1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 4632-004:2012Aerospace series Weldability and brazeability of materials in aerospace constructionsPart 004: Welding and brazing of homogeneous assemblies of high alloyed st
2、eelsBS EN 4632-004:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4632-004:2012. The UK participation in its preparation was entrusted to TechnicalCommittee ACE/61, Metallic materials for aerospace purposes. A list of organizations represented on this comm
3、ittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 65866 2 ICS 49.
4、025.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 4632-004:2012EUROPEAN
5、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4632-004 September 2012 ICS 49.025.01 English Version Aerospace series - Weldability and brazeability of materials in aerospace constructions - Part 004: Welding and brazing of homogeneous assemblies of high alloyed steels Srie arospatiale - Soudabilit et
6、 brasabilit des matriaux pour constructions arospatiales - Partie 004: Assemblagessouds et brass homognes daciers fortement allis Luft- und Raumfahrt - Schweieignung und Lteignung von Werkstoffen im Luft- und Raumfahrzeugbau - Teil 004: Schweien und Lten gleichartiger Verbingungen aus hochlegeirten
7、Sthler This European Standard was approved by CEN on 23 March 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographica
8、l references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility o
9、f a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Ma
10、cedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION E
11、UROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4632-004:2012: EBS EN 4632-004:2012EN 4632-004:2012 (E) 2 Contents Page Foreword . 31Scope . 42
12、Normative references . 43Terms and definitions . . 94Abbreviations . . 95Use of this standard . 106Updating . .107List of highly alloyed steels . 108Highly alloyed steels . .11Bibliography . 35BS EN 4632-004:2012EN 4632-004:2012 (E) 3 Foreword This document (EN 4632-004:2012) has been prepared by th
13、e Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD
14、, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2013, and conflicting national standards shall be withdrawn at the latest by March 2013. Attention is draw
15、n to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the followin
16、g countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw
17、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4632-004:2012EN 4632-004:2012 (E) 4 1 Scope This European Standard specifies the weldability and brazeability of materials or material families used in the aerospace industry. It compr
18、ises a series of sheets, by materials or material family, which: indicate the main titles, the typical chemical composition and the main characteristics, contain recommendations for welding and brazing, indicate a degree of weldability or brazeability for a given process under defined conditions, in
19、dicate a value for the welded joint mechanical resistance coefficient for each welding process when extracted from relevant bibliographical references. Joint coefficient is the ratio of stress resistance transversally to welded joint over tensile strength of parent alloy. It recommends ISO/TR 17671-
20、3 and EN 1011-3 for pre-heating conditions specially for the welding of martensitic steels. These conditions depend on the line energy of welding, thickness, arc welding process and of hydrogen rate in filler metal. It applies unreservedly to the manufacturing of new parts or for repair. 2 Normative
21、 references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appl
22、ies. EN 1011-3, Welding Recommendations for welding of metallic materials Part 3: Arc welding of stainless steels EN 1045, Brazing Fluxes for brazing Classification and technical delivery conditions EN 2174, Aerospace series Heat resisting alloy FE-PA2602 (X4NiCrTiMoV26-15) Solution treated and prec
23、ipitation treated Forgings De 100 mm Rm 850 MPa 1)EN 2175, Aerospace series Heat resisting alloy FE-PA2602 (X4NiCrTiMoV26-15) Solution treated and precipitation treated Sheet strip and plate 0,5 mm a 10 mm Rm 850 MPa 1)EN 2177, Aerospace series Heat resisting alloy FE-PA2501 (X4NiCrMoTi43-13) Soluti
24、on treated and precipitation treated Forgings De 100 mm 1)EN 2178, Aerospace series Heat resisting alloy FE-PA2501 (X4NiCrMoTi43-13) Solution treated and precipitation treated Bar and section De 200 mm 1)EN 2278, Steel FE-PM37 900 MPa Rm 1 100 MPa Bars De 150 mm Aerospace series 2)EN 2279, Steel FE-
25、PM37 900 MPa Rm 1 100 MPa Forgings De 150 mm Aerospace series 2)EN 2280, Steel FE-PM37 900 MPa Rm 1 100 MPa Sheets a 6 mm Aerospace series 2)1) Published as ASD-STAN Prestandard at the date of publication of this standard (www.asd-stan.org). 2) Published as ASD-STAN Standard at the date of publicati
26、on of this standard (www.asd-stan.org). BS EN 4632-004:2012EN 4632-004:2012 (E) 5 EN 2465, Aerospace series Steel FE-PA3901 (X2CrNi18-9) Softened 450 MPa Rm 680 MPa Bar for machining 4 mm De 100 mm EN 2466, Aerospace series Steel FE-PA3901 (X2CrNi19-11) Softened Forgings De 100 mm EN 2467, Aerospace
27、 series Steel FE-PA3901 (X2CrNi18-9) Air melted Softened Plate, sheet and strip 0,4 mm a 20 mm 520 MPa Rm 670 MPa EN 2468, Steel FE-PA11 Softened Tubes 0,5 mm a 5 mm Aerospace series 2)EN 2469, Aerospace series Steel FE-PA3901 (X1CrNi18-10) Air melted Softened Wires 0,4 mm D 12,5 mm 450 MPa Rm 650 M
28、Pa EN 2815, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precipitation treated Bar for machining a or D 200 mm Rm 965 MPa EN 2816, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precipitation tr
29、eated Forgings a or D 200 mm Rm 965 MPa 1)EN 2817, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precipitation treated Bar for machining a or D 200 mm Rm 1 070 MPa EN 2818, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remel
30、ted Solution treated and precipitation treated Forgings a or D 200 mm Rm 1 070 MPa EN 2821, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precipitation treated Bar for machining a or D 200 mm Rm 1 310 MPa EN 3160, Aerospace series Steel FE-PM3801
31、(X5CrNiCu17-4) Air melted, solution treated and precipitation treated Bar a or D 200 mm Rm 1 310 MPa EN 3161, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) Air melted, solution treated and precipitation treated Bar a or D 200 mm Rm 930 MPa EN 3162, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) A
32、ir melted, solution treated and precipitation treated Sheet and strip, a 6 mm Rm 930 MPa EN 3357, Aerospace series Steel FE-PM1503 (X3CrNiMoAl13-8-2) Vacuum induction melted and consumable electrode remelted Solution treated and precipitation treated Bar for machining a or D 150 mm 1 200 MPa Rm 1 40
33、0 MPa 1)EN 3358, Aerospace series Steel FE-PM1503 (X3CrNiMoAl13-8-2) Vacuum induction melted and consumable electrode remelted Solution treated and precipitation treated Bar for machining a or D 150 mm Rm 1 400 MPa 1)EN 3359, Aerospace series Steel FE-PM1503 (X3CrNiMoAl13-8-2) Vacuum induction melte
34、d and consumable electrode remelted, softened, forging stock a or D 300 mm EN 3361, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted, solution treated and precipitation treated, sheet and strip a 6 mm 1 070 MPa Rm 1 220 MPa EN 3365, Aerospace series Steel FE-PM3901 (X15C
35、rNi17-3) Air melted, softened, forging stock a or D 300 mm BS EN 4632-004:2012EN 4632-004:2012 (E) 6 EN 3468, Aerospace series Steel FE-PA13 Softened 500 Rm 700 MPa Forgings De 100 mm 1)EN 3469, Aerospace series Steel FE-PM1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precip
36、itation treaded Forgings a or D 200 mm Rm 1 310 MPa 1)EN 3470, Aerospace series Steel FE-PM1503 (X3CrNiMoAl13-8-2) Vacuum induction melted and consumable electrode remelted Solution treated and precipitation treated Forgings a or D 150 mm 1 200 MPa Rm 1 400 MPa 1)EN 3479, Aerospace series Steel FE-P
37、M1802 (X5CrNiCu15-5) Consumable electrode remelted Solution treated and precipitation treated Plate 6 mm 1,67 in pulsed 521. Table 18 Recommendations for brazing and diffusion bonding AWS acronym and corresponding EN ISO 4063 reference number State before assembly Assembly temperatureC PJHT Filler m
38、etal Flux Degree of brazeability or weldability aComments family form 922 Softened 1 050 None Ni foil, powder, sintered ruban None 1 Vacuum at 1,3103Pa then Ar injection under partial pressure 6,5 PaLBBW 913 Softened 1 050 None Ni foil, powder, sintered ruban None 1 aIf two degrees are indicated, th
39、e responsible person shall select the degree that is most appropriate for the definition of the assembly. BS EN 4632-004:2012EN 4632-004:2012 (E) 28 8.7 X12CrNiCoMoW21-20 8.7.1 Designation EN 4570, EN 4571, EN 4572, EN 4573, EN 4574, EN 4575 : X12CrNiCoMoW21-20 EN 10027-1 : Z12CNKDW20 ASD-STAN : FEP
40、A49018.7.2 Chemical composition See Table 19. Table 19 Typical chemical composition (w %) Grade Fe C Cr Ni Co Mo W Mn Nb Si Cu N P S X12CrNiCoMoW21-20 Base 0,08 0,16 20,0 22,5 19,0 21,0 18,521,02,503,502,003,001,002,000,751,25 1,00 0,50 0,10 0,20 0,020 0,0158.7.3 Structure Heat resisting austenitic 8.7.4 Particular characteristics None. 8.7.5 Forms Forgings (EN 4570, EN 4574) Bar and section (EN 4571, EN 4573) Sheet and strip (EN 4572) Sheet and plate (EN 4575). See Table 20.
