1、 Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to FluidFlowdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSI
2、ST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 4720 A-A-55697B 22 February 2012 SUPERSEDING A-A-55697A 9 October 2002 COMMERCIAL ITEM DESCRIPTION TUBE, NONMETALLIC; POLYVINYL CHLORIDE (PVC) FLEXIBLE (FOR LABORATORY AND MEDICAL USE) The General Services Administration has authorized t
3、he use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for clear flexible PVC tubing. Clear flexible PVC tubing covered by this CID is intended for commercial/industrial applications in medical and laborat
4、ory application, including fluid signals, low pressure air, gas, and vacuum but not limited to medical transfusions and infusions. 2. CLASSIFICATION/PART OR IDENTIFICATON NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1). 2.1
5、 Sizes. Plastic tubing should be of the nominal inside diameter (ID), outside diameter (OD) and wall thickness, as specified in table I. AA 55697 X X X Form (see table III) Length (see table II) Size code (see table I) Basic CID identifier (number) Document identifier (CID) INCH-POUND Provided by IH
6、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55697B 2 TABLE I. Inside/outside diameter and wall thickness of tubes. 1/ 2/ 3/ Size code Nominal ID 4/OD nominal WT 5/(inches) (mm) (inches) (mm) (inches) (mm) 01 0.125 (3.2) 0.1875 (4.8) 0.0313 (0.8) 02 0.1563
7、(4.0) 0.2813 (7.1) 0.0625 (1.6) 03 0.1875 (4.8) 0.3125 (7.9) 0.0625 (1.6) 04 0.2500 (6.4) 0.3750 (9.5) 0.0625 (1.6) 05 0.3125 (7.9) 0.4375 (10.5) 0.0625 (1.6) 06 0.3750 (9.5) 0.5000 (12.7) 0.0625 (1.6) 07 0.3750 (9.5) 0.6250 (15.9) 0.1250 (3.2) 08 0.5000 (12.7) 0.7500 (19.1) 0.1250 (3.2) 09 1.0000 (
8、25.4) 2.0000 (50.8) 0.5000 (12.7) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. 3/ Sizes other than those shown in table I may be ordered by specifying dimensional data in lieu of PIN (see 7.1). 4/ Tolerance on inside diameter for all sizes shall be .0156 inch (0
9、.4 mm). 5/ Tolerance on wall thickness for all sizes shall be - 0 or +.0156 inch (-0.00 or +0.4 mm). 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Tubing supplied to this CID shall be as specified herein. 3.2 Material. Tubing provided in accordance with this CID shall be colorle
10、ss, clear, and flexible PVC. 3.3 Dimensioning. The values stated in inch-pound units are to be regarded as the standard. The metric values stated in parentheses throughout this CID are for informational purposes only and have been rounded to only one decimal place for convenience. 3.4 Lengths. Tubin
11、g shall be furnished in the length specified in table II (see 7.5c). TABLE II. Tubing lengths. 1/ 2/Length code Length A 50 Feet 15.24 meters B 100 Feet 30.48 meters C 250 Feet 76.20 meters D 500 Feet 152.40 meters E 1000 Feet 304.80 meters 1/ Dimensions are in inches. 2/ Metric equivalents are give
12、n for information only. 3.5 Form. Tubing shall be furnished in the form specified in table III (see 7.5c). TABLE III. Tubing forms. Form code Form 1 Coils 2 Reels 3 Straight Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55697B 3 3.6 Flexibility
13、. Tubing shall be capable of bending around a mandrel equal to five times the OD of the tube without collapsing or restricting flow. 3.7 Physical properties. Physical properties of the tubing shall be as specified in table IV when tested in accordance with the test method shown. TABLE IV. Physical p
14、roperties. Property Requirement Test method Brittleness temperature -50.8F (-46C) ASTM D746 Specific gravity 1.15 - 1.80 ASTM D792 Tensile strength, psi 1800 - 2100 ASTM D638 Elongation, percent 300 minimum ASTM D638 3.8 Chemical resistance. Tubing shall not discolor, flake, crack or pit when tested
15、 in accordance with USP-NF, Physicochemical Tests-Plastics, ASTM D1003, Standard Method of Test for Haze and Luminous Transmittance of Transparent Plastics, and ASTM E308, Standard Practice for Computing the Colors of Objects by Using the CIE System. 3.9 Sterilization. Tubing shall be capable of wit
16、hstanding sterilization by steam, ethylene oxide, radiation, or other method that meets the requirements of the USP-NF, Sterility Tests for Transfusion and Infusion Assemblies and Similar Medical Devices. 3.10. Heat resistance. Tubing shall be capable of withstanding temperatures of 2005 F (93.32.8
17、C) for one hour without visual signs of deterioration such as discoloring, flaking, cracking, pitting, hardening, or melting. 3.11 Biological reactivity. Tubing shall meet the requirements of USP Class II plastics and the Association for the Advancement of Medical Instrumentation, AAMI/ANSI 10993-1.
18、 3.12 Metal content. The use of hazardous materials (see 7.2) shall be eliminated or minimized where possible. Tubes shall not contain more than five parts per million (ppm) of heavy metals, such as lead, in their ash residue when tested as follows: a. Two sample tubes shall be selected at random fr
19、om each lot (lot is defined as a continuous run of tubing from the same batch or raw material, and offered for delivery under one contract). b. From each sample accurately weigh a 0.176 oz. (5 gm) sample into one-ounce VYCOR crucibles. c. Reduce to ash in a muffle furnace at 1202F (650C) for 8 hours
20、. d. Let cool to room temperature and add 0.507 fluid ounces (15 ml) of 1:1 hydrochloric acid. e. Bring to a boil on a hot plate, allow to boil for two to three minutes, remove, let cool and filter through Whatman grade #2 filter paper (particle retention 8m) into a 1.691 fluid ounces (50 ml) volume
21、tric flask. f. Rinse the residue from the filter with deionized water and dilute to 1.691 fluid ounces (50 ml). g. Prepare standard lead solutions of one, two, and five ppm lead. h. Determine the absorbencies of these solutions at the 283 millimicron wavelength using a Hollow Cathode Pb lamp and 10x
22、 scale expansion on an atomic absorption spectrophotometer. i. Determine the absorbance of the sample solutions using the same conditions as with the standards. j. The calculated factors of the three standards are averaged to give ppm/unit A. Provided by IHSNot for ResaleNo reproduction or networkin
23、g permitted without license from IHS-,-,-A-A-55697B 4 Calculation: Lead content in ppm = AFDilutionWA = Absorbance F = Factor = (concentration standard in ppm Pb)absorbanceW = Sample weight in grams 3.13 Marking. Tubing supplied to this CID shall be marked with the manufacturers (MFRs) standard comm
24、ercial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.14 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds
25、the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.15 Workmanship. Tubing shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQ
26、UIREMENTS. The offer/contractor is encouraged to use recovered material to the maximum extent practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics o
27、f this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking s
28、hall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum e
29、xtent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals is available on their website at http:/www.epa.gov/epawaste/hazard/wastemin/in
30、dex.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein (see section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purpos
31、es, inventory control, and submission of this tubing to DLA Land and maritime under the Parts Management Advisory Team (PMAT) evaluation program, CAGE code 58536 should be used. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55697B 5 7.4 Source
32、of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Regulations (FAR) (The online document is available at https:/www.acquisition.gov/far/ or copies of the document are available at the U.S. Government Bookstore, 710 North Capital Street N.W., Washington D.C 20401-0001 or online at http:/boo
33、kstore.gpo.gov/). Other publications ASSOCIATION FOR THE ADVANCEMENT OF MEDICAL INSTRUMENTATION (AAMI) AAMI/ANSI 10993-1 - Biological Evaluation of Medical Devices (Copies of documents are available online at http:/www.aami.org/ or from Association for the Advancement of Medical Instrumentation, 430
34、1 N. Fairfax Drive, Suite 301, Arlington, VA 22203-1633.) ASTM INTERNATIONAL ASTM D638 - Standard Test Method for Tensile Properties of Plastics ASTM D746 - Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D792 - Standard Test Methods for Density and Specifi
35、c Gravity (Relative Density) of Plastics by Displacement ASTM D1003 - Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics ASTM D3951 - Standard Practice for Commercial Packaging ASTM E308 - Standard Practice for Computing the Colors of Objects by Using the CIE System (Co
36、pies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) UNITED STATES PHARMACOPEIA (USP) USP-NF - Physicochemical Tests-Plastics USP-NF - Sterility Tests for Transfusion and Infusion A
37、ssemblies and Similar Medical Devices (Copies of documents are available online at http:/www.usp.org or from U. S. Pharmacopei, 12601 Twinbrook Parkway, Rockville, Maryland 20852-1790.) 7.5 Ordering data. The contract or order should specify the following: a. Title, number, and date of the CID. b. S
38、ize code and wall thickness (see table I). c. Length (see table II, 3.4) and form (see table III, 3.5) required. d. Applicable level of preservation, packaging, and packing (see 6). e. Applicable marking (see 3.13). f. Quantity of tubing required. Provided by IHSNot for ResaleNo reproduction or netw
39、orking permitted without license from IHS-,-,-A-A-55697B 6 7.6 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following manufacturers of commercial products. At the time of CID preparation and coordination, these manufacturers were known to
40、 have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFRs CAGE MFRs name and address 1L0C5 Harrison Hose and Tubing Inc. 2705 K
41、USER RD Trenton, NJ 08691 Voice Telephone: 866-333-3350 Fax 609-631-8796 http:/ 1V630 F and R Sales Inc. 109 Gauntt St PO Box 189 Burlington, NJ 08016-1938 Telephone: 609-423-9033 0AMA0 Dynamation Research Inc. 2301 Pontius Ave Los Angeles, CA 90064-1809 Telephone: 310-477-1224 Fax: 310-479-5656 htt
42、p:/ 15761 Fournier Rubber and Supply Co. 1341 Norton Ave. PO Box 548 Columbus, OH 43212-3158 Telephone: 614-294-6453 Fax: 614-294-0644 http:/ 7.7 Part number (P/N) supersession data. These CID part numbers supersede the following MFRs P/Ns as shown. This information is being provided to assist in re
43、ducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55697B 7 TABLE V. P/N supersession data. Dash number (see table I,II, & III) A-A-55697 MFRs CAGE MFRs P/N 1/Dash number (see table I,II, & II
44、I) A-A-55697 MFRs CAGE MFRs P/N 1/01A1 1L0C5 10-01A1 06B2 1L0C5 10-06B2 02A1 1L0C5 10-02A1 07B2 1L0C5 10-07B2 03A1 1L0C5 10-03A1 08B2 1L0C5 10-08B2 04A1 1L0C5 10-04A1 09B2 1L0C5 10-09B2 05A1 1L0C5 10-05A1 01B3 1L0C5 10-01B3 06A1 1L0C5 10-06A1 02B3 1L0C5 10-02B3 07A1 1L0C5 10-07A1 03B3 1L0C5 10-03B3
45、08A1 1L0C5 10-08A1 04B3 1L0C5 10-04B3 09A1 1L0C5 10-09A1 05B3 1L0C5 10-05B3 01A2 1L0C5 10-01A2 06B3 1L0C5 10-06B3 02A2 1L0C5 10-02A2 07B3 1L0C5 10-07B3 03A2 1L0C5 10-03A2 08B3 1L0C5 10-08B3 04A2 1L0C5 10-04A2 09B3 1L0C5 10-09B3 05A2 1L0C5 10-05A2 01C1 1L0C5 10-01C1 06A2 1L0C5 10-06A2 02C1 1L0C5 10-0
46、2C1 07A2 1L0C5 10-07A2 03C1 1L0C5 10-03C1 08A2 1L0C5 10-08A2 04C1 1L0C5 10-04C1 09A2 1L0C5 10-09A2 05C1 1L0C5 10-05C1 01A3 1L0C5 10-01A3 06C1 1L0C5 10-06C1 02A3 1L0C5 10-02A3 07C1 1L0C5 10-07C1 03A3 1L0C5 10-03A3 08C1 1L0C5 10-08C1 04A3 1L0C5 10-04A3 09C1 1L0C5 10-09C1 05A3 1L0C5 10-05A3 01C2 1L0C5
47、10-01C2 06A3 1L0C5 10-06A3 02C2 1L0C5 10-02C2 07A3 1L0C5 10-07A3 03C2 1L0C5 10-03C2 08A3 1L0C5 10-08A3 04C2 1L0C5 10-04C2 09A3 1L0C5 10-09A3 05C2 1L0C5 10-05C2 01B1 1L0C5 10-01B1 06C2 1L0C5 10-06C2 02B1 1L0C5 10-02B1 07C2 1L0C5 10-07C2 03B1 1L0C5 10-03B1 08C2 1L0C5 10-08C2 04B1 1L0C5 10-04B1 09C2 1L
48、0C5 10-09C2 05B1 1L0C5 10-05B1 01C3 1L0C5 10-01C3 06B1 1L0C5 10-06B1 02C3 1L0C5 10-02C3 07B1 1L0C5 10-07B1 03C3 1L0C5 10-03C3 08B1 1L0C5 10-08B1 04C3 1L0C5 10-04C3 09B1 1L0C5 10-09B1 05C3 1L0C5 10-05C3 01B2 1L0C5 10-01B2 06C3 1L0C5 10-06C3 02B2 1L0C5 10-02B2 07C3 1L0C5 10-07C3 03B2 1L0C5 10-03B2 08C
49、3 1L0C5 10-08C3 04B2 1L0C5 10-04B2 09C3 1L0C5 10-09C3 05B2 1L0C5 10-05B2 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part m
