1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add irridite finish reference to MIL-C-5541. Change threads to stainless steel inserts. 5 AUG 1988 Randy Larson B Replaced canceled documents and changed FSC. Editorial changes throughout. 31 DEC 2003 Thomas M. Hess Prepared in accordance with ASME Y14.100
2、Selected item drawing REV PAGE REV PAGE REV STATUS REV B B B B B B B B B B OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Frank A. Crivello DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 http:/www.dscc.dla.mil Original date of drawing 15 July 1985 CHECKED BY Randy
3、Larson TITLE SUPPORT, ELECTRICAL CARD HOLDER, APPROVED BY Ivan R. Jones MOUNTING BAR SIZE A CODE IDENT. NO. 14933 DWG NO. 85075 REV B PAGE 1 OF 10 AMSC N/A 5998-E043 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGIS
4、TICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawin
5、g describes the requirements for a family of mounting bars intended for use with card guides described in DSCC drawing 85076. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85075 Drawing number 010 Dash number (see table I) N Finish (A or N) (see 3.3.1) 2. APPLICABLE DOC
6、UMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ens
7、ure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. The following specifications, standards, and handbooks form a part
8、 of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-S-5002 Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems. MIL-C-5541 Chem
9、ical Conversion Coatings On Aluminum And Aluminum Alloys. DEPARTMENT OF DEFENSE STANDARDS MILSTD1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order
10、 Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract. ASTM IN
11、TERNATIONAL (ASTM) ASTM B36 - Standard Specification for Brass Plate, Sheet, Strip, and Rolled Bars. (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, P.O. Box C700, West Coshohocken, PA 19428-2959 or at URL: http:/www.astm.org.) SOCIETY OF AU
12、TOMOTIVE ENGINEERS (SAE) SAE AMS-QQ-A-200/9 Aluminum Alloy 6063, Bar, Rod, Shapes, Tube, and Wire, Extruded. SAE AMS-QQ-A-250/8 Aluminum Alloy 5052, Plate and Sheet. SAE AMS 5525 Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 Degrees
13、F (982 Degrees C) Solution Heat Treated. (Application for copies should be addressed to the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or at URL: http:/www.sae.org.) (Non-Government standards and other publications are normally available from the organizations which pr
14、epare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT
15、NO. 14933 DWG NO. 85075 REV B PAGE 3 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exem
16、ption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified in table I and on figure 1. 3.1.1 Installation torque. The recommended installation torque for fasteners into the threaded insert is 6 inch-pounds (
17、0.7 N-m). 3.2 Materials. 3.2.1 Support bar. The support bar material shall be aluminum alloy in accordance with AMS-QQ-A-200/9 or AMS-QQ-A-250/8. 3.2.2 Insert. The insert material shall be stainless steel in accordance with AMS 5525 or brass in accordance with ASTM B36. 3.3 Finish. 3.3.1 Support bar
18、. The support bar shall be irridite finish in accordance with MIL-C-5541, class 1A or supplied with no finish applied. Support bars with a chemical film finish shall include a suffix “A” in the PIN. Mounting bars with no finish shall include a suffix “N” in the PIN (see 1.2). 3.3.2 Insert. When the
19、insert is constructed of stainless steel, it shall be passivated in accordance with MIL-S-5002. FIGURE 1. Dimension and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO
20、. 14933 DWG NO. 85075 REV B PAGE 4 Inches mm Inches mm Inches mm Inches mm Inches mm .010 .030 .065 0.25 0.76 1.65 .095 .125 .138 .174 2.41 3.18 3.51 4.42 .187 .206 .250 .310 4.75 5.23 6.35 7.87 .348 .40 .400 .412 8.84 10.2 10.16 10.47 .430 .620 1.074 10.92 15.75 27.28 NOTES: 1. Dimensions are in in
21、ches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .010 inch (0.25 mm) for three place decimals and .02 (0.5 mm) for two place decimals. 3. See table I for dimension L values. 4. The recommended installation torque for fasteners into the th
22、readed insert is 6 inch-pounds (0.7 N-m). FIGURE 1. Dimension and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 5 TABLE I.
23、Length dimensions. 1/ 2/ PIN 85075 Configuration A PIN 85075 Configuration A Dimension “L” Dimension “L” 001 4.00 ( 101 .6 ) 037 13.00 ( 330.2 ) 002 4.25 ( 108.0 ) 038 13.25 ( 336.6 ) 003 4.50 ( 114.3 ) 039 13.50 ( 342.9 ) 004 4.75 ( 120.7 ) 040 13.75 ( 349.3 ) 005 5.00 ( 127.0 ) 041 14.00 ( 355.6 )
24、 006 5.25 ( 133.4 ) 042 14.25 ( 362.0 ) 007 5.50 ( 139.7 ) 043 14.50 ( 368.3 ) 008 5.75 ( 146.1 ) 044 14.75 ( 374.7 ) 009 6.00 ( 152.4 ) 045 15.00 ( 381.0 ) 010 6.25 ( 158.8 ) 046 15.50 ( 393.7 ) 011 6.50 ( 165.1 ) 047 16.00 ( 406.4 ) 012 6.75 ( 171.5 ) 048 16.50 ( 419.1 ) 013 7.00 ( 177.8 ) 049 17.
25、00 ( 431.8 ) 014 7.25 ( 184.2 ) 050 17.50 ( 444.5) 015 7.50 ( 190.5 ) 051 18.00 ( 457.2 ) 016 7.75 ( 196.9 ) 052 18.50 ( 469.9 ) 017 8.00 ( 203.2 ) 053 19.00 ( 482.6 ) 018 8.25 ( 209.6 ) 054 19.50 ( 495.3 ) 019 8.50 ( 215.9 ) 055 20.00 ( 508.0 ) 020 8.75 ( 222.3 ) 056 21.00 ( 533.4 ) 021 9.00 ( 228.
26、6 ) 057 22.00 ( 558.8 ) 022 9.25 ( 235.0 ) 058 23.00 ( 584.2 ) 023 9.50 ( 241.3 ) 059 24.00 ( 609.6 ) 024 9.75 ( 247.7 ) 060 25.00 ( 635.0 ) 025 10.00 ( 254.0 ) 061 26.00 ( 660.4 ) 026 10.25 ( 260.4 ) 062 27.00 ( 658.8 ) 027 10.50 ( 266.7 ) 063 28.00 ( 711.2 ) 028 10.75 ( 273.1 ) 064 29.00 ( 736.6 )
27、 029 11.00 ( 279.4 ) 065 30.00 ( 762.0 ) 030 11.25 ( 285.8 ) 066 31.00 ( 787.4 ) 031 11.50 ( 292.1 ) 067 32.00 ( 812.8 ) 032 11.75 ( 298.5 ) 068 33.00 ( 838.2 ) 033 12.00 ( 304.8 ) 069 34.00 ( 863.6 ) 034 12.25 ( 311.2 ) 070 35.00 ( 889.0 ) 035 12.50 ( 317.5 ) 071 36.00 ( 914.4 ) 036 12.75 ( 323.9 )
28、 See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 6 TABLE I. Length dimensions Continued. 1/ 2/ PIN 85075 Configuration B PI
29、N 85075 Configuration B Dimension “L” Dimension “L” 072 4.00 ( 101 .6 ) 108 13.00 ( 330.2 ) 073 4.25 ( 108.0 ) 109 13.25 ( 336.6 ) 074 4.50 ( 114.3 ) 110 13.50 ( 342.9 ) 075 4.75 ( 120.7 ) 111 13.75 ( 349.3 ) 076 5.00 ( 127.0 ) 112 14.00 ( 355.6 ) 077 5.25 ( 133.4 ) 113 14.25 ( 362.0 ) 078 5.50 ( 13
30、9.7 ) 114 14.50 ( 368.3 ) 079 5.75 ( 146.1 ) 115 14.75 ( 374.7 ) 080 6.00 ( 152.4 ) 116 15.00 ( 381.0 ) 081 6.25 ( 158.8 ) 117 15.50 ( 393.7 ) 082 6.50 ( 165.1 ) 118 16.00 ( 406.4 ) 083 6.75 ( 171.5 ) 119 16.50 ( 419.1 ) 084 7.00 ( 177.8 ) 120 17.00 ( 431.8 ) 085 7.25 ( 184.2 ) 121 17.50 ( 444.5) 08
31、6 7.50 ( 190.5 ) 122 18.00 ( 457.2 ) 087 7.75 ( 196.9 ) 123 18.50 ( 469.9 ) 088 8.00 ( 203.2 ) 124 19.00 ( 482.6 ) 089 8.25 ( 209.6 ) 125 19.50 ( 495.3 ) 090 8.50 ( 215.9 ) 126 20.00 ( 508.0 ) 091 8.75 ( 222.3 ) 127 21.00 ( 533.4 ) 092 9.00 ( 228.6 ) 128 22.00 ( 558.8 ) 093 9.25 ( 235.0 ) 129 23.00
32、( 584.2 ) 094 9.50 ( 241.3 ) 130 24.00 ( 609.6 ) 095 9.75 ( 247.7 ) 131 25.00 ( 635.0 ) 096 10.00 ( 254.0 ) 132 26.00 ( 660.4 ) 097 10.25 ( 260.4 ) 133 27.00 ( 658.8 ) 098 10.50 ( 266.7 ) 134 28.00 ( 711.2 ) 099 10.75 ( 273.1 ) 135 29.00 ( 736.6 ) 100 11.00 ( 279.4 ) 136 30.00 ( 762.0 ) 101 11.25 (
33、285.8 ) 137 31.00 ( 787.4 ) 102 11.50 ( 292.1 ) 138 32.00 ( 812.8 ) 103 11.75 ( 298.5 ) 139 33.00 ( 838.2 ) 104 12.00 ( 304.8 ) 140 34.00 ( 863.6 ) 105 12.25 ( 311.2 ) 141 35.00 ( 889.0 ) 106 12.50 ( 317.5 ) 142 36.00 ( 914.4 ) 107 12.75 ( 323.9 ) See notes at end of table. Provided by IHSNot for Re
34、saleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 7 TABLE I. Length dimensions Continued. 1/ 2/ PIN 85075 Configuration C PIN 85075 Configuration C Dimension “L” Dimension “L” 1
35、43 4.00 ( 101 .6 ) 179 13.00 ( 330.2 ) 144 4.25 ( 108.0 ) 180 13.25 ( 336.6 ) 145 4.50 ( 114.3 ) 181 13.50 ( 342.9 ) 146 4.75 ( 120.7 ) 182 13.75 ( 349.3 ) 147 5.00 ( 127.0 ) 183 14.00 ( 355.6 ) 148 5.25 ( 133.4 ) 184 14.25 ( 362.0 ) 149 5.50 ( 139.7 ) 185 14.50 ( 368.3 ) 150 5.75 ( 146.1 ) 186 14.7
36、5 ( 374.7 ) 151 6.00 ( 152.4 ) 187 15.00 ( 381.0 ) 152 6.25 ( 158.8 ) 188 15.50 ( 393.7 ) 153 6.50 ( 165.1 ) 189 16.00 ( 406.4 ) 154 6.75 ( 171.5 ) 190 16.50 ( 419.1 ) 155 7.00 ( 177.8 ) 191 17.00 ( 431.8 ) 156 7.25 ( 184.2 ) 192 17.50 ( 444.5) 157 7.50 ( 190.5 ) 193 18.00 ( 457.2 ) 158 7.75 ( 196.9
37、 ) 194 18.50 ( 469.9 ) 159 8.00 ( 203.2 ) 195 19.00 ( 482.6 ) 160 8.25 ( 209.6 ) 196 19.50 ( 495.3 ) 161 8.50 ( 215.9 ) 197 20.00 ( 508.0 ) 162 8.75 ( 222.3 ) 198 21.00 ( 533.4 ) 163 9.00 ( 228.6 ) 199 22.00 ( 558.8 ) 164 9.25 ( 235.0 ) 200 23.00 ( 584.2 ) 165 9.50 ( 241.3 ) 201 24.00 ( 609.6 ) 166
38、9.75 ( 247.7 ) 202 25.00 ( 635.0 ) 167 10.00 ( 254.0 ) 203 26.00 ( 660.4 ) 168 10.25 ( 260.4 ) 204 27.00 ( 658.8 ) 169 10.50 ( 266.7 ) 205 28.00 ( 711.2 ) 170 10.75 ( 273.1 ) 206 29.00 ( 736.6 ) 171 11.00 ( 279.4 ) 207 30.00 ( 762.0 ) 172 11.25 ( 285.8 ) 208 31.00 ( 787.4 ) 173 11.50 ( 292.1 ) 209 3
39、2.00 ( 812.8 ) 174 11.75 ( 298.5 ) 210 33.00 ( 838.2 ) 175 12.00 ( 304.8 ) 211 34.00 ( 863.6 ) 176 12.25 ( 311.2 ) 212 35.00 ( 889.0 ) 177 12.50 ( 317.5 ) 213 36.00 ( 914.4 ) 178 12.75 ( 323.9 ) 1/ Dimensions are in inches. Metric equivalents, in parenthesis, are given for general information only.
40、2/ Unless otherwise specified, tolerances are .004 per inch (0.10 mm) for length only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 8 3.4 Certifica
41、te of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.4.1 Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu o
42、f the manufacturer performing the inspection of product for delivery tests (see 4.1.2 and 6.2.b). 3.5 Marking. Marking of the mounting bar is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers
43、name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the opera
44、tional and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Mounting bards shall be free of flash, pits, voids, cracks, and excessive mold marks. A visible parting line is acceptable. 4. VERIFICATION 4.1 Conformance inspections. 4.1.1 Inspection of
45、product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of design and dimensions (see 3.1), materials (see 3.2), finish (see 3.3), and workmanship (see 3.7). Criteria for defects are listed in 4.1.5. 4.1.2 Optional statement of compliance. The acqu
46、iring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects ar
47、e found, the lot shall be rejected. Criteria for defects are listed in 4.1.5. TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 and over 29 35
48、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85075 REV B PAGE 9 4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out t
