1、REVISIONS LTR DESCRIPTION DATE APPROVED A Delete “part number” and substitute “Part or Identifying Number (PIN)”. Vendor CAGE 60563, PIN, delete and substitute new PIN. Editorial changes throughout. 01-01-22 Robert M. Heber B Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 test
2、procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV B A A B B REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Charles W. Koeller CON
3、NECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, SEVEN SIZE 20 SIGNAL CONTACTS, WITH SIX SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO. 89078 Original date of drawing 31 July 1990 A REV B PAGE 1 OF 5 AMSC N/A 5935-E773-000 Provided by IHSNot for ResaleNo reproduction or networking permitted
4、 without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm Inches mm .056 1.42 .652 16.56.093 2.36 .702 17.96 .112 2.84 .761 19.33.172 4.37 .815 20.70 .358 9.09 .870 22.10.437 11.10 .888 22.56 .623 15.82 .924 23.47 .978 24.84NOTES: 1. Dimensions are in inches. 2. Metric equiv
5、alents are given for information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a 0.005 (0.13 mm) diameter circle. 6. Markings are shown for the pin insert f
6、ront. Socket inserts are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. 037Z3 89078 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 FIGURE 1. Insert arrangement, seven size 20 signal contacts, with six size 8 contact cavity.
7、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55to +125C. REQUIREMENTS: (Requirements of drawing 85039 and MIL-DTL-24308 are applicable). D
8、imensions and configurations: See figure 1. Signal contact specifications: Style A: (crimp removable signal contacts) Socket: M39029/63-368. Pin: M39029/64-369. Style B: (solder fixed signal contacts) Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure B-2. Shell si
9、ze: Four. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designed for contact insertion and removal with the
10、applicable military tools as follows: Contact size Tool PIN 20 M81969/39-01 with plastic tip M81969/1-02 with metal tip 037Z3 89078 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S
11、IZE CAGE CODE DWG NO. Mating and unmating forces with signal contacts only installed (pounds): See table I. TABLE I. Mating and unmating forces. Mating Unmating Contact type min max min max Signal 0.270 4.6 0.270 2.7 Contact resistance: See table II. TABLE II Contact resistance (millivolts maximum).
12、 1/ Contact class G, D, M, N Contact size AWG Wire size Test current (amperes) After salt spray All other 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condit
13、ion All other conditions Sea level 70,000 ft 600 - 1,000 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 89078 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A
14、REVB PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to t
15、his drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 89078GBEPT 89078GBEST 89078GBEPR 89078GBESR DCMMY13W6PA101 DCMMY13W6SA101 DCMM13W6PA101 DCMM13W6SA101 P136PSA2D P136RSA2D P136PSA
16、2 P136RSA2 CBM13W6M02F00C-0 CBM13W6F02F00C-0 CBM13W6M02000C-0 CBM13W6F02000C-0 PCMMHW13W6P PCMMHW13W6S PCMMW13W6P PCMMW13W6S 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to
17、this drawing shall include a full compliment of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 and 89061. Vendor CAGE Vendor name number and address 28198 Positronics Industries, Incorpor
18、ated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 89078 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
