1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawi
2、ng YY-MM-DD CHECKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, DIGITAL-LINEAR, QUAD, DIFFERENTIAL LINE DRIVER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/07647 08-02-26 REV PAGE 1 OF 16 AMSC N/A 5962-V025-08 Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance quad differential line driver microcircuit, with an operati
4、ng temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/07647 - 01 X E Drawin
5、g Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 26C31-EP Quad differential line driver 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Packag
6、e style X 16 MS-012-AC Plastic surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IH
7、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to +7 V 2/ Input voltage range (VI). -0.5 V
8、 to VCC+ 0.5 V Differential input voltage range (VID) -14 V to 14 V Output voltage range (VO) . -0.5 V to +7 V Input or output clamp current (IIKor IOK) . 20 mA Output current (IO) . 150 mA VCCcurrent 200 mA GND current . -200 mA Package thermal impedance (JA) . 73C/W 3/ 4/ Operating virtual junctio
9、n temperature range (TJ) +150C Storage temperature range -65C to +150C 1.4 Recommended operating conditions. 5/ Supply voltage range (VCC) . 4.5 V to 5.5 V Differential input voltage (VID) 7 V nominal High level input voltage (VIH) . 2 V minimum Low level input voltage (VIL) . 0.8 V maximum High lev
10、el output current (IOH) . -20 mA maximum Low level output current (IOL) . +20 mA maximum Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional o
11、peration of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values, except differential output voltage (VOD) ar
12、e with respect to network ground terminal. 3/ Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD= (TJ(max) TA) / JA. Operating at the absolute maximum TJat +150C can affect reliability. 4/ The package the
13、rmal impedance is calculated in accordance with JESD 51-7. 5/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by I
14、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications f
15、or copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows:
16、A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operatin
17、g conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown
18、in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Truth table. The truth table shall be as shown in figure 3. 3.5.4 Logic diagram. The logic diagram shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuits. The timing wave
19、forms and test circuits shall be as shown in figures 5, 6, 7, and 8. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 5 TABLE I. Electrical performan
20、ce characteristics. 1/ Limits Test Symbol Conditions 2/Temperature, TADevice type Min Max Unit High level output voltage VOHIO= -20 mA -55C to +125C 01 2.2 V Low level output voltage VOLIO= 20 mA -55C to +125C 01 0.4 V Differential output voltage magnitude |VOD| RL= 100 , see figure 5 -55C to +125C
21、01 2 V Change in magnitude of differential output voltage |VOD| RL= 100 , see figure 5 3/ -55C to +125C 01 0.4 V Common mode output voltage VOCRL= 100 , see figure 5 -55C to +125C 01 3 V Change in magnitude of common mode output voltage |VOC| RL= 100 , see figure 5 3/ -55C to +125C 01 0.4 V Input cu
22、rrent IIVI= VCCor GND -55C to +125C 01 1 A Driver output current IO(off)VO= 6 V, VCC= 0 V -55C to +125C 01 100 A with power off VO= -0.25 V, VCC= 0 V -100 Driver output short circuit current IOSVO= 0 V -55C to +125C 01 -170 mA High impedance off state output current IOZVO= 2.5 V -55C to +125C 01 20
23、A VO= 0.5 V -20 Quiescent supply current ICCVI= 0 V or 5 V, IO= 0 -55C to +125C 01 100 A VI= 2.4 V or 0.5 V, IO= 0 4/ 3.2 mA Input capacitance CIVCC= 5 V +25C 01 6 typical pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
24、,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions 2/Temperature, TADevice type Min Max Unit Switching characteristics section. Unless otherwise specif
25、ied, CL= 50 pF. Propagation delay time, low to high level output tPLHS1 is open, see figure 6 -55C to +125C 01 12 ns Propagation delay time, high to low level output tPHLS1 is open, see figure 6 -55C to +125C 01 12 ns Pulse skew time ( |tPLH tPHL| ) tsk(p)S1 is open, see figure 6 -55C to +125C 01 4
26、ns Differential output rise and fall times tr(OD), tf(OD)S1 is open, see figure 7 -55C to +125C 01 12 ns Output enable time to high level tPZHS1 is closed, see figure 8 -55C to +125C 01 19 ns Output enable time to low level tPZLS1 is closed, see figure 8 -55C to +125C 01 19 ns Output disable time fr
27、om high level tPHZS1 is closed, see figure 8 -55C to +125C 01 16 ns Output disable time from low level tPLZS1 is closed, see figure 8 -55C to +125C 01 16 ns Power dissipation 5/ capacitance (each driver) CpdS1 is open, see figure 6, VCC= 5 V +25C 01 100 typical pF 1/ Testing and other quality contro
28、l techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product pe
29、rformance is assured by characterization and/or design. 2/ Unless otherwise specified, VCC= 4.5 V to 5.5 V. 3/ |VOD| and |VOC| are the changes in magnitude of VODand VOC, respectively, that occur when the input is changed from a high level to a low level. 4/ This parameter is measured per input. All
30、 other inputs are at 0 V or 5 V. 5/ Cpdis used to estimate the switching losses according to PD= Cpdx VCC2x f, where f is the switching frequency. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A C
31、ODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 7 Case X FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 8 Case X Dimensions
32、 Inches Millimeters Symbol Min Max Min Max A - 0.069 - 1.75 A1 0.004 0.010 0.10 0.25 b 0.012 0.020 0.31 0.51 c 0.007 0.010 0.17 0.25 D 0.386 0.394 9.80 10.00 E 0.150 0.157 3.80 4.00 E1 0.228 0.244 5.80 6.20 e 0.050 BSC 1.27 BSC L 0.016 0.050 0.40 1.27 NOTES: 1. All linear dimensions are in inches (m
33、illimeters). 2. Body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 inch (0.15 mm) per end. 3. Body width does not include interlead flash. Interlead flash shall not exceed .017 inch (0.43 mm) per side. 4. Falls within JED
34、EC MS-012 variation AC. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 9 Device type 01 Case outline X Termina
35、l number Terminal symbol 1 1A 2 1Y 3 1Z 4 G 5 2Z 6 2Y 7 2A 8 GND 9 3A 10 3Y 11 3Z 12 G 13 4Z 14 4Y 15 4A 16 VCCFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE
36、IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 10 ( Each driver ) Input Enables Output A G G Y Z H H X H L L H X L H H X L H L L X L L H X L H Z Z FIGURE 3. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLU
37、MBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 11 FIGURE 4. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 12 FIG
38、URE 5. Differential and common mode output voltages. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 13 NOTES: 1. C1, C2, C3 include probe and jig c
39、apacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, duty cycle 50 %, tr, tf 6 ns. FIGURE 6. Propagation delay time and skew waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
40、S-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 14 NOTES: 1. C1, C2, C3 include probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, duty cycle 50 %, tr, tf 6 ns. FIGURE
41、7. Differential output rise and fall time waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 15 NOTES: 1. C1, C2, C3 includ
42、e probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, duty cycle 50 %, tr 6 ns, and tf 6 ns. 3. Each enable is tested separately. FIGURE 8. Output enable and disable time waveforms and test circuit. Provided by IHSNot for ResaleN
43、o reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07647 REV PAGE 16 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requ
44、irements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling
45、, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein i
46、s based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herei
47、n is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Package 2/ Top side marking Vendor part number V62/07647-01XE 01295 Reel of 2500 26C31EP AM26C31MDREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineeri
