1、 MS3116E 12 September 2013 SUPERSEDING MS3116D 19 August 1976 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, SOLDER TYPE, STRAIGHT, BAYONET COUPLING, SERIES 1, CLASSES E, F, J AND P This specification is approved for use by all Departments and Agencies of the Department of Defense. The req
2、uirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. STYLE P STYLE S PIN INSERT SOCKET INSERT FIGURE 1. Plug, classes E, F, J, and P. AMSC N/A FSC 5935 Inactive for new design after 15 December 1998, and is no longer used, except for repla
3、cement purposes. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 2 DETAIL A DETAIL B FIGURE 1. Plug, classes E, F, J and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
4、-,-MS3116E 3 Shell size A dia overall F .010 shoulder location G .020 bay lock location J + .020 / - .000 socket insert location N class 2A accessory thread UNEF 8 .782 (19.86) .353 (8.97) .113 (2.87) .337 (8.56) .438-28 10 .926 (23.52) .562-24 12 1.043 (26.49) .6875-24 14 1.183 (30.05) .8125-20 16
5、1.305 (33.15) .9375-20 18 1.391 (35.33) 1.0625-18 20 1.531 (38.89) .415 (10.54) .399 (10.13) 1.1875-18 22 1.656 (42.06) 1.3125-18 24 1.777 (45.14) .152 (3.86) 1.4375-18 FIGURE 1. Receptacle, classes E, F, J, and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted with
6、out license from IHS-,-,-MS3116E 4 Inches mm Inches mm .005 0.13 .020 0.51 .010 0.25 .031 0.79 .015 0.38 .036 0.91 .016 0.41 .141 3.58 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.
7、5. FIGURE 1. Plug, classes E, F, J and P - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 5 CLASS E, REAR ACCESSORY CONFIGURATION Shell size L max overall length X dia min ID Y dia max OD 8 1.328 (33.73) .259 (6.58) .608 (15.44) 1
8、0 .359 (9.12) .734 (18.64) 12 .469 (11.91) .858 (21.79) 14 .589 (14.96) .984 (24.99) 16 .717 (18.21) 1.110 (28.19) 18 .779 (19.79) 1.234 (31.34) 20 1.453 (36.91) .901 (22.89) 1.360 (34.54) 22 1.009 (25.63) 1.484 (37.69) 24 1.510 (38.35) 1.123 (28.52) 1.610 (40.89) NOTES: 1. Dimensions are in inches.
9、 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 2. Plug, rear accessories configurations, class E. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 6 C
10、LASS F, WITH BUSHING CLASS F, WITH BUSHING REMOVED FIGURE 3. Plug, rear accessories configurations, class F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 7 Shell size L max overall length Y max X dia min open V max closed N (see note 4) .0
11、10 free dia ZZ screw threads YZ (see note 5) lockwashers NASM35338 or NASM35333 types 8 1.906 (48.41) .828 (21.03) .234 (5.94) .187 (4.75) .125 (3.18) 6-32 UNC NASM35338 - 98 or -41 NASM35333 -105 or -37 10 .891 (22.63) .297 (7.54) .188 (4.78) 12 1.016 (25.81) .422 (10.72) .281 (7.14) .312 (7.92) 14
12、 1.141 (28.98) .547 (13.89) .325 (8.26) .375 (9.53) 16 2.047 (51.99) 1.203 (30.56) .609 (15.47) .356 (9.04) .500 (12.70) 18 2.078 (52.78) 1.469 (37.31) .734 (18.64) .456 (11.58) .625 (15.88) 8-32 UNC NASM35338 -B8L or -8L -99 or -42 NASM35333 -106 or -38 20 2.250 (57.15) .519 (13.18) 22 1.656 (42.06
13、) .922 (23.42) .750 (19.05) 24 2.312 (58.72) 1.750 (44.45) .984 (24.99) .657 (16.69) .800 (20.32) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Use SAE-AS85049/139 bushing
14、if reduced opening is required. 5. For class F: Lockwashers may be captivated. FIGURE 3. Plug, rear accessories configurations, class F - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 8 Shell size L max overall length V max close
15、d X ID gland seal min range Y dia max ZZ screw threads YZ (see note 4) Lockwashers NASM35338 or NASM35333 types closed open 8 2.271 (57.68) .187 (4.75) .169 (4.29) .230 (5.84) .828 (21.03) 6-32 UNC NASM35338 - 98 or -41 NASM35333 -105 or -37 10 .205 (5.21) .312 (7.92) .891 (22.63) 12 2.411 (61.24) .
16、281 (7.14) .338 (8.59) .442 (11.23) 1.016 (25.81) 14 2.599 (66.01) .325 (8.26) .416 (10.57) .539 (13.69) 1.161 (29.49) 16 2.943 (74.75) .356 (9.04) .550 (13.97) .616 (15.65) 1.203 (30.56) 18 3.172 (80.57) .456 (11.58) .600 (15.24) .672 (17.07) 1.469 (37.31) 8-32 UNC NASM35338 -B8L or -8L -99 or -42
17、NASM35333 -106 or -38 20 3.610 (91.69) .519 (13.18) .635 (16.13) .747 (18.97) 22 3.766 (95.66) .670 (17.02) .846 (21.49) 1.656 (42.06) 24 3.985 (101.22) .657 (16.69) .740 (18.79) .894 (22.71) 1.750 (44.45) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. T
18、rue position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Lockwashers may be captivated. FIGURE 4. Plug, rear accessories configurations, class J. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 9 Shell size L max overall l
19、ength X dia min ID Y dia max OD PP min 8 1.500 (38.10) .317 (8.05) .608 (15.44) .250 (6.35) 10 .434 (11.02) .734 (18.64) 12 .548 (13.92) .858 (21.79) 14 .673 (17.09) .984 (24.99) 16 .798 (20.27) 1.110 (28.19) 18 .899 (22.83) 1.234 (31.34) 20 1.609 (40.87) 1.024 (26.01) 1.360 (34.54) 22 1.149 (29.18)
20、 1.484 (37.69) 24 1.687 (42.85) 1.274 (32.36) 1.610 (40.89) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 5. Plug, rear accessories configurations, class P. Provided by IH
21、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS3116E 10 REQUIREMENTS: Dimensions and configurations: See figures 1 through 5. Connector mating: This connector mates with MS3110, MS3112, MS3113, MS3114 and MS3119. For insert arrangement: See MIL-STD-1669. Interm
22、ateability dimensions are in accordance with MIL-DTL-26482. Finishes: A finish designator shall not be included in the PIN when finish W is required. See MIL-DTL-26482 for other finishes, including D, T and K, available for classes E, F, P and J. Part or Identifying Number (PIN) example: MS3116 F 12
23、 -3 P W D MS number Class Shell size Insert arrangement Contact style Alternate insert position Finish Note: When finish W is required, no finish designator is used (class W is the default finish). Restrictions: Changes from previous issue. Marginal notations are not used in this revision to identif
24、y changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: MIL-STD-1669 ASME-Y14.5 SAE-AS85049/139 Not for Air Force use. For Air Force use, use MS3476. Provided by IHSNot for ResaleNo rep
25、roduction or networking permitted without license from IHS-,-,-MS3116E 11 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2012-225) Army - AV Navy - EC, SH Air Force - 99 NOTE: The activities listed above were
26、interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
