1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline Y. -gc 13-07-02 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Greg Cecil DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Gre
2、g Cecil COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Charles F Saffle MICROCIRCUIT, HYBRID, 5 VOLT, DUAL CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 11-06-16 AMSC N/A REVISION LEVEL SIZE
3、 A CAGE CODE 67268 5962-10224 A SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E475-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2
4、DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radi
5、ation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 10224 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (s
6、ee 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the c
7、ircuit function as follows: Device type Generic number Circuit function 01 LS2805D DC/DC Converter, 30 W, 5 V Output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-385
8、34 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Stan
9、dard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperat
10、ure range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. T
11、hese exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers inte
12、rnal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC
13、 FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See Figure 1 8 Flanged Package Y See figure 1 8 Straight leads with side mounting through holes 1.2.5 Lead finish. The lead f
14、inish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +60 V dc (continuous) Lead temperature (soldering, 10 seconds) +300C Storage temperature range -55C to +135C 1.4 Recommended operating conditions. Input voltage range +18 V dc to +40 V dc
15、Output Power . 30 W Case operating temperature range (TC) . -55C to +85C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the i
16、ssues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electron
17、ic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins
18、Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a s
19、pecific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
20、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance
21、with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections
22、 herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimen
23、sions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 El
24、ectrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgrou
25、ps specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also
26、be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein
27、. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3
28、.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MI
29、L-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MI
30、L-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
31、T DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+85C VIN = 28 V DC 5%, CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit
32、 Min Max Input Voltage 1/ VIN01 18 40 V Output Voltage VOUTVIN= 28 V, 100% load on both outputs 1 01 4.95 5.05 V 2, 3 4.90 5.10 Output Current 2/ 3/ IOUTVIN= 18, 28, 40 V dc Either output 1, 2, 3 01 4.8 A Output Power 2/ 3/ POUT VIN= 18, 28, 40 V dc 1, 2, 3 01 30 W Output Ripple Voltage 2/ 4/ VRiPVI
33、N= 18, 28, 40 V dc IOUT= 4.8 A, BW = 20 Hz to 2 MHz 1, 2, 3 01 80 mV p-p Line Regulation 4/ VRLINEVIN= 18, 28, 40 V dc IOUT= 0, 2.4, and 4.8 A 1, 2, 3 01 -0.5 +0.5 % Load Regulation 4/ VRLOADVIN= 18, 28, 40 V dc IOUT= 0, 2.4, and 4.8 A 1, 2, 3 01 -1.0 +1.0 % Cross Regulation 5/ VRCROSS VIN= 16, 28,
34、40 V dc 1, 2, 3 01 -5.0 +5.0 % Input Current IINIOUT = 0, Pin 4 open 1, 2, 3 01 70 mA Pin 4 shorted to pin 2 1, 2, 3 01 8 mA Efficiency 4/ EFFIOUT= 4.8 A 1, 2, 3 01 79 % Isolation ISO Input to output or any pin to case except pin 3 at 500 V dc 1 01 100 M Maximum Capacitive Load 6/ 1/ CLIOUT= 4.8 A,
35、each output 1 01 500 F Power Dissipation Load Fault PDShort circuit, Overload 1, 2, 3 01 14 W Current Limit Point ILIMVOUT = 90% of nominal 4, 5, 6 01 105 145 % Switching Frequency FS100% load 4, 5, 6 01 425 575 kHz See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or netwo
36、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+85C VIN = 28V DC 5%,
37、 CL = 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Line Rejection 2/ 4/ 1/ REJ 100% load, DC to 50 kHz , 1 01 35 dB Enable Input (Inhibit) 1/ Open circuit voltage ENB 01 9 12 V Drive current (sink) 1/ 0 5.0 mA Voltage range 1/ -0.5 50 V Output response to step load
38、changes 4/ 7/ VTLD50% to/from 100% load 4, 5, 6 01 -300 300 mV pk Recovery time, step load changes 4/ 7/ 8/ TTLD50% to/from 100% load 4, 5, 6 01 200 S Output response to step line changes 4/ 6/ 9/ VTLNInput step 18 V to/from 40 V IOUT= 4.8 A 4, 5, 6 01 -300 300 mV pk Recovery time, step line changes
39、 4/ 1/ 9/ TTLNInput step 18 V to/from 40 V IOUT= 4.8 A 4, 5, 6 01 200 S Turn-On overshoot 4/ 10/ VOS10% load, 100% load 4, 5, 6 01 500 mV Turn-On Delay 4/ 10/ TDLY10% load, 100% load 4, 5, 6 01 10 mS 1/ Parameter is tested as part of design characterization or after design changes. Thereafter, param
40、eter shall be guaranteed to the limits specified. 2/ Applicable to positive and negative outputs. 3/ Output load current must be distributed such that at least 20 percent of the total load current is being provided by one of the outputs. 4/ Load current split equally between +VOUTand VOUT. 5/ Cross
41、regulation is measured with 20 percent rated load on output under test while changing the load on the other output from 20 percent to 80 percent of rated. 6/ Capacitance load may be any value from 0 to the maximum limit without compromising DC performance. 7/ Load step transition time 10 microsecond
42、s. 8/ Recovery time is measured from the initiation of the transient to where VOUThas returned to within 1 percent of its steady state value at 50 percent load. 9/ Input line step transition time 100 microseconds. 10/ Turn-on delay time from either a step application of input power or a logic low to
43、 logic high transition on the enable pin. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Case outline X.
44、 Symbol Millimeters Inches Min Max Min Max A 10.80 .425 D 70.87 71.37 2.79 2.81 D1 58.29 58.55 2.295 2.305 E 50.67 50.93 1.995 2.005 e1 44.32 44.58 1.745 1.755 e2 37.97 38.23 1.495 1.505 e3 25.27 25.53 .995 1.005 e4 10.03 10.29 .395 .405 e5 10.03 10.29 .395 .405 F 1.14 1.40 .045 .055 L 6.22 6.48 .24
45、5 .255 L1 5.46 5.72 .215 .225 q1 39.24 39.50 1.545 1.555 q2 8.76 9.02 .345 .355 q3 21.46 21.72 .845 .855 s 6.73 6.99 .265 .275 s1 11.81 12.07 .465 .475 s2 10.03 10.29 .395 .405 s3 4.95 5.21 .195 .205 b 0.89 1.14 .035 .045 p 3.38 3.63 .133 .143 Notes: 1. The US government preferred system of measurem
46、ent is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Case outline weight: 80 grams maximum. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo repr
47、oduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-10224 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters Inches Min Max Min Max A 10.80 0.425 D 70.87 71.37 2.79 2.81
48、 D1 58.29 58.55 2.295 2.305 E 37.97 38.23 1.495 1.505 e3 25.27 25.53 0.995 1.005 e4 10.03 10.29 0.395 0.405 e5 10.03 10.29 0.395 0.405 L 6.22 6.48 0.245 0.255 L1 5.46 5.72 0.215 0.225 s 6.73 6.99 0.265 0.275 s1 11.81 12.07 0.465 0.475 s2 10.03 10.29 0.395 0.405 s3 4.95 5.21 0.195 0.205 b 0.89 1.14 0.035 0.045 NOTES: 1. The US government preferred system of measurement is the metric SI. This item was designed using inch-po
