1、AEROSPACE STANDARD (R) FITTING ASSEMBLY, ELBOW 90, REDUCER ANDNONREDUCER, INTERNAL FLARE TO FLARED TUBE Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica
2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE Technical Standards Board
3、 Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”
4、SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. AS4407 ISSUED 1995-03REVISED 2011-02THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV.AFEDERAL SUPPLY CLASS 4730 AS4407SHEET 1 OF 5REV. A
5、PROCUREMENT SPECIFICATION: /4/ AS4841SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4407ARATIONALE CADMIUM NOTICE NOTE ADDED, NADCAP QML NOTE UPDATED, CANCELLED REFERENCE DOCUMENTS REPLACED WITH ACTIVE DOCUMENTS, 2024 ALUMINUM
6、 ALLOY MATERIAL MADE INACTIVE FOR NEW DESIGN, AND DIMENSION ACROSS WRENCH PADS DIRECTLY SPECIFIED ON DRAWING. 90q0 r 2q30 FORSIZE 03 AND SMALLERr 1q30 FOR SIZE 04AND LARGERPORT 1FITTING ENDPER AS1708STYLE BRETAINING WIREPER AS1791LOCATION OFIDENTIFICATION /5/RETAINED NUTPER AS4370PORT 2FITTING END P
7、ER AS4395STYLE G IF NON-REDUCERSTYLE E EXCEPT HEX IF REDUCER(T1)XVACROSSWRENCH PADSC(T2)W MIN WALLTHICKNESS OFCENTER BODYSECTIONABFIGURE 1 - FITTING ASSEMBLY, ELBOW 90 WIRE SHALL BEINSTALLED TODIMENSION D /10/D MINAASECTION A - AFIGURE 2 - INSTALLATION, RETAINED NUT AND RETAINING WIRE INACTIVE IN PA
8、RT /18/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4407SHEET 2 OF 5REV. A(R) FITTING ASSEMBLY, ELBOW 90, REDUCER AND NONREDUCER, INTERNAL FLARE TO FLARED TUBE TABLE 1 - DIME
9、NSIONS AND WEIGHTS BASIC NO. AS4407/17/SIZE CODE (NOMINAL TUBE SIZE)T1, T2 THREADPERAS8879 C D V W LB/EAAPRROXREF ALUMLB/EAAPPROXREF CRESLB/EAAPPROXREF TI02 .125 .3125-24 UNJF .058- .065 .045 .297- .314 .090 .017 .049 .028 03 .188 .3750-24 UNJF .121- .128 .045 .360- .377 .100 .023 .067 .038 04 .250
10、.4375-20 UNJF .168- .175 .045 .423-. 440 .110 .030 .086 .049 05 .312 .5000-20 UNJF .230- .237 .045 .485- .502 .120 .034 .098 .056 06 .375 .5625-18 UNJF .293- .301 .045 .547- .565 .120 .051 .147 .084 08 .500 .7500-16 UNJF .387- .395 .055 .735- .753 .150 .092 .268 .154 10 .625 .8750-14 UNJF .480- .488
11、 .063 .860- .878 .170 .141 .409 .234 12 .750 1.0625-12 UNJ .604- .614 .095 1.047-1.065 .185 .235 .681 .390 16 1.000 1.3125-12 UNJ .839- .851 .125 1.292-1.317 .205 .386 1.120 .641 20 1.250 1.6250-12 UNJ 1.073-1.086 .155 1.605-1.630 .240 .661 1.920 1.099 24 1.500 1.8750-12 UNJ 1.307-1.320 .180 1.855-1
12、.880 .250 .878 2.550 1.461 32 2.000 2.5000-12 UNJ 1.776-1.791 .180 2.542-2.572 .350 1.151 3.340 1.913 TABLE 2 - LEG LENGTH A SIZE OF PORT #1 FORG. SIZE/8/02FORG. SIZE/8/03FORG. SIZE/8/04FORG.SIZE/8/05FORG.SIZE/8/06FORG.SIZE/8/08FORG.SIZE/8/10FORG.SIZE/8/12FORG. SIZE/8/16FORG. SIZE/8/20FORG.SIZE/8/24
13、FORG.SIZE/8/3202 .658 .686 .743 .767 .884 .924 1.100 1.157 1.268 1.521 1.521 2.031 03 - .672 .555 .587 .649 .743 .838 .931 1.056 1.213 1.338 2.015 04 - - .602 .633 .695 .789 .883 .976 1.101 1.258 1.383 1.890 05 - - - .675 .737 .831 .925 1.018 1.143 1.300 1.425 1.937 06 - - - - .821 .915 1.009 1.102
14、1.227 1.384 1.509 1.968 08 - - - - - 1.023 1.117 1.210 1.334 1.491 1.616 2.130 10 - - - - - - 1.167 1.260 1.383 1.540 1.665 2.098 12 - - - - - - - 1.224 1.348 1.505 1.630 2.09816 - - - - - - - - 1.387 1.524 1.649 2.150 20 - - - - - - - - - 1.571 1.696 2.243 24 - - - - - - - - - - 1.776 2.28632 - - -
15、 - - - - - - - - 2.442 TABLE 3 - LEG LENGTH B SIZE OF PORT #2 FORG. SIZE/8/02FORG. SIZE/8/03FORG. SIZE/8/04FORG.SIZE/8/05FORG.SIZE/8/06FORG.SIZE/8/08FORG.SIZE/8/10FORG.SIZE/8/12FORG. SIZE/8/16FORG. SIZE/8/20FORG.SIZE/8/24FORG.SIZE/8/3202 .757 .789 .789 .843 .946 1.033 1.135 1.232 1.341 1.544 1.685 2
16、.169 03 - .820 .811 .874 .977 1.064 1.166 1.263 1.372 1.575 1.716 2.200 04 - - .882 .945 1.048 1.135 1.237 1.334 1.443 1.646 1.787 2.271 05 - - - .945 1.048 1.135 1.237 1.334 1.443 1.646 1.787 2.271 06 - - - - 1.054 1.141 1.243 1.340 1.449 1.652 1.793 2.277 08 - - - - - 1.242 1.344 1.441 1.555 1.753
17、 1.894 2.378 10 - - - - - - 1.445 1.542 1.651 1.854 1.995 2.479 12 - - - - - - - 1.648 1.757 1.960 2.101 2.58516 - - - - - - - - 1.804 2.007 2.148 2.632 20 - - - - - - - - - 2.054 2.195 2.679 24 - - - - - - - - - - 2.320 2.80432 - - - - - - - - - - - 3.054 Copyright SAE International Provided by IHS
18、 under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4407SHEET 3 OF 5REV. A(R) FITTING ASSEMBLY, ELBOW 90, REDUCER AND NONREDUCER, INTERNAL FLARE TO FLARED TUBE NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADM
19、IUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: A. DASH AS CODE LETTER: (1) BODY: TYPE 4130 STEEL FORGING OR BAR PER AMS6370 OR AMS-S-6758. (2) NUT: DASH AS CODE LETTER OF AS4370 (TYPE 4130 STEEL). (3) WIRE: PER AS1791 (CLASS 302 OR 305
20、 CORROSION RESISTANT STEEL). B. CODE LETTER D /18/: (1) BODY: TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS4133; OR TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6; OR 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS4339. (2) NUT: CODE LETTER D OF AS4370 (TYPE 2024 ALUMINUM ALLOY). (3) WIRE:
21、PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL). C. CODE LETTER J: (1) BODY: TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5639 OR AMS-QQ-S-763. (2) NUT: CODE LETTER J OF AS4370 (TYPE 304 CORROSION RESISTANT STEEL). (3) WIRE: PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL)
22、. D. CODE LETTER K: (1) BODY: TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5648 OR AMS-QQ-S-763. (2) NUT: CODE LETTER K OF AS4370 (TYPE 316 CORROSION RESISTANT STEEL). (3) WIRE: PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL). E. CODE LETTER S: (1) BODY: TYPE 347 CORROSION RESIST
23、ANT STEEL FORGING OR BAR PER AMS5646 OR AMS-QQ-S-763. (2) NUT: CODE LETTER S OF AS4370 (TYPE 347 CORROSION RESISTANT STEEL). (3) WIRE: PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL). F. CODE LETTER T: (1) BODY: TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. (2) NUT: CODE LETTER T OF AS4370 (TY
24、PE 6AL-4V TITANIUM ALLOY). (3) WIRE: PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL). G. CODE LETTER W: (1) BODY: TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141; OR 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124; OR 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. (2) NUT: CODE LETTER W OF AS437
25、0 (TYPE 7075 ALUMINUM ALLOY). (3) WIRE: PER AS1791 (CLASS 302 OR 305 CORROSION RESISTANT STEEL). 2. HEAT TREATMENT PER PROCUREMENT SPECIFICATION. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROS
26、PACE STANDARD AS4407SHEET 4 OF 5REV. A(R) FITTING ASSEMBLY, ELBOW 90, REDUCER AND NONREDUCER, INTERNAL FLARE TO FLARED TUBE 3. FINISH: A. DASH AS MATERIAL CODE LETTER: (1) BODY: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK. (2) NUT: DASH AS MATERIAL CODE LETTER OF AS4370 (CADMIUM PLAT
27、E, DYED BLACK). (3) WIRE: PER AS1791 (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). B. MATERIAL CODE LETTER D: (1) BODY: ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL. (2) NUT: MATERIAL CODE LETTER D OF AS4370 (ANODIC COATING, DYE BLUE). (3) WIRE: PER AS1791 (PASSIVATE AN
28、D COAT WITH DRY FILM LUBRICANT). C. MATERIAL CODE LETTER J: (1) BODY: PASSIVATE PER AMS2700, TYPE 6 OR TYPE 7. (2) NUT: MATERIAL CODE LETTER J OF AS4370 (PASSIVATED). (3) WIRE: PER AS1791 (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). D. MATERIAL CODE LETTER K: (1) BODY: PASSIVATE PER AMS2700, TYPE 6
29、 OR TYPE 7. (2) NUT: MATERIAL CODE LETTER K OF AS4370 (PASSIVATED). (3) WIRE: PER AS1791 (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). E. MATERIAL CODE LETTER S: (1) BODY: PASSIVATE PER AMS2700, TYPE 6 OR TYPE 7. (2) NUT: MATERIAL CODE LETTER S OF AS4370 (PASSIVATED). (3) WIRE: PER AS1791 (PASSIVATE
30、 AND COAT WITH DRY FILM LUBRICANT). F. MATERIAL CODE LETTER T: (1) BODY: ANODIZE PER AMS2488 TYPE 2 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486. (2) NUT: MATERIAL CODE LETTER T OF AS4370 (FLUORIDE PHOSPHATE CONVERSION COAT). (3) WIRE: PER AS1791 (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). G.
31、 MATERIAL CODE LETTER W: (1) BODY: ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2 DYED BROWN, DUPLEX SEAL. (2) NUT: MATERIAL CODE LETTER W OF AS4370 (ANODIC COATING, DYE BROWN). (3) WIRE: PER AS1791 (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). H. SUFFIX CODE LETTER U: (1) BODY: HIGH PURITY ALU
32、MINUM COAT PER PROCUREMENT SPECIFICATION. I. SUFFIX CODE LETTER N: (1) NUT: SUFFIX CODE LETTER N OF AS4370 (COAT WITH DRY FILM LUBRICANT). /4/ PROCUREMENT SPECIFICATION: AS4841 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFAC
33、TURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT .Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted with
34、out license from IHS-,-,-AEROSPACE STANDARD AS4407SHEET 5 OF 5REV. A(R) FITTING ASSEMBLY, ELBOW 90, REDUCER AND NONREDUCER, INTERNAL FLARE TO FLARED TUBE /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3 OR 15B. A. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MA
35、NUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS“, AND MATERIAL CODE LETTER. B. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE AS SPECIFIED IN THE PROCUREMENT SP
36、ECIFICATION FOR REDUCER CONFIGURATION. PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 7. WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSIONS SHALL CONFORM TO AS1376, TYPE 1. /8/ FORGING SIZE IS DETERMINED BY LARGEST PORT SIZE. 9. A CHANGE BAR (l) LOCATED IN THE LEFT MA
37、RGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS
38、 AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. /10/ ASSEMBLE AS4370 RETAINED NUT TO FITTING BODY WITH AS1791 RETAINING WIRE AS SHOWN IN FIGURE 2. THE RETAINED NUT SHALL BE FREE TO ROTATE AFTER ASSEMBLY. /11/ SAFETY WIRE HOLES PER SUFFIX CODE LET
39、TER L OF AS4370. 12. INTERPRETATION OF DRAWING PER ARP4296. 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. 14. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 15. DIMENSIONING AND TOLERANCING: ANSI Y14.5
40、M-1982. 16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30. /17/ EXAMPLE OF PART NUMBER: BASIC PART NUMBERMATERIAL CODE LETTER /1/SIZE CODE, TUBE SIZE OFPORT #2 IN .062 INCREMENTSSAFETY WIRE HOLES IN SWIVEL NUT /11/AS4407 W 08 06
41、 U LSIZE CODE, TUBE SIZE OFPORT #1 IN .062 INCREMENTSOPTIONAL CODE LETTER (HIGH PURITYALUMINUM COATED, ALUMINUM ONLY) /3/18/ INACTIVE MATERIAL CODE: PART NUMBERS WITH D MATERIAL CODE ARE INACTIVE FOR NEW DESIGN AS OF 2011/05. USE PART NUMBERS WITH W MATERIAL CODE LETTER FOR NEW DESIGN. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
