1、PREPAREDBY Jeffery Bohannon CHECKED BY George Mc Cann APPROVED BY Richard Marbais CAGE CODE IZE 1 03723 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 TITLE ADAPTER, CONNECTOR, GENERAL DRAWING FOR DWG. NO. 85025 PAGE 1 OF 5 5935-E642 Provided by IHSNot for ResaleNo reproduction or network
2、ing permitted without license from IHS-,-,-1. SCOPE 1.1 Scope. This drawing covers the general requirements for radiofrequency adapters for use with various test equipment. 1.2 Part or Identifvina Number (PIN). The complete PIN shall be as specified on the item requirements drawing and constructed u
3、sing the following format: 85XXX -X DSCC -1.50R impedance requirement drawing -2.752 impedance (1.2.1) 1.2.1 DSCC reauirements drawinq. The DSCC requirements drawing shall state the requirement values and design modifications required of the connectors to be procured by the Government. 2. APPLICABLE
4、 DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Depa
5、rtment of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-55469 L-P-41 O QQ-N-290 - Nickel Plating (Electrodeposited). - Connectors, Electrical, Plugs, TIP (Test Point Plug, Banana Plug) General Requiremen
6、ts For. - Plastic, Polyamide (Nylon), Ridge, Rods, Tubes, Flats, Molded and Cast Parts. STANDARDS FEDERAL FED-STD-595 - Color Used in Government Procurement. DEPARTMENT OF DEFENSE MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-1344 - Test Methods for Electrical Con
7、nectors. (Unless otherwise indicated, copies of the above specifications, standards and handbooks are available from the Defense Printing Service Detachment Office, Building 4D, Customer Service, 700 Robbins Avenue, Philadelphia, PA 191 11 -5094.) CAGE CODE DWG NO. 03723 85025 A DEFENSE SUPPLY CENTE
8、R, COLUMBUS COLUMBUS, OH 4321 6-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I 2.2 Non-Government Dublications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the
9、 documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation. American Society for Testing and Materials (ASTM) ASTM B139
10、ASTM 8194 ASTM B196 ASTM B197 ASTM B488 ASTM D171 O ASTM 841 O1 ASTM D4673 ASTM D5948 - Phosphor Bronze Rod, Bar, and Shapes. - Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar. - Copper-Beryllium Alloy Rod and Bar. - Copper-Beryllium Alloy Wire. - Electrodeposited Coatings of Gold for Eng
11、ineering Uses. - Extruded and Compression Molded Polytetrafluoroethylene (PTFE) Rod and Heavy Walled Tubing. - Standard Specification for Propylene Plastic Injection and Extrusion Material. - Molding and Extrusion Materials, Acrylonitrile-Butadiene-Styrene (ABS), Plastics and Alloys. - Compounds, Mo
12、lding, Thermosetting. (Application for copies should be addressed to American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) SOCIETY OF AUTOMOTIVE ENGINEERS, INC. SAE AMs-QQ-P-35 - Passivation Treatment for Corrosion-Resistant Steel. (Applications for co
13、pies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrandale, PA 15096-0001 .) 3. REQUIREMENTS 3.1 DSCC requirements drawinq. The individual item requirements shall be in accordance with A-A-55469 except as specified in the requirements drawing and herein. In c
14、ase of conflict between this drawing and requirements drawing, the latter shall govern. 3.2 Desian, construction, and Dhvsical dimensions. The design, construction, and physical dimensions shall be as specified in A-A-55469 except as specified in the requirements drawing and herein. 3.2.1 Desicm doc
15、umentation. The design documentation shall be in accordance with A-A-55469 and, unless otherwise specified in the acquisition document, shall be retained by the manufacturer but be available for review by the contracting activity or contractor upon request. 3.3 Materials. Materials shall be as speci
16、fied herein; however, when a definite material is not specified, a material shall be used which will enable the connectors to meet the performance requirements of this specification. Acceptance or approval of any constituent material shall not be construed as a guaranty of the acceptance of the fini
17、shed product. 3.3.1 Metals and finishes. All exposed metal parts, except electric contacts, terminals, and corrosion-resisting steel parts shall be nickel-plated in accordance with class 1, type 2, of QQ-N-290. Steel parts shall be passivated in accordance with SAE-AMs-QQ-P-35. 3.3.2 Contacts. Conta
18、cts and contact tabs shall be made of copper-beryllium in accordance with ASTM B196, ASTM B197,and ASTM 8194, or (when specified in 3.1) phosphor bronze in accordance with ASTM 8139. Contacts shall be gold plated in accordance with ASTM 8488, type 3, grade C, and class 1.27 (50p inch). Silver underp
19、late shall not be used. 3.3.3 Plastic parts. Plastic parts shall be made in accordance with ASTM D5948, ASTM D171 O, L-P-41 O, ASTM D4101, or ASTM D4673 unless otherwise specified (see 3.1). The color of the insulated portions shall be black number 17038 or red number 11 136 in accordance with FED-S
20、TD-595, as specified (see 3.1). 3.4 Electrical Derformance characteristics. The electrical performance characteristics are as specified in table I and the requirements drawing and apply over the entire operating temperature unless otherwise specified. CAGE CODE DWG NO. 03723 85025 A DEFENSE SUPPLY C
21、ENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical performance characteristics. i 5,000 M ohms Inspection Requirement value Inspection 3.5 Markinq. Marking shall be in accordance with A-A-55469
22、 except the PIN shall be in accordance with 1.2 herein. 3.6 Environmental and mechanical performance characteristics. The environmental and mechanical performance characteristics are as specified in table II. Requirement value 3.6.1 Vibration. When connectors are tested as specified in 4.4, there sh
23、all be no loss of electrical continuity in excess of 10 microseconds during the test. After the test, connectors shall meet the following requirements: Visual examination: There shall be no cracking, breaking, or loosening of parts or other evidence of physical damage. TABLE II. Environmental and me
24、chanical performance characteristics. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 CAGE CODE DWG NO. SIZE 03723 85025 REV A PAGE 4 A Corrosion Durability 48 hours, 5% salt solution (MIL-STD-202, method 101, test condition B) 500 cycles 3.7 Qualifications. Qualification inspection for conn
25、ectors Specified herein shall not be required. 3.7.1 Qualitv conformance inspection. The quality conformance inspection shall be in accordance with A-A-55469 and 4.3 herein. 3.8 Manufacturer eliaibility. To be eligible to supply connectors to this drawing, a manufacturer must be capable of meeting t
26、he requirements specified herein and those of A-A-55469. 3.9 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source (see 6.5). 4. QUALITY ASSURANCE PROVISIONS 4.1 Samplina and inspection. Sampling and inspection proced
27、ures shall be in accordance with A-A-55469, except as modified herein. 4.2 Qualification inspection. Qualification inspection for connectors specified herein shall not be required. 4.3 Qualitv conformance inspection. Quality assurance inspection shall be in accordance with A-A-55469. 4.4 Vibration (
28、see 3.6.1). Connectors shall be tested in accordance with method 2005 of MIL-STD-1344. The following details shall apply: a. Test condition number 1. b. Measurement during test - Connectors shall be monitored for electrical continuity during the test. Equipment shall be sufficiently sensitive to det
29、ect any interruption with a duration of 1 O microseconds. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5. PACKAGING 5.1 Packaaina reauirements. The requirements for packaging shall be in accordance with A-A-55469. 6. NOTES 6.1 Intended use. Connec
30、tors conforming to this drawing are intended for use when military specifications do not exist and qualified military connectors that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate s
31、pecifications, drawings, and stock catalog listings. 6.2 Acquisition requirements. The acquisition documents should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery one copy of the quality conformance inspection data pertinent to the connector inspection lot, to be supp
32、lied with each shipment by the connector manufacturer, if applicable. c. Requirements for certificate of compliance, if applicable. d. Requirements for notification of change of product or process to procuring activity, if applicable. e. Requirements for packaging and packing (see 5.1). f. Requireme
33、nts for assembly and assembly tools. 6.3 Redaceability. Replaceability is determined as follows: a. Connectors covered by this drawing will replace the same generic connectors covered by a contractor-prepared specification b. When a QPL source is established, the part numbered connector specified in
34、 the requirement drawing will be replaced by the 6.4 Comments. Comments on this drawing should be directed to DSCC-VAI, 3990 E. Broad Street, Columbus, Ohio 43216-5000, or telephone (614) 692-0568. 6.5 Submission of certificate of corndiance. The certificate of compliance submitted to DSCC-VAI prior
35、 to listing as an approved source of supply, shall state that the manufacturers product meets the requirements of the applicable DSCC requirements drawing and stated herein. or drawing. connector in the requirement drawing supersession table. CAGE CODE DWG NO. 03723 85025 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4321 6-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
