TIS 688-1987 Standard for rosin flux cored solder wires《松香焊剂钎焊丝标准》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

CSN 25 4065-1986 Screw gauges Solid NOT GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心非穿过型环首螺钉规 直径为1 8 - G 3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4066-1986 Screw gauges Minimum and maximum check plug for solid NOT GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 非穿过型实心环首螺钉规最小与最大检测插栓 直径为1 8 - G .pdf

CSN 25 4069-1986 Screw gauges Wear check plug for solid or adjustable NOT GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 非穿过型实心可调节环形耐磨量规的检查插塞，圆柱形导管螺纹，直径1 .pdf

CSN 25 4075-1987 Limit screw plug gauges Trapezoidal screw threads《止动螺钉插塞规 梯形螺纹》.pdf

CSN 25 4080-1987 Solid GO screw ring gauges Trapezoidal screw threads《实心穿过型环首螺纹规 梯形螺纹》.pdf

CSN 25 4081-1987 Minimum and maximum check plugs for solid GO screw ring gauge Trapezoidal screw threads《老式螺纹环规用最小化和最大化检查塞 梯形螺纹》.pdf

CSN 25 4084-1987 Wear check plug for solid and adjustable GO screw ring gauge Trapezoidal screw threads《实心可调节环首螺钉规耐磨检查插塞 梯形螺纹》.pdf

CSN 25 4090-1987 Solid NOT GO screw ring gauges Trapezoidal screw threads《非穿过型实心环首螺钉规 梯形螺纹》.pdf

CSN 25 4091-1987 Minimum and maximum check plug for solid NOT GO screw ring gauge Trapezoidal screw threads《实心非穿过型环首螺钉规的最小和最大检查插塞 梯形螺纹》.pdf