1、I - MIL-STD-1386 -32 81 W 7777733 0072687 7 W - 98-37-07 MIL-STD-1386-32 MILITARY STANDARD (NAVY) LOADING QF HAZARDOUS MATERIALS AND ASSOCIATED ITEMS IN MILVAN CONTAINERS ROCKET HEAD, 5“MK 24 OR MK 32 AND MODS (ZUNI) FLEET ISSUE UNIT LOAD I MAY IV4 UNIT LOAD DATA SEE TABLES I ANO il UNIT LOAD DRAWIN
2、G . WR-54/33 Doi HAZARD CLASSIFICATION . , EXPLOSIVES A COAST GUARD CWS Pn AUTHORIZED FOR CONTAINER-ON- APPROVED BY FLAT-CAR (COFC), CONTAINERSHIP AND MOVEMENT ABOARD DEPOT BUREAU OF EXPLOSIVES DATE 7 (NON-PUBLIC) ROADS ONLY. / / I LYW 4/3/7g SIGNANRE /cy& ,dwHL ORIGINATOR . SIGNATURE TEdNiCAL DIREC
3、TION AGENT ITDAI DAIE NAVAL WEAPONS HANDLING LABORATORY AIRSY OM 8Y DIREETION DATE NA D EARLE, NEW JERSEY PAGE 1 OF 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1386-32 (NAVY) GENERAL NOTES I. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FO
4、R LOADING THE MILVAN CONTAINER WITH FLEET ISSUE UNIT LOADS OF 5“ ZUNI ROCKET HEADS, MK 24 8 MODS OR MK 32 8 MODS IN PALLET ADAPTERS MK I I MOD O OR MOD I. THE UNIT LOAD SHALL BE PALLETIZED IN ACCORDANCE WITH WR-54/33. THE MILVAN SHALL BE EQUIPPED WITH A MECHANICAL LOAD-BRACKING SYSTEM THAT MEETS THE
5、 REQUIREMENTS OF THE BUREL3 OF 2. EXPLOSIVES PAMPHLET 6C. 3. IN ADDITION TO THE BELT RAILS REQUIRED BY PAMPHLET 6C, THE MILVAN CONTAINER HAS BELT RAILS AT THE 72AND 83 INCH HEIGHTS FROM THE CONTAINER FLOOR, -I WHEN POSITIONING CROSSMEMBERS, MAKE A VISUAL CHECK TO EN- SURE THAT THE CROSSMEMBERS ARE L
6、OCKED SECURELY IN PLACE. 4. CONTAINERS ARE EQUIPPED WITH 25 CROSSMEMBERS. UNUSED CROSShiEHBERS MUST REMAIN WITH THE CONTAINER AND SHALL BE FASTENED INTO THE BELT RAILS FOR SHIPMENT, WHEN THE VOID BETWEEN THE CROSSMEMBER AND THE SEPARATOR GATE IS GREATER THAN ONE INCH, USE FILL MATERIAL TO SHIM BETWE
7、EN CROSSMEMBER AND GATE, AS SHOWN IN DETAIL J, PAGE 4. SWAY BRACE, DETAIL H, IS ASSEMBLED IN PLACE. PIECE 1, IS POSITIONED INBOARD OF THE OUTER LEGS OF THE PALLET SKIDS AND PIECE 2 IS POSITIONED AGAINST THE PALLET LEGS. NAIL PIECE 2 TO PIECE 1 WITH THREE Iod NAILS PER JOINT. CUT PIECE 3 TO FIT BETIV
8、EEN PIECES 2AND NAIL TO PIECE 1 WITH THREE Iod NAILS. WIDTH OF SWAY BRACE, DETAIL C, SHALL BE SUFFICIENT TO BEAR AGAINST UNIT LOAD AND SIDE WALL OF CONTAINER. TIVIST TIE EACH END OF SWAY BRACE TO CROSSMEMBER WITH TWO LOOPS OF 16 GA. WIRE, EACH BAY Of ROCKET HEADS IS TOMFAED DOWN WITH NI0 1 1/4 X ,03
9、5 STEEL STRAPS. THE STRAPS ARE ATTACHED TO ALTERNATE CROSSMEMBERS AS SHOWN IN THE SECTION DETAILS ON PAGES 2 AND 4. LOCATE SEALS WITH A CROSSMEMBER BEWEEN THE SEAL AND THE STRAP AS SHOWN IN DETAILS N AND P, ON PAGE 6. SECURE EACH END OF THE STRAP WITH ONE SEAL WITH WO PAIR OF NOTCHES PER SEAL, OR WO
10、 SEALS BUTTED TOGETHER WITH TWO PAIR OF CRIMPS PER SEAL. 5. 6. 7. 8. 9. APPLICABLE MATERIAL SPECIFICATIONS: DUNNAGE LUiMBER -FED. SPEC. MM-L-751 NAILS - FED. SPEC. - FF-N-105, TYPED, STYLE IO, COMMON BRIGHT STRAP - FED. SPEC, -QQ-S-781, TYPE I, CLASS A IO. AFTER BLOCKING AND BRACING HAS BEEN INSPECT
11、ED, ATTACH SHIPPING DOCUMENTS INSIDE THE CONTAINER IN AN ACCESSIBLE AREA, CLOSE AND SEAL THE CONTAINER DOORS AND ATTACH APPLICABLE PLACARDS TO THE OUTSIDE OF THE CONTAINER FOR THE APPROPRIATE MODE OF TRANSPORTATION AS PRESCRIBED IN OP 2165 (VOL. i). COEC AND CONTAINERSHIP ONLY I. THE CONTAINER LOADS
12、 CONSIST OF 15 UNIT LOADS OF ROCKET HEADS, MK 32 AND MODS AS DEPICTED ON PAGE 3, OR 14 UNIT LOADS OF ROCKET HEADS, MK 24AND MODS AS DEPICTED ON PAGE 5. THE CONTAINER MUST BE LOADED AND DUNNAGED IN ACCORDANCE WITH THIS DOCUMENT. (WARNINOI BECAUSE THE WEIGHT LOADED INTO THIS CONTAINER EXCEEDS 34,030 L
13、BS, THE MILVAN CHASIS CANNOT BE USED TO TRANSPORT THE LOADED CONTAINER ON PUBLIC HIGHWAYS. THE LOADED CONTAINER MAY BE TRANSPORTED OVER DEPOT ROADS USING MILVAN CHASIS EQUIPPED WITH DOUBLE BOGIES OR COMERCIAL EQUIPMENT OF APPROPRIATE CA PACI TY. t. 2. WHEN SHIPPING THE LOADED MILVAN CONTAINER COK, T
14、HE FLAT CAR SHALL MEET THE REQUIREMENTS OF BUREAU OF EXPLOSIVES PAMPHLET 6C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1386 -32 83 W 7777733 O072687 2 - TABLE I MIL-STO-1386-32 (NAVY) I ROCKET HEAD. MK 32 AND MODS (ZUNI) I DIMENSIONS I
15、i . I i I I I I 48 L x MOD O 2,522 37,830 44,839 MOD I 2,466 I 36, I 43,9Fp I1OWxlo 1/4 H I “* I SEE DETAIL PAGE 4 W . ROCKET HEAD ,MK 32 AND MODS COFC L CONTAIMERSHlf ?AOC 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L3b -32 L W 97777LL
16、 0072670 7 m SECTION -E (TYPICAL OF DOUBLE TIERED AM) CROSSMEMBER OF MY AT TH CROSSMEMER HEIGHT INDICATED. SEE IMTAIL P, PAGE 6. *FAR END OF STIAP IS ATTACHED TO FORWARD DETAIL SEPARATOR OAR 2 REQUIRED 16 GA TIE WIRE FILL MATERIAL SEE GENERAL NOTE 5 SWAY BRACE 7 REQUIRED rt, BE ASSEMBLED IN PLACE SE
17、E NOTE A. PAGE 2 _. - . PAGE 4 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II MIL-STD-1386-32 (NAVY) I ROCKET HEAD, 5” MK ZQAND MODS I. IN PALLET ADAPTER MOD O I MODI WEIGHT 1 NETzlYHT I GROSSWEIGHT DlhLNSIONS I (z:.) I UNIT LOAD CONTAINE
18、R CONTAINER IL69 (Las) ?AE 5 ROCKET HEAD,MK 24 AND MODS COFC & CONTAtNERSHIP Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L386 -32 81 W 77777LL 0072692 2 MIL-STD-1386-32 (NAVY) 4 SEPMATOR GATE 1 REQUIRED SEE GENEWL NOTE 8, PAGE 2 DETAIL DE
19、TAIL 8 TYPICAL WHERE CROSSMEMMR CAN BE USED BENJEEN ATTACHMENT POINT AND SEAL. REVIEW ACTIVITY: NAVY - os, As PAGE 6 PREPARING ACTIVITY: NAVY - O (PROJECT NO. 8140-N216) * U.S. GOVERNMENT PRINTING OFFICE: 1974-71 31 54/5785 - a I- . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
