1、k AN105701 THRU AN105800 REV 4 53 7777715 00002b7 2 F D. SUP CLASS 5306 %=AL IDEWIFICATION PER . i88 CSRIK WH ENDS 2 HOLES ON AXIS OF ANCIUIM MCATIOR 60. TO .loo DIA - THD WITJIII .005. THIS SIRPACE HUST BB SQUARE WITH s“K WITHIN -003 IDICATm READIO - 150J . O90 L - .625 .688 :E : 3 1. OGO 1.062 1.1
2、29 1. ltl 1.250 1.312 1 375 1.438 1.500 1.562 1.625 1.688 1 * 750 - A - -515 .578 .640 .TO2 .765 . a28 .ego 952 1.015 1.078 1.140 1.202 1.265 1.328 1.390 1.42 1.515 1.578 1.640 - - II +.o00 -.o60 - (a) .125 . i88 .250 .312 .375 .438 .500 .562 .625 .688 a750 .e12 .E75 .938 1.000 1.062 I3 - PART 10. A
3、N105706 As:;:FI AN105709 AN105710 AN105711 AN105712 AN10571 AN105713 AN105715 AN105716 AN105717 AN105718 AN105719 AN105720 AN105721 AN105722 AN105723 AN105724 CBAKlrER 30 TO .500 DU (OPPOSITE SIDE OPIIOIUL) - L - 1 875 2.000 2.125 2.250 2-375 2.500 2.625 2.750 2 - 875 3.000 3.125 3.250 3.375 3.500 3
4、625 3 - 750 3.875 4.000 4.125 4.250 4.375 K PART HO. A +. O00 -.O60 1 188 AN105725 1: 12 AN105726 2.015 1 .f38 AN105727 2.140 1.562 AN105728 2.390 1.812 AN105730 2.515 1.938 AN105731 2.640 2.062 AN105732 2.765 2.188 AN105733 2.890 2. 10 AN105734 3.015 2.338 AN105735 3.265 2.688 AN10573 3.390 2.812
5、AN10573g 3.515 2.938 AN105739 3.640 )A62 AN105740 3.765 3.188 AN105741 3.890 3.312 AN105742 4.015 3.438 AN105743 4.140 3.562 ANiQ5744 4.265 3.688 AN105745 2.265 1.688 105729 3.140 2.562 A105736 (a) THREAD TO HEAD. MAXIMUM TU0 IMPERFECT THREADS. OF THIS 53OU-S A UNIT MAY VARY FREELY NOTE: (i) SHANK S
6、HALL BE STRAIGHT WITHIN .O03 FIR. PER INCH OF BOLT LENGTH. (2) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE UITHIN .O06 FIR (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE UASHER FACE DIAHETER AND HEXAGON SHALL BE WITHIN .O15 FIR. INACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SU
7、PERSEDING STANDARD. HATERIAL: CORROSION RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 MANUFACTURING SPECIFICATIOS: AMS 7472 BREAK SHARP EDCES .003-.O15 UNLESS OTHERVISE SPECIFIED. DIUENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS f.010, ANGU
8、LAR DO NOT USE UNASSIGNED PART NUHBERS. ) INSPECTION: ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTlON IN ACCORDANCE UITH AMS2645. DIHENSIONS f2. THIS STANDARD WAS DEVELOPED COOPERATIVELY UITH THE ENGINE AND PROPELLER UTILITY PARTS COMHITTEE OF THE SAE. AIR FORCE-NAW AERONAUTICAL STANDARD AN I 0570 I P.A. USAF - Il D c lier Cu 5 t TMWI I ANIOS800 BOLT - CRES HEX HEAD, DRILLED SHANK, .3125-24 I Navy - AS Army - AV 1 THIS DOCUMENT CONTAINS -I- . PAGES. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
