1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to the latest requirements. -sld 07-05-02 Robert M. Heber B Table II, add note to Group C end-point test parameters. -gz 09-11-24 Charles F. Saffle C Corrected dimensions for symbols D, D2, and L1 for case outline U. Corrected dime
2、nsions for symbols D2, L, and L1 for case outline X. Corrected dimensions for symbols D, L, and L1 for case outline Y. Corrected dimensions for symbols D, D2, and L1 for case outline Z. Updated drawing paragraphs. -sld 13-01-23 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C
3、 C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin M
4、ICROCIRCUIT, HYBRID, LINEAR, 9 VOLT, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 02-11-06 SINGLE CHANNEL, DC/DC CONVERTER AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-02550 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E150-13Provided by IHSNot for ResaleNo reproduction or ne
5、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and M
6、IL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 02550
7、 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 spe
8、cified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AFL12009S/CH DC/DC converter, 90 W, +9 V output 1.2.3 De
9、vice class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product ass
10、urance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices ar
11、e required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance
12、inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewe
13、d to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outlines. The case outlines are as d
14、esignated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U See figure 1 12 Y case configuration with leads bent upwards X See figure 1 12 Straight leads with end mounting through holes Y See figure 1 12 Straight leads with side mounting through holes Z
15、See figure 1 12 Y case configuration with leads bent downwards 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MAR
16、ITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +180 V dc Lead temperature (soldering, 10 seconds) +300C Storage temperature -65C to +135C 1.4 Recommended operating conditions. Input voltage range +80 V
17、dc to +160 V dc Output power 2/ . 90 W Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherw
18、ise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interfa
19、ce Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Docu
20、ment Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable la
21、ws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tes
22、ts herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for
23、 the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may
24、degrade performance and affect reliability. 2/ Derate output power linearly above case temperature +125C to 0 at +135C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MARITIME COLUMBUS, OH
25、IO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and fig
26、ure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating tempe
27、rature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be mark
28、ed with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from
29、the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufa
30、cturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land an
31、d Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICA
32、TION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Scre
33、ening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to
34、 either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of me
35、thod 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted with
36、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C VIN= 120 V dc 5%, CL= 0 unless otherwise sp
37、ecified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 10 A 1 01 +8.91 +9.09 V 2,3 +8.82 +9.18 Output current 2/ IOUTVIN = 80, 120, and 160 V dc 1,2,3 01 10 A Output ripple voltage VRIPVIN = 80, 120, and 160 V dc, B.W. = 10 MHz 1,2,3 01 40 mV p-p Line regulation VRLINEVIN
38、 = 80, 120, and 160 V dc, IOUT= 0, 5, and 10 A 1,2,3 01 20 mV Load regulation VRLOADVIN = 80, 120, and 160 V dc, IOUT= 0, 5, and 10 A 1,2,3 01 90 mV Input current IINIOUT = no load 1 01 30 mA 2,3 40 Enable 1, (pin 4) shorted to Input return (pin 2) 1,2,3 3 Enable 2, (pin 12) shorted to Output return
39、 (pin 8) 1,2,3 5 Input ripple current IRIPIOUT = 10 A, B.W. = 10 MHz 1,2,3 01 60 mA p-p Efficiency EFFIOUT = 10 A 1,2,3 01 80 % Isolation ISO Input to output or any pin to case (except pin 3) at 500 V dc, TC = +25C 1 01 100 M Maximum capacitive load 3/ CLNo effect on dc performance, TC= +25C 4 01 10
40、,000 F Power dissipation load fault PDOverload 1,2,3 01 32 W Short circuit 32 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-39
41、90 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C VIN= 120 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Current limit point 4/ ICLVOUT = 90% VNOM 1 01 1
42、1.50 12.50 A 2 10.50 11.50 3 12.50 14.00 Switching frequency FSIOUT= 10 A 1,2,3 01 500 600 kHz Sync frequency range FSYNCIOUT = 10 A 1,2,3 01 500 700 kHz Output response to step transient load changes 5/ 6/ VOTLOAD50% to/from 100% 4,5,6 01 -500 +500 mV pk 10% to/from 50% -500 +500 Recovery time, ste
43、p transient load changes 5/ 6/ TTLOAD50% to/from 100% 4,5,6 01 200 s 10% to/from 50% 400 Output response to transient step line changes 3/ 5/ 7/ VOTLINEInput step, 80 V to/from 160 V dc, IOUT = 10 A 4,5,6 01 -500 +500 mV pk Recovery time transient step line changes 3/ 5/ 7/ TTLINEInput step, 80 V to
44、/from 160 V dc, IOUT= 10 A 4,5,6 01 500 s Turn on overshoot 8/ VTonOSIOUT= 0 and 10 A 4,5,6 01 250 mV pk Turn on delay 8/ TonDIOUT= 0 and 10 A 4,5,6 01 120 ms Load fault recovery 8/ TrLF4,5,6 01 120 ms 1/ All electrical tests are performed with the remote sense leads connected to the output leads at
45、 the load. Pin 10 to pin 7 and pin 9 to pin 8. 2/ Parameter verified as part of another test. 3/ Parameter not 100% tested but are guaranteed to the limits specified in the table. 4/ Current limit point is that condition of excess load causing output voltage to drop to 90% of nominal. 5/ Recovery ti
46、me is measured from the initiation of the transient to where VOUThas returned to within 1% of VOUTat 50% load. 6/ Load transient transition time 10 s. 7/ Line transient transition time 100 s. 8/ Turn-on delay is measured with an input voltage rise time of between 100 and 500 volts per millisecond. P
47、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-02550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline U. Millimeters Inches Symbol Min Max Min Max A
48、9.65 .380 D 70.35 71.96 2.770 2.833 D1 63.37 63.63 2.495 2.505 D2 13.08 13.59 .515 .535 E 37.97 38.23 1.495 1.505 e1 50.6 51.1 1.99 2.01 e2 25.27 25.53 .995 1.005 F 1.14 1.40 .045 .055 L 10.4 10.9 .41 .43 L1 5.33 5.84 .210 .230 q 44.32 44.58 1.745 1.755 q1 29.08 29.34 1.145 1.155 q2 44.32 44.58 1.745 1.755 q3 6.1 6.6 .24 .26 q4 7.49 7.75 .295 .305 q5 9.40 9.65 .370 .380 S 6.22 6.48 .245 .255 b 0.89 1.14 .035 .045 p 3.43 3.68 .135 .145 NOTES: 1. The U.S. government preferred syste
