1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2016 07 25 Released L. Sinclair, NA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 3 FABRIC, NYLON FLOCKED, VINYL (PVC) FOIL, WSS-M2F216-A1 FLOOR MAT BINDING 1. SCOPE The material defined by thi
2、s specification is a nylon based fabric of uniform construction. 2. APPLICATION This specification was released originally for floor mat binding. 2.1 LIMITATIONS This material can not be used anywhere other than floor mat bindings. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the
3、 use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer.
4、3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.3 PE
5、RFORMANCE CRITERIA In addition to the requirements listed herein, the material must also meet the requirements of WSS-M8P24-A/ Latest, Performance, Floor Mat Edging. 3.4 FABRIC CONSTRUCTION 3.4.1 Weight (FLTM BN 106-01) PVC 370 +/- 19 g/m2 Flocking 130 +/- 30 g/m2 Total 500 +/- 30 g/m2 3.4.2 Thickne
6、ss 1.10 +/- 0.1 mm 3.5 COMPOSITION (ASTM D 629) ENGINEERING MATERIAL SPECIFICATION WSS-M2F216-A1 Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 B Surface 100% PVC A Surface 100% Nylon Flock 3.6 YARN CONSTRUCTION (ASTM D 1244) A Surface staple length 0.75 +/- 0.1 mm, 1.7 dtex3.7 METHOD OF
7、DYING Piece 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 TYPICAL PHYSICAL PROPERTIES 4.1.1 Tensile Strength (ISO 1421) War
8、p 13 daN/5 cm Fill 13 daN/5 cm 4.1.2 Elongation (ISO 1421) Warp 200 % Fill 200 % 4.1.3 Tear Strength (ISO 4674) Warp 0.5 daN Fill 0.5 daN 4.1.4 Stretch and Set (SAE J855) Warp 35 % Fill 50 % 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of
9、interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Ma
10、terial Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.3
11、 SUPPLIERS ONGOING RESPONSIBILITY ENGINEERING MATERIAL SPECIFICATION WSS-M2F216-A1 Copyright 2016, Ford Global Technologies, LLC Page 3 of 3 All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material
12、 originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of
13、a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept
14、 until Job 1. 4.4 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS
