1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 02-05-10 R. MONNIN B Five year review requirement. - ro 08-06-10 R. HEBER REV SHET REV SHET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RA
2、JESH PITHADIA DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY RAYMOND MONNIN AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 98-04
3、-07 MICROCIRCUIT, LINEAR, RAIL-TO-RAIL, WIDE INPUT VOLTAGE, MICROPOWER, DUAL OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-97514 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E172-08 Provided by IHSNot for ResaleNo reproduction or networking permitted wit
4、hout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class
5、es Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the
6、following example: 5962 - 97514 01 Q H A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MI
7、L-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device t
8、ype(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TLV2422M Rail-to-rail, wide-input-voltage, micropower dual operational amplifiers 02 TLV2422AM Rail-to-rail, wide-input-voltage, micropower dual operational amplifiers (enhanced VIO) 1.2.3 Device class de
9、signator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
10、 appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2
11、 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
12、IRCUIT DRAWING SIZE A 5962-97514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VDD) . +12.0 V dc 2/ Differential input voltage (VID) . VDD3/ Input current, each input (IIN) 5.0 mA Output curren
13、t (IOUT) 50.0 mA Total current into +VDD. 50.0 mA Total current out of -VDD50.0 mA Duration of short-circuit current at (or below) +25C . Unlimited 4/ Continuous total power dissipation (PD) 5/ Case H 675 mW Case P . 1050 mW Case 2 . 1375 mW Operating free-air temperature range (TA) -55C to +125C St
14、orage temperature range (TSTG) . -65C to +150C Lead temperature 1.6 mm (1/16 seconds) from case for 10 seconds . +260C Maximum junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case outlines H and P . 180C/W C
15、ase outline 2 65C/W 1.4 Recommended operating conditions. Supply voltage range (VDD) 2.7 V dc to 10.0 V dc Input voltage range (VIN) -VDDto +VDD- 0.8 V Common-mode input voltage (VIC) . -VDDto +VDD- 0.8 V Ambient operating temperature range (TA) . -55C to +125C _ 1/ Stresses above the absolute maxim
16、um rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltage values, except differential voltages, are with respect to the midpoint between +VDDand -VDD. 3/ Differential voltages are at the noninverting in
17、put with respect to the inverting input. Excessive current flows if the input is brought below -VDD- 0.3 V. 4/ The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. 5/ Above TA= +25C, derate by th
18、e following factors: case H at 5.4 mW/C, case P at 8.4 mW/C, and case 2 at 11.0 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LE
19、VEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those ci
20、ted in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlin
21、es. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Bui
22、lding 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exe
23、mption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shal
24、l not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, constructio
25、n, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections sh
26、all be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient opera
27、ting temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufactur
28、ers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device clas
29、ses Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark fo
30、r device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET
31、5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxInput offset voltage VIOVIC= 0 V, VDD= 1.5 V, 1 01 2000 V VO= 0 V, RS= 50 2,3 2500 1 02 950 2,3 1800 VIC= 0 V,
32、VDD= 2.5 V, 1 01 2000 VO= 0 V, RS= 50 2,3 2500 1 02 950 2,3 1800 Input offset current IIOVIC= 0 V, VDD= 1.5 V, VO= 0 V, RS= 50 2,3 All 150 pA VIC= 0 V, VDD= 2.5 V, VO= 0 V, RS= 50 150 Input bias current IIBVIC= 0 V, VDD= 1.5 V, VO= 0 V, RS= 50 2,3 All 300 pA VIC= 0 V, VDD= 2.5 V, VO= 0 V, RS= 50 300
33、 Common-mode input voltage range VICR|VIO| 5 mV, RS= 50 , 1 All 0 to 2.5 V VDD= 3.0 V 2,3 0 to 2.2 |VIO| 5 mV, RS= 50 , 1 0 to 4.5 VDD= 5.0 V 2,3 0 to 4.2 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI
34、RCUIT DRAWING SIZE A 5962-97514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ U
35、nit Min MaxHigh level output voltage VOHIOH= -500 A, VDD= 3.0 V 1,2,3 All 2.5 V IOH= -1 mA, VDD= 5.0 V 4.5 Low level output voltage VOLVIC= 0 V, IOL= 250 A, VDD= 3.0 V 1,2,3 All 0.5 V VIC= 2.5 V, IOL= -1 mA, VDD= 5.0 V 0.5 Large signal differential voltage amplification AVDVIC= 1.5 V, 2/ VDD= 3.0 V,
36、 RL= 10 k, 4 All 6 V/mV VO= 1 V to 2 V 5,6 2 VIC= 2.5 V, 3/ VDD= 5.0 V, RL= 10 k, 4 8 VO= 1 V to 4 V 5,6 3 Common mode rejection ratio CMRR VIC= 0 V to VICRmin, VDD= 3.0 V, VO= 1.5 V, RS= 50 1,2,3 All 70 dB VIC= 0 V to 4.5 V, VDD= 5.0 V, VO= 2.5 V, RS= 50 70 Supply voltage rejection ratio (VDD/ VIO)
37、 kSVRVDD= 2.7 V to 8 V, VDD= 3.0 V, VIC= VDD/ 2, no load 1,2,3 All 80 dB VDD= 4.4 V to 8 V, VDD= 5.0 V, VIC= VDD/ 2, no load 80 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9
38、7514 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Max Supply current
39、IDDVO= 1.5 V, no load, 1 All 150 A VDD= 3.0 V 2,3 175 VO= 2.5 V, no load, 1 150 VDD= 5.0 V 2,3 175 Slew rate at unity gain SR VDD= 3.0 V, 4/ RL= 10 k, CL= 100 pF, 4 All 0.01 V/s VO= 1.1 V to 1.9 V 5,6 0.008 VDD= 5.0 V, 5/ RL= 10 k, CL= 100 pF, 4 0.01 VO= 1.5 V to 3.5 V 5,6 0.008 1/ All characteristi
40、cs are measured with zero common mode input voltages unless otherwise specified. 2/ Load resistance is referenced to 1.5 V. 3/ Load resistance is referenced to 2.5 V. 4/ Load resistance and load capacitance are referenced to 1.5 V. 5/ Load resistance and load capacitance are referenced to 2.5 V. 3.6
41、 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer
42、in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requiremen
43、ts of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided wi
44、th each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification a
45、nd review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group
46、assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 73 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97514 DE
47、FENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outlines H P 2 Terminal number Terminal symbol 1 NC OUTPUT 1 NC 2 OUTPUT 1 -INPUT 1 OUTPUT 1 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 -VDD/ GND NC 5 -VDD/ GND +INPUT 2 -INPUT 1
48、6 +INPUT 2 -INPUT 2 NC 7 -INPUT 2 OUTPUT 2 +INPUT 1 8 OUTPUT 2 +VDDNC 9 +VDD- NC 10 NC - -VDD/ GND 11 - - NC 12 - - +INPUT 2 13 - - NC 14 - - NC 15 - - -INPUT 2 16 - - NC 17 - - OUTPUT 2 18 - - NC 19 - - NC 20 - - +VDDNC = No connection Pin description Terminal symbol Description +INPUT m (m = 1 to 2) Non-inverting inputs -INPUT m (m = 1 to 2) Inverting inputs OUTPUT m (m = 1 to 2) Outputs FIGURE 1. T
