1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing YY MM DD CHECKED BY Phu H.
2、Nguyen APPROVED BY Thomas M. Hess TITLE MICROCIRCUIT, DIGITAL, ULTRALOW-POWER NTSC/PAL/SECAM VIDEO DECODER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/08626 08-08-04 REV PAGE 1 OF 9 AMSC N/A 5962-V060-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without li
3、cense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance ultralow-power NTSC/PAL/SECAM video decoder microcircuit, with an operating temperature
4、 range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/08626 - 01 X A Drawing Device type
5、Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TVP5150AM1-EP Ultralow-power NTSC/PAL/SECAM video decoder 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins Package style X
6、32 Plastic quad flatpack 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute maximum ratings. 1/ S
7、upply voltage range: IO_DVDD to DGND -0.5 V to 4.5 V DVDD to DGND -0.5 V to 2.3 V PLL_AVDD to PLL_AGND -0.5 V to 2.3 V CH_AVDD to CH_AGND -0.5 V to 2.3 V Digital input voltage range, VIto DGND . -0.5 V to 4.5 V Input voltage range, XTAL1 to PLL_GND -0.5 V to 2.3 V Analog input voltage range A1 to CH
8、_AGND . -0.2 V to 2.0 V Digital output voltage range, VO to DGND . -0.5 V to 4.5 V Storage temperature range, TSTG. -65C to 150C 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the d
9、evice at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
10、e from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 3 1.4 Recommended operating conditions. Digital I/O supply voltage, IO_DVDD 3.0 V to 3.6 V Digital supply voltage, DVDD . 1.65 V to 1.95 V Analog PLL supply voltage . 1.65 V to 1.95 V
11、 Analog core supply voltage, CH_AVDD . 1.65 V to 1.95 V Analog input voltage (ac-coupling necessary), VI(P-P) 0 V to 0.75 V Minimum digital input voltage high, VIH. 0.7 IO_DVDD V Maximum digital input voltage low, VIL. 0.3 IO_DVDD V Minimum XTAL input voltage high, VIH_XTAL 0.7 PLL_AVDD V Maximum XT
12、AL input voltage low, VIL_XTAL . 0.3 PLL_AVDD V Maximum high level output current, IOH 2 mA Maximum low level output current, IOL -2 mA Maximum SCLK high level output current, IOH_SCLK 4 mA Maximum SCLK low level output current, IOL_SCLK -4 mA Operating free air temperature . -55C to 125C 2. APPLICA
13、BLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industry Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently a
14、nd legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C
15、 (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions ar
16、e as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Functional block diagram. The functional block diagram shall be as shown in figure 3. 3.5.4 Tim
17、ing waveforms. The timing waveforms shall be as shown in figure 4-5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 4 TABLE I. Electrical performan
18、ce characteristics. 1/ Limits Test Symbol Conditions 2/ unless otherwise specified Min Max Unit DC electrical characteristics 3/ 3.3 V I/O digital supply current IDD(IO_D)Color bar input 4/ 10.0 mA 1.8 V digital supply current IDD(D)Color bar input 4 32.9 mA 1.8 V analog PLL supply current IDD(PLL_A
19、)Color bar input 4/ 7.1 mA 1.8 V analog core supply current IDD(CH_A)Color bar input 4 36.0 mA Total power dissipation, normal mode PTOTColor bar input 4/ 160 mW Total power dissipation, power down mode 5/ Color bar input 1 TYP mW Input capacitance CiBy design 8 TYP pF Output voltage high VOHIOH= 2
20、mA 0.8 IO_DVDD V Output voltage low VOLIOL= -2 mA 0.22 IO_DVDD V SCLK output voltage high VOH_SCLKIOH= 4 mA 0.8 IO_DVDD V SCLK output voltage low VOL_SCLKIOL= -4 mA 0.22 IO_DVDD V High level input current 6/ IIHVI= VIH28 A Low level input current 6ILVI= VIL28 Analog electrical characteristics Input
21、impedance, analog video inputs ZiBy design 500 TYP k Input capacitance, analog video inputs CiBy design 10 TYP pF Input voltage range 7/ Vi(pp)Ccoupling= 0.1 F 0 0.75 V Gain control maximum G 12 TYP dB Gain control minimum G 0 TYP dB DC differential nonlinearity DNL A/D only 1 LSB DC integral nonlin
22、earity INL A/D only 2.5 LSB Frequency response Fr 6 MHz, Specified by design -3 dB Signal to noise ratio SNR 6 MHz, 1.0 VP-P50 TYP Noise spectrum NS 50% flat field 50 TYP dB Differential phase DP 1.5 TYP Differential gain DG 0.5 TYP % See footnotes at end of table. Provided by IHSNot for ResaleNo re
23、production or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 5 TABLE I. Electrical performance characteristics Continued. Limits Test Symbol Conditions 2/ unless otherwise specified Min Max Unit
24、Clocks, Video data, Sync timing 8/ See figure 4 Duty cycle, PCLK 50 TYP % PCLK high time t1 80% 16 22 PCLK low time t2 20% 16 PCLK fall time t3 80% to 20% 4 TYP PCLK rise time t4 20% to 80% 4 TYP Output hold time t5 2 TYP Output delay time t6 3 TYP ns I2C host port timing 9/ See figure 5 Bus free ti
25、me between Stop and Start t1 1.3 s Setup time for a (repeated) Start condition t2 0.6 s Hold time (repeated) Start condition t3 0.6 s Setup time for a Stop condition t4 0.6 ns Data setup time t5 100 ns Data hold time t6 0 0.9 s Rise time, VC1(SDA) and VC0(SCL) signal t7 250 ns Fall time, VC1(SDA) an
26、d VC0(SCL) signal t8 250 TYP ns Capacitive load for each bus line Cb 400 pF I2C clock frequency fI2C400 kHz 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be teste
27、d across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ -55C TA 125C, DVDD = 1.8 V, PLL_AVDD = 1.8 V, CH_AVDD = 1.8 V, IO_DVDD = 3.3 V; for Typical value
28、TA= 25C unless otherwise noted. 3/ Measured with a load of 15 pF. 4/ For typical measurements only. 5/ Specified by device characterization. 6/ YOUT7 is a bidirectional terminal with an internal pull down resistor. This terminal may sink more than the specified current when in RESET mode. 7/ The 0.7
29、5 V maximum applies to the sync-chroma amplitude, not sync-white. The recommended termination resistor are 37.4 , as seen in the manufacturer data book. 8/ Measured with a load of 15 pF. Specified by design. 9/ Specified by design for industrial temperature. Provided by IHSNot for ResaleNo reproduct
30、ion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 6 Case X Dimension Millimeters Millimeters Symbol Min Max Symbol Min Max A 1.20 D/E 6.90 7.10 A1 0.95 1.05 D1/E1 4.95 5.05 A2 0.25 TYP D2/E2
31、3.50 TYP A3 0.05 0.15 e 0.50 BSC b 0.17 0.23 L1 0.40 0.70 C 0.13 NOM NOTES: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFE
32、NSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 7 Case X Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 AIP1A 9 PCLK/SCLK 17 YOUT1 25 HSYNC 2 AIP1B 10 IO_DVDD 18 YOUT0
33、 26 AVID 3 PLL_AGND 11 YOUT7/I2CSEL 19 DGND 27 AVIDINTREQ/GPCL/VBLK 4 PLL_AVDD 12 YOUT6 20 DVDD 28 PDN 5 XTAL1/OSC 13 YOUT5 21 SCL 29 REFP 6 XTAL2 14 YOUT4 22 SDA 30 REFM 7 AGND 15 YOUT3 23 FID/GLCO 31 CH_AGND 8 RESETB 16 YOUT2 24 VSYNC/PALI 32 CH_AVDD FIGURE 2. Terminal connections. FIGURE 3. Funct
34、ional block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 8 Clocks, Video data, and Sync Timing FIGURE 4. Timing waveforms. I2C Host port
35、 timing FIGURE 5. Timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08626 REV PAGE 9 4. VERIFICATION 4.1 Product assurance requirements. The manufa
36、cturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARAT
37、ION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class
38、1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of
39、supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62
40、/08626-01XE 01295 TVP5150AM1MPBSREP 5150MEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
