1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-83726/36D 6 March 2013 SUPERSEDING MIL-PRF-83726/36C 19 June 2012 PERFORMANCE SPECIFICATION SHEET RELAY, HYBRID, TIME DELAY (ON RELEASE), CLASS B, TYPE IIA, HERMETICALLY SEALED, 4PDT, 10 AMPERES, FIXED TIME DELAY, 0.1 TO 600 SECONDS This specification is approved
2、 for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83726. FIGURE 1. Outline dimensions and configuration of relay. Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-MIL-PRF-83726/36D 2 Inches mm Inches mm .001 0.03 .300 7.62 .002 0.05 .312 7.92 .005 0.13 .625 15.88 .040 1.02 .930 23.60 .050 1.27 1.025 26.04 .062 1.57 1.396 35.46 .150 3.81 1.446 33.73 .156 3.96 1.510 38.35 .200 5.08 1.718 43.64 .270 6.86 NOTES: 1. D
4、imensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm) for three place decimals and .03 (0.76 mm) for two place decimals. 4. Terminal numbers shall not appear on the relay header and there shall be a legible c
5、ircuit diagram on relay which identifies each terminal location specified. 5. Gasket material: The gasket material shall be of such quality to ensure the relay meets all the performance requirements of this specification. Silicone rubber gasket in accordance with SAE- AMS 3332, shore hardness 15 to
6、35 has been considered acceptable. 6. Terminal composition: The terminal composition shall be of such quality to ensure the relay meets all the performance requirements of this specification. Gold in accordance with SAE-AMS 2422 or ASTM B488, Type 3; underplating: nickel, 50 microinches to 150 micro
7、inches thick; has been considered acceptable. 7. Terminal Y2 is not used. FIGURE 1. Outline dimensions and configuration of relay Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 3 REQUIREMENTS: OPERATING REQUIREMENTS: Tim
8、ing action: Delay-on-release. Time delay: Fixed; select from 0.1 second to 600 seconds. Timing accuracy: 10 percent of nominal value. (The accuracy requirement applies for any combination of operating temperature and voltage. Add 10 ms for timing less than 1 second.) Recycle time: 50 milliseconds ma
9、ximum. (Recycle time is defined as the minimum time that power must be applied from the input terminals to assure that the next timing cycle will be completed within the specified timing tolerance. (Units can be recycled during timing or after time-out.) Power interrupt: 500 microseconds. (Transient
10、 and power loss specifications are based on a maximum duty cycle of 1/50.) Control voltage: 20 V dc to 30 V dc. Control current: 15 milliamperes maximum at 25C. Operating current: (X1-X2) 150 mA maximum at 25C. Extraneous voltage: 7 V dc minimum. INPUT REQUIREMENTS: Input voltage range: 20 V dc to 3
11、0 V dc. (EMI test limits will not be exceeded during the timing interval or when continuously energized under steady-state conditions in accordance with the EMI test of MIL-PRF-83726.) Duty rating: Continuous. Current drain: (quiescent)10 milliamperes maximum at 25C. Polarity protection: The timer s
12、hall be inoperative during, and undamaged by, reversal of the polarity of the operating voltage, or control voltage. OUTPUT REQUIREMENTS: Configuration: 4PDT. Life: See table I. TABLE I. Life load ratings (relay case grounded). Type of load Life (cycles) Amperes 28 V dc Amperes 115/200 V ac 400 Hz R
13、esistive Inductive Motor Lamp Low level 1/ 100,000 20,000 100,000 100,000 100,000 10 8 4 2 10 8 4 2 - 1/ Contact load 10 A to 50 A at 10 mV to 50 mV (dc or peak ac). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 4 ELECTRICAL REQUI
14、REMENTS: Transients: In accordance with MIL-STD-704 for 50 volts DC transients. Spike: Self-generated: 50 volts maximum. Spike transients: 600V, 10 microseconds maximum. Susceptibility: + 80 V maximum; -600 V maximum. Electromagnetic interference: In accordance with MIL-STD-461(methods CS101, CS114,
15、 RS101, and RS103) for PINs with suffix letter W. (EMI test limits will not be exceeded during the timing interval or when continuously energized under steady-state conditions in accordance with the EMI test of MIL-PRF-83726.) Insulation resistance: 1,000 megohms at 500 V dc at sea level, and 100 V
16、dc at 80,000 feet between each pin and case. (Terminals X1, X2, and Y1 must be connected together during this test. Insulation resistance is measured between all mutually insulated terminals and between all terminals and case.) Dielelectric withstanding voltage: 1,000 V rms at 60 Hz at sea level, an
17、d 350 V rms at 80,000 feet between case and pins connected together. (Terminals X1, X2, and Y1 must be connected together during this test. Dielectric withstanding voltage is measured between all mutually insulated terminals and between all terminals and case.) ENVIRONMENTAL REQUIREMENTS: Ambient te
18、mperature: Operating: -55C to +125C. Nonoperating): -65C to +125C. Vibration (sinusoidal): 30 gs, 10 Hz to 3,000 Hz. Vibration (random): 0.4 g2/Hz power spectral density, 50 Hz to 2,000 Hz in accordance with MIL-STD-202, method 214, test condition 1B. Shock (specified pulse): 100 gs, 6 ms 1 ms, .5 s
19、ine, 3 axes. Acceleration: 15 gs in any axis. Seal: Hermetic. Maximum altitude rating: 80,000 feet. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 5 PHYSICAL REQUIREMENTS: Dimensions and configuration: See figure 1. Mating socket:
20、MIL-DTL-12883/40-06, MIL-DTL-12883/40-12, MIL-DTL-12883/40-18, or MIL-DTL-12883/40-24. (CAUTION: Consideration should be given to ambient temperature and current requirements when using wire barrels size 20.) Terminations: See figure 1. Terminal strength: 3 pounds pull. Weight: 3.0 ounces maximum. M
21、arking: See MIL-PRF-83726. In addition, relays shall be marked with the ESDS identifier as specified in MIL-STD-1285. Part or Identifying Number (PIN): Consists of the prefix M83726/36-, a four digit dash number (time delay expressed in milliseconds), and a suffix letter (P for plug-in; S for solder
22、 lug): M 83726/36- 1001 P Military designation Specification sheet number The first three digits are significant; the fourth is the number of zeros to follow the first three digits. The time is expressed in milliseconds and converted to seconds. (See examples.) Suffix letter. (Any relay numbered pri
23、or to the date of this specification shall be considered interchangeable with same mounting type, store and issue.) Examples: M83726/36-1001P 1 second time delay, plug-in. M83726/36-9002S 90 second time delay, solder lug. NOTE: Time delay relays within the 0.1 second to 600 second delay range are av
24、ailable. The margins of this specification are marked with vertical lines to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to ev
25、aluate the requirements of this document based on the entire content irrespective of the marginal notations. Referenced documents. In addition to MIL-PRF-83726, this document references the following: SAE-AMS 3332 SAE-AMS 2422 ASTM B488 MIL-STD-704 MIL-STD-461 MIL-STD-1285 MIL-STD-202 Provided by IH
26、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 6 Custodians: Preparing activity: Army CR DLA - CC Navy - EC Air Force 85 (Project 5945-2013-011) DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
