1、pEEq A-A-55 196A July 26, 2000 SUPERCEDING 9 April 1993 A-A-55 196 COMMERCIAL ITEM DESCRIPTION COVERALLS, DISPOSABLE The General Services Administration has authorized the use of this Commercial Item Description in Preference to MIL-C-87069. 1. SCOPE. This Commercial Item Description covers the requ
2、irements for a disposable coverall of white, uncoated, spunbonded nonwoven olefin fabric, intended to be worn by civilian and military personnel working with asbestos and/or fibrous glass materials. 2. CLASSIFICATION. The disposable coveralls are furnished in the following types and sizes: Type I- W
3、ith hood Type II-Without hood NOTE: The sizes may be abbreviated as SM/MED, LG/XLG, and XXLG. 3. SALIENT CHARACTERISTICS 3.1 Description. The white disposable coveralls of uncoated, spunbonded nonwoven olefin fabric shall be a one piece step-in-sack type design with or without attached hood and draw
4、string face closure and double face pressure sensitive tape with removable protective covering adhered vertically to one edge of neck closure flap. There shall be no fly opening. Both types shall have a 3/4 to 1 inch drawcord tunnel along the entire circumference of the body at top of coverall that
5、serves as a body closure at the neck. The tunnel must stop and finish 1/2 inch from the center front to allow ends of drawcord to hang out. The coverall shall have tie tapes at waist and ankles and full length sleeves with elasticized wrists and attachecbootees. The hood for type I shall be two pane
6、ls stitched along the top and back, forming the center back seam. Around the face opening there is a 5/8 inch to 3/4 inch tunnel with an encloseddrawcord. Beneficial comments, (recommendations, additions, deletions) and any data which may be of use in approving this document should be addressed to:
7、Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-COCT, 700 Robbins Avenue, Philadelphia, PA 19111-5096. AMSC N/A FSC 8415 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55196A 3.1.1 Seams and stitching The seams
8、shall be formed by super-imposing two plies of material, folding both the edges back over the body of material and overedging or straight stitching. The stitches per inch shall be 6 to 8. The stitch gauge and stitch length shall produce adequately durable seams though out the garment. The overedged
9、side of the seam shall finish on the outside of the garment. 3.1.2 Drawcords. The hood drawcord, body drawcord, and leg and waist adjustment ties shall be made out of the basic fabric by folding lengthwise, turning under the edges and stitching 1/16 to 1/8 inch from the folded edge. The finished wid
10、th shall be 3/8 to 1/2 inch. When hood and body openings are fully extended, the ends of the drawcord shall extend a minimum of 7 inches beyond ends of the drawcord tunnels. The waist adjustment ties shall be cut 72 inches in length and the leg adjustment ties shall each be cut 28 inches in length.
11、3.2 Material. The basic material shall be white spunbonded (nonwoven), nonperforated (uncoated) olefin fabric. The Weight shall be l. 1-1.5 oz/sq yd. when tested in accordance with ASTM-D-3776. The minimum Breaking strength (Machine direction) shall be 5.5 pounds and the Cross direction shall be 8.1
12、 pounds when tested in accordance with ASTM-D-5035 3.3 Thread. The sewing thread shall be commercial type, suitable for the purpose intended. The color of the thread shall be white. 3.4 Elastic. The elastic used around the edges of the wrist shall be 3/8 inch in width, 6 inches in length and shall b
13、e either a cut rubber tape, or a woven, braided, or knitted elastic webbing. The color shall be gray, or natural or white. 3.5 Fastener Tape. The fastener tape used to close the neck portion of the hood, when applicable shall be 1/2 inch wide double faced pressure sensitive tape with removable prote
14、ctive covering. The tape shall be of any commercial type that is suitable for the purpose intended. 3.6 LabeUmarking The coveralls shall have a combination identification, size and cautionary statement label not less than 2 by 3 inches in size, bearing the information below. The inscription can be d
15、irectly marked on the material by direct printing, marking, stamping or stenciling or may be printed on a pressure-sensitive label that will adhere satisfactory to the coveralls and shall be placed approximately 2 inches below the top of the drawstring body closure. COVERALLS, DISPOSABLE CONTRACT NO
16、: STOCK NO: SIZE: NAME OF CONTRACTOR: CAUTION SHALL NOT BE WORN IN HOT WORK AREAS 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55196A Note: The cautionary statement shall be printed in larger letters than all other lettering on the label. 3.
17、7 Patterns. The government shall furnish a complete set of patterns or a master pattern with grade rules, to maintain uniformity and consistency in manufacturing. The government patterns shall be used to create the contractors working patterns. Minor modifications are permitted to accommodate manufa
18、cturing procedures, however the design and finished measurements shall be maintained. TABLE I. Pattern Parts Nomenclature Body Sleeves Bootees 11 Cut Pieces 2 4 14 Type I only Hood 1 Tunnel 2 - 11 May be cut in one piece so seam is on the inside of foot in lieu of heel. 3.8 Sizes and Measurements Th
19、e finished coveralls shall conform to the measurements below. All measurements and tolerances are expressed in inches. TABLE II. Measurements 32-118 4 1-318 33-318 Tolerance I -1/2,+ 1 I -1/2,+ 1 1+1 - I -1/2,+ 1 Sizes Hood Length (G) Bootee (F) Bootee depth (E) length (type I only) SWMD 22-314 16-3
20、18 5-118 LGIXLG 22-314 17 5-118 XXLG 22-314 17-318 5-118 A. Chest- Measure from one inch below the base of the armhole across the chest from folded B. Sleeve length- Measure straight from center of back at hood joining seam to bottom of C. Body length- Measure from intersection of front seam and cen
21、ter of crotch seam to top of D. Leg inseam Measure from the center of the crotch seam to the bottom seam of the bootee edge to folded edge. sleeve. front opening. cover. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55196A E. Bootee depth- Me
22、asure from top seam to bottom seam of bootee. F. Bootee length- Measure from front seam to back seam ofbootee. G. Hood length- Measure from midpoint of hood body seam to top of hood seam. 3.9 Labelhag. Each item shall be individually bar-coded with a tag for personal clothing items. The non-permanen
23、t tags shall be attached to each item, and shall be clearly legible and readable by a scanner. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type shall be a medium to high code density and shall be located so that it is completely visible on the item when it is
24、 folded and/or packaged as specified. 4. REGULATORY REQUIREMENTS 4. l. Recycled, recovered, or environmentally preferable materialsRecycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational an
25、d maintenance requirements, and promotes economically advantages life cycle costs. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product Conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards and quality assurance
26、 practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.1.2 Visual examination Each coverall shall be examined for the defects listed below: Material defects Cloth-Any hole, cut, tear, mend, burn, needle
27、 chew, any imbedded foreign matter; overall uncleanness; objectionable odor. Seams and stitching -End of stitching not caught in other seams or not securely -Pleated or puckered seam -Stitching excessively loose or tight -Thread breaks not securely overstitched for a 1/2 inch distance -Open seam mor
28、e than 1 inch -Open seam less than 1 inch backstitched Dimensions -Measurement of item not as specified Labels -Any information illegible, incorrect, incomplete, or missing Maior 101 102 103 104 105 106 107 20 1 202 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
29、se from IHS-,-,-A-A-55196A 5.2 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order. 6. PACKAGING 6.1 Preservation, packing, and marking The preservation, packing, and marking will be as specified in the contract or order. 7. NOTES 7.1 Source of Government
30、 documents. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19 1 1 1-5094 MILITARY INTERESTS: CUSTODIANS Navy - NU REVIEW Navy - SH CIVIL AGENCY COORDINATING ACTIVITY ACTIVITY: GSA - FSS PREPARING ACTIVITY
31、: DLA - CT (Project number 84 15- O 185 ) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55196A COVERALLS, DISPOSABLE NOTE: HOOD NOT APPLICABLE TO TYPE II COVERALL FIGURE 1- COVERALLS, DISPOSABLE 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55196A FIGURE 2- HOOD AND DRAWCORD CLOSURE 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
