1、BS EN ISO 13143-2:2016Electronic fee collection Evaluation of on-board and roadside equipment for conformity to EN ISO/TS12813Part 2: Abstract test suite (ISO 13143-2:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 13143-2:2016 BRITISH STANDARDNational
2、 forewordThis British Standard is the UK implementation of EN ISO 13143-2:2016. It supersedes DD CEN ISO/TS 13143-2:2011 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee EPL/278, Intelligent transport systems.A list of organizations represented on this
3、 committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 89358 2 ICS
4、 03.220.20; 35.240.60 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate Text affectedEUROPEAN S
5、TANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13143-2 December 2016 ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 13143-2:2011English Version Electronic fee collection - Evaluation of on-board and roadside equipment for conformity to EN ISO/TS 12813 - Part 2: Abstract test suite (ISO 13143-2:2016)
6、 Perception du tlpage - valuation des quipements embarqus et en bord de route quant la conformit avec lISO 12813 - Partie 2: Suite dessais abstraite (ISO 13143-2:2016) Elektronische Gebhrenerhebung - Konformittsbeurteilung von bordeigenen und straenseitigen Ausrstungen nach ISO/TS 12813 - Teil 2: Zu
7、sammengefasstes Prfprogramm (ISO 13143-2:2016) This European Standard was approved by CEN on 6 December 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter
8、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made
9、 by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni
10、a, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDAR
11、DIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13143-2:2016 EBS EN ISO 13143-2:2016EN
12、 ISO 13143-2:2016 (E) 3 European foreword This document (EN ISO 13143-2:2016) has been prepared by Technical Committee ISO/TC 204 “Intelligent transport systems” in collaboration with Technical Committee CEN/TC 278 “Intelligent transport systems” the secretariat of which is held by NEN. This Europea
13、n Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be withdrawn at the latest by June 2017. Attention is drawn to the possibility that some of the elements of
14、this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN ISO/TS 13143-2:2011. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the followin
15、g countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw
16、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13143-2:2016 has been approved by CEN as EN ISO 13143-2:2016 without any modification. BS EN ISO 13143-2:2016ISO 13143-2:2016(E)Foreword ivIntroduction v1
17、Scope . 12 Normative references 13 Terms and definitions . 14 Abbreviated terms 25 Abstract test method (ATM) 35.1 General . 35.2 Test architecture 36 Untestable test purposes (TPs) . 37 Abstract test suite (ATS) conventions . 47.1 General . 47.2 Naming conventions . 47.2.1 Declarations part . 47.2.
18、2 Constraints part 57.2.3 Dynamic part . 67.3 Implementation conventions 77.3.1 Declaration part 77.3.2 Constraint part 77.3.3 Dynamic part . 7Annex A (normative) Abstract test suite (ATS) for on-board equipment (OBE) . 8Annex B (normative) Abstract test suite (ATS) for roadside equipment (RSE) . 9A
19、nnex C (normative) PIXIT proforma for on-board equipment (OBE) .10Annex D (normative) PIXIT proforma for roadside equipment (RSE) .12Bibliography .14 ISO 2016 All rights reserved iiiContents PageBS EN ISO 13143-2:2016ISO 13143-2:2016(E)ForewordISO (the International Organization for Standardization)
20、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre
21、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to devel
22、op this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/
23、IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during th
24、e development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning o
25、f ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this documen
26、t is ISO/TC 204, Intelligent transport systems.This first edition of ISO 13143-2 cancels and replaces ISO/TS 13143-2:2011, which has been technically revised and incorporates the following main modifications compared to ISO/TS 13143-2: conversion from a Technical Specification to an International St
27、andard; amendment of terms, in order to reflect harmonization of terms across electronic fee collection (EFC) standards; amendments to reflect changes in ISO 13143-1 due to changes to the underlying standards, in particular ISO 12813; editorial and formal corrections.A list of all parts in the ISO 1
28、3143 series can be found on the ISO website.iv ISO 2016 All rights reservedBS EN ISO 13143-2:2016ISO 13143-2:2016(E)IntroductionISO 17575 is part of a set of standards that supports interoperability of autonomous EFC systems. It defines the EFC context data, their charge reports and their use of com
29、munication infrastructure.The set of standards also supports short-range communication links in the context of autonomous electronic fee collection (EFC) on-board equipment (OBE) to enable spot checks for the enforcement process. The application interface is defined in ISO 12813:2015.Within the set
30、of EFC standards, this document defines the process and tests for conformity evaluation of OBE and roadside equipment (RSE) that comply with the requirements in ISO 12813:2015.This document is intended to assess OBU and RSE capabilities, assess OBU and RSE behaviour, serve as a guide for OBU and RSE
31、 conformance evaluation and type approval, achieve comparability between the results of the corresponding tests applied in different places at different times, and facilitate communication between parties.This document is based on ISO 12813:2015, the set of dedicated short-range communication (DSRC)
32、 standards defining the communication stack, and ISO/IEC 9646.This document is based on using the tree and tabular combined notation (TTCN) that is a standardized language suitable for specification of test cases and steps for assessment of protocol and application behaviour. The TTCN language is al
33、so supported by modern automated tools that accelerate software design, implementation and testing. ISO 2016 All rights reserved vBS EN ISO 13143-2:2016BS EN ISO 13143-2:2016Electronic fee collection Evaluation of on-board and roadside equipment for conformity to ISO 12813 Part 2: Abstract test suit
34、e1 ScopeThis document specifies the abstract test suite (ATS) to evaluate the conformity of on-board equipment (OBE) and roadside equipment (RSE) to ISO 12813 in accordance with the test suite structure and test purposes defined in ISO 13143-1:2016.It provides a basis for conformance tests for dedic
35、ated short-range communication (DSRC) equipment (OBE and RSE) to enable interoperability between equipment supplied by different manufacturers.In order to ascertain that OBE and RSE fulfil essential radio requirements, they are also likely to be subject to additional factory, site and system accepta
36、nce testing (e.g. of physical and environmental endurance, quality assurance and control at manufacturing, and charge point integration), which is outside the scope of this document.NOTE For example, within the European market, the essential radio requirements are set out in European Directives, com
37、pliance with which is a prerequisite for CE marking and placing on the European market.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited app
38、lies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO/IEC 9646-3:1998, Information technology Open Systems Interconnection Conformance testing methodology and framework Part 3: The Tree and Tabular Combined Notation (TTCN)ETSI/TS 102 486-2
39、-3 V1.2.1:2008-10, Electromagnetic compatibility and Radio spectrum Matters (ERM); Road Transport and Traffic Telematics (RTTT); Test specifications for Dedicated Short Range Communication (DSRC) transmission equipment; Part 2: DSRC application layer; Sub-Part 3: Abstract Test Suite (ATS) and partia
40、l PIXIT proforma3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing plat
41、form: available at http:/www.iso.org/obp3.1base standardapproved international standard, technical specification or ITU-T RecommendationNote 1 to entry: This includes but is not limited to approved standard deliverables from ISO, ITU, CEN, CENELEC, ETSI and IEEE.INTERNATIONAL STANDARD ISO 13143-2:20
42、16(E) ISO 2016 All rights reserved 1BS EN ISO 13143-2:2016ISO 13143-2:2016(E)SOURCE: ISO/IEC/TR 10000-1:1998, 3.1.13.2implementation conformance statementstatement of capabilities and options that have been implemented defining to what extent the implementation is compliant with a given specificatio
43、nSOURCE: ISO/TS 14907-2:2016, 3.6, modified3.3implementation conformance statement proformadocument, in the form of a questionnaire, which when completed for an implementation or a system becomes an implementation conformance statement (ICS)SOURCE: ISO/IEC 9646-1:1994, 3.3.403.4implementation extra
44、information for testingstatement containing all of the information related to the implementation under test (IUT) and its corresponding system under test (SUT) which will enable the testing laboratory to run an appropriate test suite against that IUTSOURCE: ISO/TS 14907-2:2016, 3.83.5implementation
45、extra information for testing proformadocument, in the form of a questionnaire, which when completed for an implementation under test (IUT) becomes an implementation extra information for testing (IXIT)SOURCE: ISO/IEC 9646-1:1994, 3.3.42, modified3.6on-board equipmentall required equipment on-board
46、a vehicle for performing required EFC functions and communication services3.7on-board unitsingle electronic unit on-board a vehicle for performing specific EFC functions and for communication with external systems3.8roadside equipmentequipment located along the road, either fixed or mobile3.9testerc
47、ombination of equipment, humans and processes able to perform specified conformance testsSOURCE: EN 15876-1:2016, 3.124 Abbreviated termsAP Application Process (ISO 14906)ASN.1 Abstract Syntax Notation One (ISO/IEC 8824-1)ATS Abstract Test SuiteBI Behaviour Invalid (i.e. Invalid Behaviour tests)2 IS
48、O 2016 All rights reservedBS EN ISO 13143-2:2016ISO 13143-2:2016(E)BV Behaviour Valid (i.e. Valid Behaviour tests)Cf Confirm (ISO 14906)CM Coordination messageDSRC Dedicated Short-Range Communication (ISO 14906)DUT Device Under Test (ISO/TS 14907-2)EFC Electronic Fee Collection (ISO 17573)ICS Implem
49、entation Conformance Statement (EN 15509)IXIT Implementation eXtra Information for Testing (ISO/TS 14907-2)IUT Implementation Under Test (ISO/TS 14907-2)MAC Medium Access Control (EN 12795)OBE On-board equipmentOBU On-board unitPIXIT Protocol Implementation eXtra Information for TestingRSE Roadside equipmentSAP Service Access PointSCS Semiconductor Characterization SystemTC Test CaseTSS Test Suite Structure (EN 15876-1)5 Abstract test method (ATM)5.1 GeneralThis clause describes the abstract test method (ATM)
