12 240 10 11 12 34 10 32,49
32、 34,89 37,29 25,5 27,39 29,27 0,547 0,549 0,551 14,77 14,58 14,42 1865 1997 2127 126 137 148 2603 10 2603 11 2603 12 260 10 11 12 37 11 36,11 38,71 41,31 28,35 30,39 32,43 0,591 0,593 0,596 16,22 16 15,81 2434 2605 2774 150 163 175 2803 11 2803 12 2803 13 280 11 12 13 40 12 42,68 45,48 48,28 33,5 35
33、,7 37,9 0,637 0,639 0,641 17,44 17,23 17,04 3333 3647 3757 191 206 221 3003 11 3003 12 3003 13 300 11 12 13 43 13 46,78 49,79 52,79 36,7 39,09 41,44 0,681 0,683 0,685 18,9 18,7 18,45 4192 4459 4722 222 239 256 3203 12 3203 13 3203 14 320 12 13 14 46 14 54,25 57,45 60,85 42,6 45,09 47,6 0,728 0,73 0,
34、732 20,12 19,89 19,68 5525 5849 6168 275 294 313 3403 12 3403 13 3403 14 340 12 13 14 49 15 58,84 62,24 65,54 46,2 48,86 51,5 0,772 0,774 0,776 21,69 21,34 21,1 6757 7152 7540 313 335 357 3703 13 3703 14 3703 15 370 13 14 15 53,5 16,5 69,7 73,4 77,1 54,7 57,6 60,5 0,84 0,842 0,844 23,54 23,29 23,06
35、9469 9980 10483 402 429 456Page 6 EN 10067 : 1996 BSI 1997 Table 1. Dimensions, sectional areas, mass/unit length, surface areas and geometric properties of bulb flats (continued) Nominal size Dimensions for Area of section Mass/unit length Surface area Distance to centre of gravity Geometric proper
36、ties about the x-x axis btcrAGUd x I x W x (mm) (mm) (mm) (mm) cm 2 kg/m m 2 /m cm cm 4 moment of inertia cm 3 elastic modulus 4003 14 4003 15 4003 16 400 14 15 16 58 18 81,48 85,48 89,48 63,96 67,1 70,2 0,908 0,91 0,912 25,49 25,24 25 12924 13573 14211 507 538 568 4303 14 4303 15 4303 17 4303 19 43
37、03 20 430 14 15 17 19 20 62,5 19,5 89,7 94,19 102,79 111,39 115 70,6 73,9 80,7 87,4 90,8 0,975 0,976 0,98 0,984 0,986 27,7 27,46 26,95 26,53 26,3 16460 17249 18853 20413 21180 594 629 700 770 804 Table 2. Tolerances on dimensions Dimensions in mm Dimensions Tolerances bt #$#for b for t 120 5 8 1,5 2
38、0,3 + 0,7 120 180 7 11 2.0 20,3 + 1,0 180 300 9 13 3,0 20,4 + 1,0 300 430 12 20 4,0 20,4 + 1,2 Table 3. Maximum value of corner radius r 1 Dimensions in mm Thickness t Corner radius r 1 max # 5 1,5 592 91 33 13 20 4 BSI 1997 BS EN 10067 : 1997 List of references See national foreword.BSI 389 Chiswic
39、k High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standard
40、s Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Stand
41、ards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technica
42、l committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders
43、for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards,
44、 unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all i
45、ts products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membershi
46、p Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract m
47、ay be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols,
48、 and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
