ASTM F1910-1998(2003) Standard Specification for Long Barbed Tape Obstacles《长的有倒刺带状障碍物的标准规范》.pdf
《ASTM F1910-1998(2003) Standard Specification for Long Barbed Tape Obstacles《长的有倒刺带状障碍物的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1910-1998(2003) Standard Specification for Long Barbed Tape Obstacles《长的有倒刺带状障碍物的标准规范》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 1910 98 (Reapproved 2003)Standard Specification forLong Barbed Tape Obstacles1This standard is issued under the fixed designation F 1910; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n
2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers barbed tape materials andconfigurations used for security barriers.2. Referenced Documents2.1 ASTM Standards:
3、A 176 Specification for Stainless and Heat-Resisting Chro-mium Steel Plate, Sheet and Strip2A 240 Specification for Chromium and Chromium-NickelStainless Steel Plate, Sheet and Strip for Pressure Vesselsand for General Applications2A 370 Test Methods and Definitions for Mechanical Testingof Steel Pr
4、oducts2A 666 Specification for Annealed or Cold-Worked Austen-itic Stainless Steel Sheet, Strip, Plate and Flat Bar2A 764 Specification for Metallic Coated Carbon Steel Wire,Coated at Size and Drawn to Size for Mechanical Springs2F 1379 Terminology Relating to Barbed Tape33. Terminology3.1 Refer to
5、Terminology F 1379.4. Classification4.1 Refer to 5.1.8.5. Ordering/Specifying Information5.1 Ordering or specifying barbed tape shall include thefollowing information as per sample specification, or byreferencing item numbers in Tables 1 and 2 (indicate number ofloops, if applicable). Material furni
6、shed under this specificationshall conform to applicable requirements of current editions ofASTM Standards.NOTE 1The following sample specification is provided to assist whenspecifying or ordering barbed tape material. Actual size and style will varyby individual job requirements.Sample Specificatio
7、n OnlyBarbed tape obstacle shall be 30 in.diameter (62 in.). Each loop shall consist of 24 (61) clusters of fourneedle-sharp barbs on 4 in. centers, each barb measuring a minimum of1.2 in. in length. The barbed tape shall be fabricated from Series 430stainless steel with optional hardness. The barbe
8、d tape shall be perma-nently coldclenched over an austenitic mechanical spring core wire. Thewire shall have a diameter of 0.098 in. with a minimum tensile strength ofapproximately 140 psi. The barbed tape shall have a minimum 230 wrapabout the core wire. Adjacent alternate loops shall be clipped to
9、gether infive (5) locations around the circumference to obtain the concertina effect.Clip spacing of the extended coil shall be 12 6 2 in. Clips shall be capableof withstanding a minimum pull load of 200 lb. Each coil shall contain 51loops and cover 25 6 1 ft.5.1.1 QuantityThe number of units of bar
10、bed tape re-quired. For fixed length units, the length per unit should bespecified.5.1.2 Description Barbed tape shall be described as singlecoil helical, single coil concertina, double coil concertina, ordouble coil helical.5.1.3 DiameterThe purchaser shall specify the packageddiameter. When double
11、 coil products are specified, the innerand outer coil packaged diameters shall be given.5.1.4 Barb Length Refer to Terminology F 1379 andTables 1 and 2.5.1.5 Coil LoopsThe number of coil loops shall bespecified by the purchaser.5.1.6 Unit Length The purchaser shall specify the in-stalled length and
12、coil spacing, including the coil spacingtolerance.5.1.7 Number of attachment points, in accordance withTerminology F 1739 and Tables 1 and 2.5.1.8 Cross Sections The purchaser shall specify the crosssections in accordance with Terminology F 1379.6. Material6.1 Composition Barbed tape shall be manufa
13、ctured fromstainless and galvanized steel in accordance with the ASTMstandards listed in Section 2. Manufacturers are not necessarilylimited to those materials listed.6.1.1 Stainless Steel Stainless steel strip shall be eitherferretic or austenitic. Stainless steel should be ordered to theAISA or UN
14、S designations to ensure the correct chemistry.6.1.1.1 Ferritic stainless steels shall be produced in accor-dance with Specification A 176 or Specification A 240.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Ch
15、ain Link Fence andWire Accessories.Current edition approved July 10, 2003. Published September 2003. Originallyapproved in 1998. Last previous edition approved in 1998 as F 1910 - 98.2Annual Book of ASTM Standards, Vol 01.03.3Annual Book of ASTM Standards, Vol 01.06.1Copyright ASTM International, 10
16、0 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.1.1.2 Austenitic stainless steels shall be purchased inaccordance with Specification A 666.7. Dimensions and Permissible Variations7.1 Permissible variations within coil diameters shall be asspecified in Tables 1 and
17、 2 for standard trade sizes.8. Workmanship, Finish and Appearance8.1 Workmanship Coil loops shall not be kinked, unless itis part of the design.8.1.1 Each coil shall be one continuous length properlycoiled and firmly tied for shipping. Welds made in the stripprior to forming are permitted. A maximum
18、 of three splices percoil are permitted either by overlapping and welding orpermanently clamping together with a suitable device designedfor the purpose.8.2 Surfaces shall be smooth and free of rust with no seriousdefects, such as pits, die marks, and other defects to impair theintegrity of the prod
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF191019982003STANDARDSPECIFICATIONFORLONGBARBEDTAPEOBSTACLES 倒刺 带状 障碍物 标准规范 PDF

链接地址:http://www.mydoc123.com/p-536008.html