1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV SHET REV SHET REV STATUS REV OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Steve Duncan STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ APPROVED
2、 BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, SAMPLING A/D CONVERTER, 16-BIT RESOLUTION THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 06-08-30 AMSC N/A REVISION LEVEL SIZE A CAGE CODE 67268 5962-06257 SHEET 1 OF 11 DSCC FORM 2
3、233 APR 97 5962-E632-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This dra
4、wing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in t
5、he PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 06257 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardnes
6、s assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic nu
7、mber Circuit function 01 MN6500S/B CH Sampling A/D converter, 16-bit resolution 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as w
8、ell as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. Th
9、is level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified inc
10、oming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified i
11、n the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This produc
12、t may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case o
13、utline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply vo
14、ltage range (+VCC). 0 V dc to +16.5 V dc Negative supply voltage range (-VCC) 0 V dc to -16.5 V dc Logic supply voltage range (+VA) -0.3 V dc to +6 V dc Analog input channels . 16.5 V dc Digital input range . -0.3 V dc to (+VA)+0.3 V dc Power dissipation (PD). 1120 mW Thermal resistance, junction to
15、 case (JC). 5C/W Thermal resistance, junction to ambient (JA) 38C/W Lead temperature (soldering, 10 seconds) +300C Storage temperature range . -65C to +150C Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Positive supply voltage range (+VCC). +11.4 V dc to +16.5 V dc Negative s
16、upply voltage range (-VCC) -11.4 V dc to -16.5 V dc Logic supply voltage range (+VA) +4.5 V dc to +5.5 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks for
17、m a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MI
18、L-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online
19、at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the max
20、imum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 4 DSCC FORM 2234
21、 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQ
22、UIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Managemen
23、t (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM pl
24、an shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in
25、 accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply ov
26、er the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of Device(s). Marking of device(s) shall be in accordance wit
27、h MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the elec
28、trical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under docu
29、ment revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) s
30、ubmitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VER
31、IFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IH
32、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbo
33、l Conditions 1/ -55C TA +125C unless otherwise specified Group A Subgroups Device type Min Max Unit 0 +5 Unipolar 1,2,3 01 0 +10 V -5 +5 Input voltage range VIBipolar 1,2,3 01 -10 +10 V Input voltage high VIHFor all digital inputs 1 01 +2.0 V Input voltage low VIL For all digital inputs 1 01 +0.8 V
34、Input current high IIHVIH= +2.4 V 1 01 -10 +10 A Input current low IILVIL= +0.4 V 1 01 -10 +10 A Output voltage high VOHIOH= -40 A 1 01 +2.4 V Output voltage low VOLIOL= +1.6 mA 1 01 +0.4 V Positive supply current ICC+VCC= +15 V 1 01 13 mA Negative supply current IEE-VCC= -15 V 1 01 -50 mA Logic sup
35、ply current IDD+VA= +5 V 1 01 35 mA Power dissipation PDWorse case (all 1s or all 0s) 1 01 1120 mW +14.5 V +VCC +15.5 V -0.01 +0.01 -15.5 V -VCC -14.5 V -0.01 +0.01 Power supply rejection ratio PSSR +4.5 V +VA +5.5 V 1 01 -0.01 +0.01 %FSR/%Vs See footnotes at end of table. Provided by IHSNot for Res
36、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbo
37、l Conditions 1/ -55C TA +125C unless otherwise specified Group A Subgroups Device type Min Max Unit Unipolar 10 V 2/ V+FSMSB LSB nominal 1111 1111 1111 111* +9.99977 4 01 +9.98977 +10.00977 V +4.98977 +5.00977 Bipolar 10 V 2/ V+FSV-FSMSB LSB nominal 1111 1111 1111 111* +4.99977 MSB LSB nominal 0000
38、0000 0000 000* -4.99992 4 01 -5.00992 -4.98992 V +9.97954 +10.01954 Bipolar 20 V 2/ V+FSV-FSMSB LSB nominal 1111 1111 1111 111* +9.99954 MSB LSB nominal 0000 0000 0000 000* -9.99985 4 01 -10.01985 -9.97985 V Unipolar offset 10 V 2/ VUOMSB LSB nominal 0000 0000 0000 000* +0.076 4 01 -2.924 +3.076 mV
39、Bipolar 10 V zero 2/ VBZ1MSB LSB nominal * * * * -0.076 4 01 -3.076 +2.924 mV Bipolar 20 V zero 2/ VBZ2MSB LSB nominal * * * * -0.153 4 01 -6.153 +5.847 mV Unipolar 10 V 2/ V+FSMSB LSB nominal 1111 1111 1111 111* +9.99977 5,6 01 +9.97477 +10.02477 V +4.97477 +5.02477 Bipolar 10 V 2/ V+FSV-FSMSB LSB
40、nominal 1111 1111 1111 111* +4.99977 MSB LSB nominal 0000 0000 0000 000* -4.99992 5,6 01 -5.02492 -4.97492 V +9.94954 +10.04954 Bipolar 20 V 2/ V+FSV-FSMSB LSB nominal 1111 1111 1111 111* +9.99954 MSB LSB nominal 0000 0000 0000 000* -9.99985 5,6 01 -10.04985 -9.94985 V Unipolar offset 10 V 2/ VUOMSB
41、 LSB nominal 0000 0000 0000 000* +0.076 5,6 01 -6.924 +7.076 mV Bipolar 10 V zero 2/ VBZ1MSB LSB nominal * * * * -0.076 5,6 01 -7.076 +6.924 mV Bipolar 20 V zero 2/ VBZ2MSB LSB nominal * * * * -0.153 5,6 01 -14.153 +13.847 mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproductio
42、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -
43、55C TA +125C unless otherwise specified Group A Subgroups Device type Min Max Unit Integral linearity error LE Offset endpoint method 1.5 LSB at 16 bits 3/ 4,5,6 01 -0.0022 +0.0022 %FSR No missing codes at 15 bits 3/ 4 -1.9 +4.0 Differential linearity Error DLE No missing codes at 14 bits 3/ 5,6 01
44、-3.9 +8.0 LSB Resolution RES 4,5,6 01 16 bits Reference voltage VREF4/ 4 01 +4.45 +4.55 V Conversion time tCFCLK= 8 MHz 5/ 9,10,11 01 8.12 s Bipolar 10 V range, FSAMPLE= 100 kHz, fIN= 1 kHz 4 01 -92 Harmonics and Spurious noise SFDR Bipolar 10 V range, FSAMPLE= 100 kHz, fIN= 24 kHz 4 01 -84 dB Bipol
45、ar 10 V range, FSAMPLE= 100 kHz, fIN= 1 kHz, 0 dB 4 01 84 Signal to Noise and Distortion SINAD Bipolar 10 V range, FSAMPLE= 100 kHz, fIN= 24 kHz, 0 dB 4 01 76 dB 1/ Unless otherwise specified, +VCC= +15 V, -VCC= -15 V, +VA= +5 V. 2/ * Indicates the output will transition from a “1“ to “0“ or vice ve
46、rsa as the analog input passes through the voltages listed in the limit columns. 3/ Specification listed applies after calibration at the specified temperature. 4/ Reference output is to be bypassed to analog ground with a 10 f capacitor in parallel with a 0.1 f capacitor. Reference must not be used
47、 for applications circuits without buffering. 5/ Parameter not tested. Conversion time of 8.12 s is set by a 8 MHz external clock Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06257 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A 4.65 .183 b 0.381 0
