1、Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Richmond, ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616 or e-mailed to STDZNMGTDLA.MIL. Since contact information can change, you may want to verify the currency of this address
2、information using the ASSIST database at http:/assist.daps.dla.mil. AMSC N/A FSC 1560 INCH-POUND MIL-DTL-32331 29 June 2009 SUPERSEDING MS27380D 28 July 1982 DETAIL SPECIFICATION LANYARD, FLUID TANK CAP Inactive for new design after 12 June 2004 This specification is approved for use by all departme
3、nts and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the specifications for one type of lanyard, fluid tank cap. 1.2 Part or Identifying Number (PIN). PINs to be used for cap lanyards acquired to this specification are created as follows: MS27380 X Length: 1 6
4、 inch 3 12 inch Previous MS number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32331 2 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 or 4 of this specification. This section does not
5、 include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in secti
6、ons 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERI
7、CAN SOCIETY FOR QUALITY ANSI/ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (Copies of this document are available online at http:/www.asq.org or from American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI, 53203.) 3. REQUIREMENTS 3.1 Materials. 3.1.1 Materi
8、al. The lanyard shall be of molded polyurethane or other moldable elastomer or of woven or braided synthetic material as specified in the acquisition document (see 6.2). 3.1.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials s
9、hould be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 3.2 Design. 3.2.1 Molded. Molded lanyards shall conform to the dimensions shown in Figure 1. 3.2.2 Synthetic
10、 fiber. Fiber lanyards shall conform to the length and hole diameters of figure 1. The end radius shall not exceed that given in figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32331 3 3.3 Strength. The lanyard shall withstand a 40
11、pound (178 newton) pull. 4. VERIFICATION. 4.1 Sample size. The sample size will be determined in accordance with ANSI/ASQ Z1.4. The Inspection Level and Acceptance Quality Limit (AQL) shall be specified in the acquisition document (see 6.2) 4.2 Inspection. Each piece of the lot sample shall be inspe
12、cted for compliance to the material specification of 6.2 and the dimensional requirements of 3.2. 4.3 Strength. Each piece of the lot sample shall be tested for compliance to the strength requirement of 3.3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
13、MIL-DTL-32331 4 5. PACKAGING. 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house contract personnel, these personnel need to contact the responsible
14、 packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the inventory control points packaging activities within the military service or defense agency, or within the military services system commands. Packaging data retrieval is available from the managing
15、military services or defense agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES. (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 61 Acquisition requirements. Acquisition d
16、ocuments should specify the following: a. Title, number, and date of this specification. b. Required material (see 3.1.1) c. Inspection Level and AQL (see 4.1) d. Packaging requirements (see 5.1) 6.2 Metric conversions. The conversions below are given as a courtesy. It is still the manufacturers res
17、ponsibility to meet the dimensional requirements as given. The conversions are accurate within 0.01 mm. Inch Mm Inch Mm 0.015 0.38 0.250 6.35 0.025 0.64 0.875 22.23 0.125 3.18 6.000 152.40 0.135 3.43 12.000 304.80 0.188 4.78 6.3 Subject term (key word) listing. Polyurethane Synthetic fiber 6.4 Chang
18、es from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. The changes are to create a stand-alone document to replace the previous MS sheet due to the cancellation of the procurement specification
19、 of the MS sheet. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32331 5 Custodians: Preparing Activity: Army AV DLA-GS1 Navy AS Air Force 70 DLA - GS (Project 1560-2009-001) Review Activity: Air Force - 71 NOTE: The activities listed above
20、were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
