1、September 2008DEUTSCHE NORM English price group 14No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.220.10; 23.080!$R
2、,/“1470912www.din.deDDIN EN 1028-1Fire-fighting pumps Fire-fighting centrifugal pumps with primer Amendment A1:2008)English version of DIN EN 1028-1:2008-09Feuerlschpumpen Feuerlschkreiselpumpen mit Entlftungseinrichtung A1:2008)Englische Fassung DIN EN 1028-1:2008-09SupersedesDIN EN 1028-1:2002-11w
3、ww.beuth.dePart 1: Classification General and safety requirements (includesTeil 1: Klassifizierung Allgemeine und Sicherheitsanforderungen (enthlt nderungDocument comprises 34 pages DIN EN 1028-1:2008-09 2 Start of validity This standard takes effect on 1 September 2008. DIN EN 1028-1:2002 may be us
4、ed in parallel until December 2008. National foreword This standard includes safety requirements. This standard has been prepared by Technical Committee CEN/TC 192 “Fire service equipment” (Secretariat: BSI, United Kingdom), Working Group WG 2 “Fire-fighting pumps” (Secretariat: DIN, Germany). This
5、document includes Amendment A1:2008. The responsible German body involved in its preparation was the Normenausschuss Feuerwehrwesen (Firefighting and Fire Protection Standards Committee), Technical Committee NA 031-04-05 AA Feuerlsch-pumpen. Amendment A1:2008 to EN 1028-1:2002 was necessary for the
6、following reasons: Due to the revision of the Machinery Directive 98/37/EC and its replacement through 2006/42/EC, effective from 29 December 2009, modifications to the European Standards cited under that Directive in the Official Journal of the European Communities have been necessary. If these mod
7、ifications had not been made, then an Annex Z would have been added to the relevant standard stating that the standard does NOT comply with the relevant essential requirements of Directive 2006/42/EC. The standard would have then been deleted from the Official Journal and would have no longer been d
8、eemed a harmonized standard. To maintain its status as a harmonized standard, EN 1028-1:2002 has been carefully reviewed and compared with the revised Machinery Directive 2006/42/EC; it has been determined that the standard complies with the requirements of 2006/42/EC. Therefore, CEN/TC 192 decided
9、in June 2007 to use the “simple amendment” (type 1) procedure which does not involve any technical modifications, but only a few minor editorial changes (e.g. updating the Foreword) and the addition of a new Annex ZB. Amendment A1:2008, in conjunction with EN 1028-1:2002 thus concretizes the basic r
10、equirements set out in Annex I of the EU Machinery Directive 98/37/EC (valid until 28 December 2009) and the new Machinery Directive 2006/42/EC which becomes applicable on 29 December 2009 relating to machines to be placed on the EEA market, with the intent of simplifying the means of proving confor
11、mity with such requirements. Once this standard is designated a harmonized standard in the Official Journal of the European Union, a manufacturer applying this new consolidated version of the standard may assume compliance with the requirements of the Machinery Directive (the so-called “presumption
12、of conformity”). A revision of Part 2 of EN 1028 (EN 1028-2:2002) was also necessary for the same reasons. This European Standard is to be applied in conjunction with Part 2 of EN 1028 Verification of general and safety requirements. The 2002 edition of this European Standard, together with EN 1028-
13、2, replaced the German standards specifying requirements for and the testing of pumps for fire-brigades, DIN 14420-1:1986-02 and DIN 14420-2:1989-04. Because these two national standards had to be withdrawn upon the publication of the European Standards, a “residual standard” was published as DIN 14
14、420 containing national provisions not covered by the European Standard but which are necessary for the application of DIN EN 1028 in Germany. The DIN collective mark may be applied to pumps complying with this standard if they have been registered by DIN CERTCO. NOTE 1 Use of the collective mark re
15、quires registration by DIN CERTCO Gesellschaft fr Konformittsbewertung mbH, Alboinstr. 56, 12103 Berlin. DIN EN 1028-1:2008-09 3 NOTE 2 is a registered trademark of DIN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall no
16、t be held responsible for identifying any or all such patent rights. Below is a description of how to designate the DIN 14420-2 fire-fighting centrifugal pumps previously used in Germany while observing the requirements of this European Standard: The designation Fire-fighting centrifugal pump EN 102
17、8-1 FPN 10 750 is recommended as a replacement for the designation of the fire-fighting centrifugal pump FP 8/8 as in DIN 14420-2; Fire-fighting centrifugal pump EN 1028-1 FPN 10 1 500 is recommended as a replacement for the designation of the fire-fighting centrifugal pump FP 16/8 as in DIN 14420-2
18、; Fire-fighting centrifugal pump EN 1028-1 FPN 10 2 000 is recommended as a replacement for the designation of the fire-fighting centrifugal pump FP 24/8 as in DIN 14420-2. The DIN Standards corresponding to the International Standards referred to in clause 2 and in the bibliography of the EN are as
19、 follows: EN ISO 9905 DIN ISO 9905 EN ISO 9908 DIN ISO 9908 ISO 3864 replaced by ISO 3864-1 (identical with DIN 4844-1) and ISO 7010 (no corresponding national standard available) Amendments This standard differs from DIN EN 1028-1:2002-11 as follows: a) Requirements regarding marking have been modi
20、fied, particularly the required information (11.4.1). b) Annex ZA (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC” has been editorially revised. c) Annex ZB (informative) “Relationship between this European Standard and the Essential
21、 Requirements of EU Directive 2006/42/EC” has been included. Previous editions DIN FEN 103 = DIN 14581: 1935-10 DIN 14420: 1957-08, 1961-06 DIN 14420-1: 1979-08, 1986-02 DIN 14420-2: 1979-08, 1981-09, 1986-08, 1989-04 DIN EN 1028-1: 2002-11 DIN EN 1028-1:2008-09 4 National Annex NA (informative) Bib
22、liography DIN 4844-1, Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs in workplaces and public areas DIN 14420, Fire-fighting pumps Fire-fighting centrifugal pumps Requirements for the suction-sided and pressure-sided assembly, test after installation in
23、the fire-fighting vehicle DIN ISO 9905, Technical specifications for centrifugal pumps Class I DIN ISO 9908, Centrifugal pumps Technical specifications for centrifugal pumps Class III EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1028-1:2002+A1 July 2008 ICS 13.220.10 Supersedes EN 1028-1:200
24、2 English Version Fire-fighting pumps - Fire-fighting centrifugal pumps with primer Pompes usage incendie - Pompes centrifuges usage Classification - Prescriptions gnrales et de scurit Feuerlschpumpen - Feuerlschkreiselpumpen mit Entlftungseinrichtung - Teil 1: Klassifizierung - Allgemeine und Siche
25、rheitsanforderungen This European Standard was approved by CEN on 8 April 2002 and includes Amendment 1 approved by CEN on 6 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national
26、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any o
27、ther language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Eston
28、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROP
29、ISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1028-1:2002+A1:2008: Eincendie avec dispositif damorage - Partie 1: - Part 1: Classification - Ge
30、neral and safety requirements EN 1028-1:2002+A1:2008 (E) Contents Foreword4 0 Introduction 5 1 Scope 6 2 Normative references 7 3 Terms and definitions .8 3.1 Pumps and their applications.8 3.2 Suction heights9 3.3 Pressures9 3.4 Delivery rates11 3.5 Power 11 3.6 Speed of rotation .12 3.7 Efficienci
31、es .12 4 List of significant hazards 12 5 Safety requirements and/or protective measures14 5.1 General14 5.2 Special requirements 15 5.2.1 Mechanical hazards.15 5.2.2 Electrical hazards 16 5.2.3 Thermal hazards 16 5.2.4 Hazards from neglecting ergonomic design principles 17 5.2.5 Hazards due to brea
32、kdown and/or incorrect installation of protection devices.17 6 General and performance requirements .18 6.1 Design .18 6.2 Materials .18 6.3 Nominal delivery pressure18 6.4 Nominal delivery rate 18 6.5 Geodetic nominal suction height.18 6.6 Closing pressure18 6.7 Primer19 6.8 Drainability .19 6.9 Sh
33、ut off valves and pump connections.19 6.10 Pump inlet screen19 6.11 Low temperature starting19 6.12 Very low temperature behaviour19 6.13 Operating controls.19 6.14 Additional equipment 19 6.15 Pump integrity protection equipment19 6.16 Efficiency 20 6.17 Guarantee points .20 6.18 Special tools.20 7
34、 Verification of the safety requirements and/or protective measures.20 8 Verification of the general and performance requirements 20 9 Classification and brief designation21 10 Designation 22 11 Information for use 22 11.1 General22 11.2 Signals and warning devices22 11.3 Accompanying documents.22 1
35、1.3.1 General22 Page2DIN EN 1028-1:2008-09 EN 1028-1:2002+A1:2008 (E) 11.3.2 Contents .22 11.4 Marking .27 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC“.28 Annex ZB (informative) !Relationship between this European Standa
36、rd and the Essential Requirements of EU Directive 2006/42/EC“.29 Bibliography30 3 DIN EN 1028-1:2008-09 EN 1028-1:2002+A1:2008 (E) Foreword This document (EN 1028-1:2002+A1:2008) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment“, the secretariat of which is held by BSI. Th
37、is European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. This document includes Amendment 1, approved by CEN
38、 on 2008-06-06. This document supersedes EN 1028-1:2002. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports
39、 essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ This part of this European Standard shall be applied only in conjunction with part 2 of EN 1028 “Verification of general and safety requi
40、rements“. EN 1028 “Fire-fighting pumps Fire-fighting centrifugal pumps with primer“ comprises two parts: Part 1: Classification General and safety requirements; Part 2: Verification of general and safety requirements. According to the CEN/CENELEC Internal Regulations, the national standards organiza
41、tions of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman
42、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 4DIN EN 1028-1:2008-09 EN 1028-1:2002+A1:2008 (E) 0 Introduction This European Standard is a type C standard as stated in EN 292 and EN 1070. The machinery concerned and the extent to which hazards, hazardous situations and event
43、s are covered are indicated in the scope of this standard. Where provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been desig
44、ned and built in accordance with the provisions of this type C standard. This Standard has been prepared as a harmonized standard to provide one means of conformity with essential requirements of the Machinery Directive and associated EFTA Regulations. While producing this standard it was assumed th
45、at: a) only trained persons operate the machine; b) components without specific requirements are: 1) designed in accordance with the usual engineering practice and calculation codes, including all failure modes; 2) of sound mechanical construction; 3) of materials with adequate strength and of suita
46、ble quality; 4) of materials free of defects; NOTE General hazards due to hydraulic and pneumatic equipment are dealt with in standards for common use such as EN 982, EN 983. c) harmful materials (e.g. asbestos) are not used as part of the machine; d) components are kept in good repair and working o
47、rder, so that the required characteristics remain; e) by design of the load bearing elements, a safe operation of the machine is assured for loading, from 0 % to 100 % of the rated possibilities and during the tests; f) to ensure the correct functioning of the equipment, the ambient temperature is m
48、aintained between -15 C (for special conditions, -30 C; see 6.12) and 40 C; NOTE Directly around the pump the temperature can be 20 C higher. g) the manufacturer and the user have agreed the features of the machinery and the operating conditions; h) the place of installation enables safe usage of th
49、e machine. 5 DIN EN 1028-1:2008-09 EN 1028-1:2002+A1:2008 (E) 1 Scope This standard applies for centrifugal pumps with priming devices for fire-fighting use supplied separately without driver and couplings. Fire-fighting centrifugal pumps with primer are defined as terminated by their inlet and outlet connec-tions as well as by their shaft ends. This standard applies for fire-fighting centrifugal pumps with priming devices for use under ambient temperatures between -15 C and 40 C. NOTE For special conditions, -30
