1、1=1MIL-D-23160D(NAVY)30 Aoril 1992SUPERSEDINGMIL-D-23140C(NAVY)21 January 1985(See 6.7)t41LITARY SPECIFICATIONDRAWINGS , INSTALLATION CONTROL, FORELECTRONIC EQUIPMENTThis specff Lcation is approved for use by the Department of the Navy,and is available for use by all Departments and Agencies of theD
2、epartment of Defense.1. SCOPE1.1 m. TIIis specification covers the preparation and acquisitionof installation control drawings for electronic equipment (see 6.3)2. APPLICABLE DOCUMENTS2.1 Government documents.2.1.1 Svecif ications. standards and handbooks. The following specifi-cations, standards an
3、d handbooks, form a part of this document to the extentspecified herein. Unless otherwise specified, the issues of these documents arethose listed in the issue of the Department of Defense Index of Specifications andStandards (DODISS) and supplement thereto, cited in the solicitation (see 6.2) .SPEC
4、IFICATIONSFEOSRALL-P-519 - Plastic Sheet: Tracing, Glazed and Matte Finish.MILITARYMIL-S-901 - Shock Tests, H. 1. (High-Impact) Shipboard Machi-nery, Equipment and Sys terns, Requirements for.I 1Beneficial comments (recommendati.ona, additions , deletions) and any pertinentdata which may be of use i
5、n improving this document should be addressed to:Commander, Naval Sea Systeme Command, SEA 55z3, Department of the Navy,Washington, DC 20362-5101 by using the self-addressed Standardization DocumentImprovement Proposal (DD Form 1426) appearing at the end of this document orby letter.AKSC No. N6684 A
6、REA DRPRPIS TR18 UTION STATEW3NT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-23140D(NAVY)MIL-D -5480 -MIL-M-9868 -MIL-N-25027 -MIL-D-28000 -STANDARDSMILITARYDOD- STD -100 -MIL-STD-12
7、9 -MIL-sTD-167-1 -MIL-sTD-167-2 -MIL-STO-242 -MIL-STD-419 -MI L-STD-131O -MIL-STD-1399 -Section 102 -Section 300 -Section 390 -Section 532 -Section 702 -MIL-STD-1683 -MIL-STD-1806 -HANDBOOKMILITARY1.IIL-HDBK-22S -Data, Engineering and Technical: ReproductionRequirements For.Microfilming of Engineeri
8、ng Documents. 35UIUI,Requirements For.Nut, Self-Locking, 250” F, 450” F, and 800” F.Digital Representation for Communication ofProduct Data: ICES Application subsetsEngineering Drawing PracticesMarking for Shipment and Storage.Mechanical Vibrations of Shipboard Equipment(Type I - Environmental and T
9、ype II -Internally Excited)Mechanical Vibrations of Shipboard Equipment(Reciprocating Machinery and PropulsionSystem and Shafting) Type III , IV, and V.Electronic Equipment Parts, Selected StandardsSwitches.Cleaning, Protecting and Testing Piping, Tubingand Fittings for Hydraulic Power TransmissionE
10、quipment.Shipboard Bonding, Grounding, and Other Tech-niques for Electromagnetic Comparability andSafety.Interface Standard for Shipboard SystemsLow Pressure Dry Air Service For Surface ShipsElectric Power, Alternating Current.(Metric)Electric Power, Direct Current, (Other TSWUIShips Battery) For Su
11、bmarines. (Metric)Cooling Water for Support of ElectronicEquipment. (Metric)Synchro Data Transmission.Connectors and Jacketed Cable, Electric,Selection Standard for Shipboard Use”.Marking Technical Data Prepared by or for theDepartment of DefenseSynchros Description and Operation2.1.2 Other Governme
12、nt documents. drawinm and uublicati ons The f0llowingother Government documents, drawings and publications form a part of this documentto the extent specified herein. Unless otherwise specif fed, the issues are thosacited in the solicitation.e.,2Provided by IHSNot for ResaleNo reproduction or networ
13、king permitted without license from IHS-,-,-MIL-D-23140D(NAVY)a71PUBLI CATIONSH4/H8 cataloging Handbook H4/H8, Commercial andGovernment Entity (CAGE)DOD-5220 .22-M - Industrial Manual for Safeguarding Class ifledInformation.(Application for copies may be obtained from the Superintendent of Docu-ment
14、s, Government Printing Off ice, Washington, DC 20402. )NAVAL SRA SYSTEMS COMMAND (NAVSEA)S-9086 -S4-STM-000/CH-556 - Naval Ships Technical Manual, HydraulicEquipment (Power Transmission andControl) .s-0300 -AT-cTP-olo/EsL - Standard Electrical Syinbol List.O967-LP-OOO-O11O - Electronics Installation
15、 and MaintenanceBook Installation Standards.0967 -LP-OOO-0130 - Electronics Installation and MaintenanceBook, Test Methods and Practices .S9407-AB-HBK-O1O - Handbook of Shipboard ElectromagneticShielding Practices.(Copies of specifications, standards, and publications required by con-9traccors in co
16、nnection with specific acquisition functions should be obtainedfrom the contracting activity or as direoted by the contracting officer. )2.2 pOn-Government Publications. The following documents form a part ofthis document to the extant specified herein. Unless otherwise specified, theissues of the d
17、ocuments which are DOD adopted are those listed in the issue of theDODISS cited in the solicitation. Unless otherwise specified, the issues of thedocuments not listed in the DODISS are the issues of the documents cited in thesolicitation (see 6.2) .AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI )ANSI Y
18、32. 10 - Graphic Symbols for Fluid Power Diagrams.(DoD adopted)(Application for copies should be addressed to the American NationalStandards Imtitute, 1430 Broadway, New York, NY 1001S. )IUNIFORM CLASS IFICATION COMMITTEE AGENTUniform Reight Classification Ratings, Rules and Regulations(Application
19、for copies should be addre6sed to the Uniform Classifica-tion Committee Agent, Tariff Publication Officer, Room 1106, 222 South RiversidePlaza, Chicago, IL 60606. )10 (Industry association specifications and standards are generally availablefor reference from libraries. They are also distributed amo
20、ng technical groupsand using Federal agent lea. )3IProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-23140D(NAVY)2.3 Order of Drecedence. In the event of a conflict between the text of ethis document and the references cited herein (except for re
21、lated associateddetail specifications, specification sheets, or IIS standards) , the text of thisdocument takes precedence. Nothing in this document, however, supersedesapplicable laws and regulations unless a specific exemption has been obtained.3. RSQUIRSMENTS3.1 Iatall atfon control draw-. Instal
22、lation control drawings shall bein accordance with this specification and shall set forth the electrical, phy-sical, mechanical, and interface, data for installing activities to develop plansand drawings for the ins tallation of electronic equipment.3.2 l?xeuarati n Installation control drawings sha
23、ll be prepared inaccordance with the eneral drawing practices outlined in DOD- STD -100, except that .“Roll” size sheets shall not be used. All sheets of multisheet data elementsshall be the. same size (see 3.3.4). Installation control drawings shall containthe information described in 3.3.6 through
24、 3.3.15. The referenced figuresprescribe the format for the information required. The quantitative values listedthereon are explanatory only. Finished installation control drawings shallcontain the requirements of the installed equipment.3.2.1 umbe Ilnals or duplicateRI reference to subordinate docu
25、ments for revision descrip-tion is not permissible.3.2.11.1 -. The contractor shall mark up a copy of the existingdrawing supplied to the contractor by the Government, to reflect the currentequipment conf fguration.3.2.11.2 ComDl ete. The contractor shall prepare a new original whenspecified.3.3 Con
26、tent and format. Installation control drawing content and formatshall be developed in consonance with the progression of equipment design andproduction as specified herein.3.3.1 Installation desire reservation date. Installation design reserva-tion data shall contain the information listed below and
27、 as specified (see 6.3).The preliminary information provided shall permit a design agent or shipyard toinitiate installation planning for equipment to be installed. Subsequent drawingsshall indicate changes made to these data.(a) Total equipment weight and space requirements.(b) Total equipment elec
28、trical power requirements including type(from sections 300 and 390 of “DOD-STD -1399) , power, voltage,frequency, power factor, phase (single or three phase) .(c) Auxiliary cooling and dry air requirements.(d) Hydraulic fluid power requirements.(e) AIIy unusual requirements such as size of equipment
29、 not permittingentry through ship doors or hatches.(f) Total heat dissipation expressed in watts.3.3.2 neliminarv installation control drawings. Preliminary installationcontrol drawings shall consist of the drawings listed in 3.3.4, as applicable,and as specified (see 6.3) . These drawings shall pro
30、vide information which issufficiently accurate and complete to permit design agents or shipyards to startinstallation design with no major changes expected which may affect installationdesign.3.3.3 Proposed final installation control drawinws. Proposed finalinstallation control drawings shall consis
31、t of the data elements listed in 3.3.4,as applicable and as specified (see 6.3) . These drawings shall be prepared afterall discrepancies on the preliminary drawings have been corrected and informat ionis final, accurate, and complete.3.3.4 Final installation control drawinm. Final installation cont
32、roldrawings shall consist of the following elements, as applicable and as specified(see 6.3). I%ese drawings shall provide information which is final, accurate, andcomplete, to permit des$ agents or shipyards to proceed with constructionpanding receipt of equipment.(a) Drawing list (see 3.3.6)(b) Bl
33、ock diagram (see 3.3.7) .(c) Outline and installation drawing (see 3.3 .8) .6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.DIIa71MIL-D-23140D(NAVT)(d) Auxiliary cooling diagram (see 3.3. 9).(e) Auxiliary dry gas diagram (see 3.3. 10) .(f) Cable ru
34、nning sheets (see 3.3. 11).(g) Summary list of installation material (see 3.3. 12).(h) Radio frequency (RF) transmission line diagram (see 3.3. 13) .(i) Hydreulic fluid piping diagram (see 3.3. 14).(j) Synchro data transmission drawing (. 3.3. 15).3.3.5 Blocks. Blocks on preliminary, proposed final,
35、 and final drawingsshall be as follows:3.3.5.1 Title blocks.or 2 and as follows:(a) Show drawingcompositionTitle blocks shall be in accordance with figures 1titles in tbe following form. See tiOD-STO-100 forof item name.ITEM NAMETYPE DESIGNATIONTVPE OF DRAWING(b) See figures 10 through 19 for exampl
36、es of title lettering.(c) Unless otherwi,e specified (see 6.2.), the Drawing No. block isfor Government use.(d) The other blocks are self-explanatory.3.3.5.2 si nature blocks. Signature blocks shall be as shown on figures 1or 2 and as follows:(a) In the top block enter the Naval Sea Systems Command
37、(NAVSBA)sigmature or Space and Naval Warfare (SPAWAR) sfgnature, asapplicable, unless otherwise specified (see 6.Z) .(b) The acquis ition manager, code, and date blocks are for Procuringactivity use.3.3.5.3 Valid ation blocks. Validation blocks shall be as shown on figures1 or 2 and as follows:(a) T
38、he Information and Data Validation block Is for the “contractor 1ssignature and date of signature.(b) The tvo lower blocks are for Navy use.3.3.5.6 Kevision block.q. Revision blocks shall be in accordance withfigures 1 or 2. These blocks shall be used as specified in DOD- STD-1OO.3.3.5.5 Mater,”!. .
39、 . . .“(a) Single line blocks for units to be supplied with the equipmentplus other items required to complete the installation. Thisincludes items such as racks, junction boxes, motor generatorsisolation transformers, antennas , and hydraulic units. Blocksc- .t.- . - =7.: :5:= :=: shell bc arr=ngcd
40、 in a logical. . relationship to each other and shall meet the following require-ments:(1) The complete nomenclature and reference designationfor each unit shall be shown.(2) The reference designations for external receptacle con-nectors shall be shown and associated with their cables.(3) Where stan
41、dard electrical items such as junction boxes,transformers, and switches, are used, the standard symbolnumbers and types in accordance vi th NAVSSAS0300-AT-CTP- 010/ESL shall be shown.(6) The blocks for units , junction boxes, motor generators, dsimilar items shall be limited to those required. by th
42、isequipment. Cables and transmission lines going to other8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-xIL-D -23140 D(NAVY)(b)equipment shall he shown as going to the first interfaceonly. These interfaces shall be identified hy name, hutblocks sha
43、ll not be shown for them.(5) Units and items to he supplied with the equipment shall beidentif fed as supplied with equipment (SWE) .Cables and RF transmission lines which interconnect units, i-terns,and ocher equipment, shall be shown by single lines from theirorigins to their destinations.(1) Each
44、 cable and RF transmission line shall be identified byNavy cable designation (for example R-EA(50) , R-RR(37),R-RY/Q(6), type, and siza.a. These Navy cables designations will be -sis-.d by theGovernment. The numerical part of each designationwill be shown in parentheses. A note will state thatthe nu
45、mbers in parentheses are for reference onlyand that the actual numbers are to be assigned by theinstalling activity.b. The size will not be shown for cables to ships power.A note will state that the sizes of these cables areto be determined by the installing activities.c. Cable designations of the a
46、bove type for cablesto ships power will not be shown. These cables willbe identified by “W.” numbers. A note will state thatthe cable designations for these cables are tobe assigned by the installing activity, except whenspecified by the acquisition activity.d. Cable designations and UW. numbers sha
47、ll be keyedto the ones shown on the cable running sheets.(2) Each cable and RF transmission line (excluding waveguide)except those to power will he identified by itselectromagnetic compatibility category and group inaccordance with NAVSSA s9407-AR-HSK-O1O.a. Show the category only for cables to ship
48、s power.Indicate that the gtoups are to be determined by theinstalling activity after the sizes have been deter-mined.b. Indicate that the installing activity may have tochange group numbers of categoiy S1, S2, and S4cables in process of adding conduit to achieve therequired isolation between cables
49、.c. Provide des Lgn performance sensitivities and frequencypassbands of equipments connected to suscepter cablesin categories S1, S2, and s4. Identify the cables towhich these sensitivities and passbands apply.(3) The types and sizes of cables going to interfacing equip-ment shall be shown. Cables between interfacing equip -9IProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-141L-D-23140D(NAVT)Ime
