1、BRITISH STANDARD BS EN 122003:1995 Specification for Harmonized system of quality assessment for electronic components Blankdetail specification for the Preparation of customer detail specifications (CDS) and detail specifications for standard production items with capability approval The European S
2、tandard EN122003:1994 has the status of a BritishStandardBSEN122003:1995 BSI 12-1999 ISBN 0 580 35983 2 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted to Technical Committee EPL/46, Cables, wires, waveguides, RF connectors and accessories for co
3、mmunications and signalling, upon which the following bodies were represented: British Cable Makers Confederation British Telecommunications plc Federation of the Electronics Industry Ministry of Defence Society of British Aerospace Companies Ltd The following bodies were also represented in the dra
4、fting of the standard through subcommittees: AEA Technology BEAMA Electrical Cables and Conductor Accessory Manufacturers Association National Supervising Inspectorate (BSI-PC) Society of Cable Television Engineers Amendments issued since publication Amd. No. Date CommentsBSEN122003:1995 BSI 12-1999
5、 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN122003 4BSEN122003:1995 ii BSI 12-1999 National foreword This BritishStandard has been prepared under the direction of the Electrotechnical Sector Board, and is the English language version of EN1220
6、03:1994 Blank detail specification for the preparation of Customer Detail Specifications (CDS) and Detail Specifications for Standard Production Items with Capability Approval, prepared by CECC/WG22 “RF Connectors” and published by the European Committee for Electrotechnical Standardization (CENELEC
7、) Electronic Components Committee (CECC). This standard lists the ratings, characteristics and inspection requirements which shall be included as mandatory requirements in any detail specification for this type of connector. Detail specifications shall conform to the requirements of this blank detai
8、l specification and BS CECC00111 Rule of Procedure11. Specifications Part4:1991 Regulations for CECC detail specifications. The BritishStandard which implements the CECC Rules of Procedure is BS9000 General requirements for a system for electronic components of assessed quality Part2:1995 1)Specific
9、ation for the national implementation of the CECC system. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from le
10、gal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on
11、the inside front cover. Cross-references Publication referred to Corresponding BritishStandard CECC22000-II BS CECC22000:1993 Harmonized system of quality assessment for electronic components. Generic specification. Radio frequency coaxial connectors (PartII) CECC00109 BS CECC00109:1991 Rule of Proc
12、edure9. Certified test records IEC96 BS2316 Specification for radio frequency cables 1) In preparationEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN122003 January 1994 UDC Supersedes CECC22003 Issue1:1993 Descriptors: Quality, electronic components, connectors English version Blank Detail Spec
13、ification for the Preparation of Customer Detail Specifications (CDS) and Detail Specifications for Standard Production Items with Capability Approval Spcification particulire cadre pour la prparation de spcifications particulires client (CDS) et spcifications particulires pour desproduits standard
14、sous agrment de savoir-faire Vordruck fr Bauartspezifikation zur Erstellung von Kundenbauart-spezifikationen (CDS) sowie Bauartspezifikationen fr Standard-Produkte mit Befhigungsanerkennung This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on26 December1993. C
15、ENELEC members are bound to comply with CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap
16、plication to the General Secretariat of the CECC or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CE
17、CC General Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United
18、 Kingdom. The membership of the CECC is identical, with the exception of the national electrotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische N
19、ormung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to CENELEC members Ref.No.EN122003:1994EEN122003:1994 BSI 12-1999 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical
20、 Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the gran
21、t of an internationally recognized Mark, or Certificate, of Conformity. The components produced under the System are thereby acceptable in all member countries without further testing. This European Standard was prepared by CECCWG22, “RF Connectors”. The text of the draft based on document CECC22003
22、 Issue1:1993 was submitted to the formal vote for conversion to a European Standard; together with the voting report, circulated as document CECC(Secretariat)3469 it was approved by CECC as EN122003 on26 December1993. The following dates were fixed: The CENELEC Electronic Components Committee (CECC)
23、 is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specif
24、ications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate of Conformity. The components produced under the System are thereby acceptable in all member countries without further testing. This specification has been for
25、mally approved by the CECC, and has been prepared for those countries taking part in the System who wish to issue national harmonized specifications for Radio Frequency Coaxial Connectors. It should be read in conjunction with the current regulations for the CECC System. At the date of printing of t
26、his specification, the member countries of the CECC are Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom, and copies of it can be obtained from the addresses shown on the blue fly sheet. Preface
27、This specification was prepared by CECC WG22 “RF Connectors”. It is based, wherever possible, on the Publications of the International Electrotechnical Commission. The text of this specification was circulated to the CECC for voting as Annex E of the document indicated below, and was ratified by the
28、 President of the CECC for printing as a CECC Specification. latest date of announcement of the EN at national level (doa)1994-05-02 latest date of publication ofan identical national standard a (dop)1994-11-02 latest date of withdrawal ofconflicting national standards a (dow)1995-11-02 a National S
29、tandard (excluding National implementation of IECQ Specifications) Document Date of voting Report on the voting CECC(Secretariat)2708December1990 CECC(Secretariat)2819EN122003:1994 BSI 12-1999 3 The front page of the BDS is designed to allow use for either customer detail Specifications or for detai
30、l specifications covering standard production items. According to whether the DS is a customer detail specification or for standard production items, the non-applicable section at the top of the front page should be cancelled with heavy Z lines leaving 2 together with 5 and 6 and below intact. The i
31、nformation to be entered in the unnumbered boxes of the customer detail specification section is clearly indicated in each box. The numbers between the square brackets correspond to the following information which should be entered in the appropriate box. 1 The name of the National Standards Organiz
32、ation under whose authority the detail specification is published and, if applicable, the organization from whom the detail specification is available. 2 The number of the detail specification. In the case of standard production items the number will be allocated by the CECC General Secretariat. 3 T
33、he number and issue number of the CECC sectional specification, also the national reference, if different. 4 If different from the CECC number, the national number of the detail specification, date of issue and any further information required by the national system, together with any amendment numb
34、ers. 5 A brief description of the component or range of components. 6 Information on typical construction (if applicable). 7 An outline drawing with main dimensions which are of importance for interchangeability, and/or reference to the appropriate national/international document for outline. 8 Part
35、iculars of any variants covered by the DS. These could include as appropriate: cable types, (or sizes) applicable to each variant; alternative plated or protective finishes of the connector body and/or of the centre contact. 9 Details of the marking of the assembly and package. 10 Requirements for p
36、erformanceelectrical, mechanical, environmental, endurance and resistance to contaminating fluids and solvents. 11 Requirements for lot-by-lot quality conformance inspection together with details of any other specialized test/inspection requirements not covered by CECC22000-II.EN122003:1994 4 BSI 12
37、-1999 NOTE 1Information about manufacturers who have components qualified to this detail specifications available in the current CECC00200: Register of Approvals (Register of Firms, Products, and Services Approved under the CECC System). NOTE 2Delete whichever whole section is not applicable with he
38、avy Z lines leaving 2, 5 and 6 and below intact. NOTE 3The outline drawing provides main dimensions which are of importance for interchangeability, and/or reference to the appropriate national/international document for outlines. Alternatively these details may be given in an annex but 7 should alwa
39、ys contain an illustration of the general appearance of the assembly.EN122003:1994 BSI 12-1999 5 9 Marking of assembly and package (see1.5 of CECC22000-II) 10 Performance requirements (including limiting conditions of use) Ratings and characteristics Value Remarks Electrical Mechanical Environmental
40、 Endurance Resistance to contaminating fluids and solventsEN122003:1994 6 BSI 12-1999 11 Quality conformance requirementsTest groups A and B only unless otherwise stated NOTEEach Detail Specification shall state which tests are to be applied, the Inspection and Acceptable Quality Levels when applica
41、ble and the relevant minimum/maximum limits to be applied. Sub-group and test CECC22000 Clause 100% Inspection Limits IL AQL Min. Max. Sub-group A0 100% Visual inspection Sub-group A1 Sub-group B1 Any other specialized test requirement shall be entered here:blankBS EN 122003:1995 BSI 389 Chiswick Hi
42、gh Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendmen
43、t or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would i
44、nform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standa
45、rds. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publishe
46、d as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which
47、 give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits c
48、ontact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no
49、 extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is