1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improvethis document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box3990, Columbus, OH 43213-1199, or telephone (614) 692-0562, or facsimile (FAX) (614) 69
2、3-1644.AMSC N/A FSC 5915DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-55171CSeptember 17, 2001SUPERSEDINGA-A-55171BSeptember 27, 1995COMMERCIAL ITEM DESCRIPTIONFILTER, RADIO FREQUENCY INTERFERENCEThe General Services Administration has authorized the
3、use of thiscommercial item description (CID) for all federal agencies as areplacement for Federal Specification W-F-2190/11.1. SCOPE. This CID covers the general requirements for radio frequency interference (RFI) suppression power linefilters. These filters consist of capacitors and inductors used
4、in combination with each other and are provided withresistors as a safety feature. This series of RFI filters incorporate the special International ElectrotechnicalCommission (IEC) power line connector. Filters covered by this CID are intended for commercial/industrialapplications and should not be
5、used in military systems needing stringent environmental and electrical requirements.2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number(PIN) as shown in the following example (see 7.1).AA55171 -01CID number Dash number3. SALIENT CHARACTERISTI
6、CS.3.1 Interface and physical dimensions. Filters supplied to this CID shall be as specified herein (see figures 1 and 2).3.2. Voltage rating. The voltage rating shall be 120 V ac at 60 Hz; 250 V ac at 50 Hz.3.3 Operating frequency. The operating frequency shall be 50/60 Hz.3.4 Current rating. The c
7、urrent rating shall be as specified in table I.3.5 Operating ambient temperature range. The operating ambient temperature range shall be -10G01C to +40G01C atrated current.3.6 Maximum leakage current, line-to-ground. The maximum leakage current, line-to-ground, shall be 0.25 mA at120 V ac, 60 Hz; .5
8、0 mA at 250 V ac, 50 Hz.3.7 Hipot rating (1 minute). The hipot rating shall be 2,250 V dc line-to-ground; 1,450 V dc line-to-line.3.8 Insertion loss. Insertion loss is given for line-to-ground in a 50-ohm circuit. Values shall be as specified in table I.3.9 Electrical schematic. The electrical schem
9、atic shall be as specified on figure 2.3.10 Marking. Filters supplied to this CID shall be marked with the manufacturers (MFRs) standard commercialPIN.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55171C2Case style 1Case style 2FIGURE 1. Case c
10、onfigurations and dimensions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55171C3A(max)B(max)C(max)DG02.015/G02.38E(max)F(max)PINAA55171-Inch mm Inch mm Inch mm Inch mm Inch mm inch mm01 2.20 55.9 1.19 30.2 .81 20.6 1.575 40.01 1.98 50.3 - -02
11、 2.20 55.9 1.19 30.2 .81 20.6 1.575 40.01 1.98 50.3 - -03 2.20 55.9 1.19 30.2 .81 20.6 1.575 40.01 1.98 50.3 - -04 2.62 66.5 1.19 30.2 .81 20.6 1.575 40.01 1.98 50.3 - -05 2.62 66.5 1.19 30.2 .81 20.6 1.575 40.01 1.98 50.3 - -06 1.55 39.4 1.19 30.2 .85 21.6 1.575 40.01 1.98 50.3 .65 16.507 1.55 39.4
12、 1.19 30.2 .85 21.6 1.575 40.01 1.98 50.3 .65 16.508 1.55 39.4 1.19 30.2 .85 21.6 1.575 40.01 1.98 50.3 .65 16.5NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. Fastons: (Two) .250 inch (6.35 mm).Holes: .07 inch (1.8 mm) diameter.4. Mounting slots: (T
13、wo) .132 inch (3.35 mm) diameter.5. Ground fastons: .07 inch (1.8 mm) x .155 inch (3.94 mm) slot.6. Metric equivalents are in parentheses.FIGURE 1. Case configuration and dimensions - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5517
14、1C4TABLE I. Current rating and insertion loss.Minimum insertion loss (dB)Line-to-ground in 50 -ohm circuitFrequency (MHz)PINAA55171-Current rating Casestyle.15.5 1 5 103001 1 A 1 22 35 40 46 50 4902 3 A 1 15 25 30 45 50 5403 6 A 1 9202541455004 10 A 1 8152034394405 1/ 10 A 1 8152034394406 1 A 2 22 3
15、5 40 46 50 4907 3 A 2 15 25 30 45 50 5408 6 A 2 920254145501/ AA55171-05 employs schematic B.Schematic BFIGURE 2. Electrical schematics.Schematic AProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55171C54. REGULATORY REQUIREMENTS. The offeror/cont
16、ractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).5. PRODUCT CONFORMANCE PROVISIONS5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, confor
17、m to theproducers own drawings, specifications, standards, and quality assurance practices, and be the same productoffered for sale in the commercial market. The Government reserves the right to require proof of such conformance.6. PACKAGING. Preservation, packing, and marking shall be as specified
18、in the contract or order.7. NOTES.7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2for PIN format example.7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and submission ofthese filters to DSCC und
19、er the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code58536 should be used.7.3 Source of documents. This section is not applicable to this CID.7.4 Ordering data. The contract or order should specify the following:a. CID document number, revision, and CID PIN.b. Product co
20、nformance provisions.c. Packaging requirements.7.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with thefollowing manufacturers of commercial products. At the time of CID preparation and coordination, thesemanufacturers were known to have commerci
21、al products that would meet the requirements of this CID. (NOTE:This information should not be considered as a list of approved manufacturers or be used to restrict procurement toonly the manufacturers shown.)MFRs CAGE MFRs name and address0S2B1 RME Filters, IncorporatedP. O. Box 83898 Route 101 AAm
22、herst, NH 03031-083805245 CORCOM, Incorporated844 East Rockland RoadLibertyville, IL 60048Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55171C67.6 Part number (PIN) supersession data. This CID supersedes the following manufacturers PINs as show
23、n. Thisinformation is being provided to assist in reducing proliferation in the government inventory system.TABLE II. PIN supersession data.MFRs CAGE0S2B1MFRs CAGE05245PINAA55171- MFRs Commercial PIN 1/01 RME-AC-101 1EF1F02 RME-AC-103 3EF1F03 RME-AC-106 6EF1F04 RME-AC-110 10EF1F05 RME-AC-110-1 10EF1
24、FC06 RME-AC-201 1EF2F07 RME-AC-203 3EF2F08 RME-AC-206 6EF2F1/ The manufacturers PIN shall not be used for procurement to the requirementsof this CID. At the time of preparation of this CID, the aforementioned commercialproducts were reviewed and could be replaced by the CID PIN shown. For actualpart
25、 marking requirements, see 3.11.7.7 Government users. To acquire information on obtaining these filters from the Government inventory system,contact Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000,telephone (614) 692-0562 or facsimile (614) 693-1644.7.7.
26、1 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID. The listis for information only and may not be indicative of all possible NSNs associated with the CID. For up to dateinformation on assigned NSNs, please contact the aforementioned DSCC office (See 7.7).MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA - 7FXECustodians:Navy - EC Preparing Activity:DLA-CCProject 5915-0409Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
