1、AMSC N/A FSC 4730 AN795 Rev 5 4 August 2011 SUPERSEDING AN795 Rev 4 20 August 1956 DETAIL SPECIFICATION SHEET TEE, UNION This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of t
2、his specification sheet and MIL-DTL-6001. FIGURE 1. Tee, union. INCH-POUND Inactive for new design after 24 July 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dash numbers and size. 1/ 2/ Dash number Tubing outside diameter Thread T
3、AND10089 B +.047 -.000 C +.047 -.000 E +.047 -.000 R .015 Rad W .015 Brass Corrosion resistant steel 2 C2 .125 .3125-32 UNEF-3A .625 .625 .625 .062 .312 3 C3 .188 .3750-24 UNF-3A .688 .688 .688 .375 4 C4 .250 .4375-20 UNF-3A .750 .750 .750 .094 .435 5 C5 .312 .5000-20 UNF-3A .875 .875 .875 6 C6 .375
4、 .6250-18 UNF-3A 1.000 1.000 1.000 .125 .625 8 C8 .500 .7500-16 UNF-3A 1.188 1.188 1.188 .750 10 C10 .625 .9375-14 NS-3 1.250 1.250 1.250 .938 TABLE I. Dash numbers and size Continued. 1/ 2/ Dash number Tubing outside diameter Thread T AND10089 B +1.194 -.000 C +1.194 -.000 E +1.194 -.000 R 381 Rad
5、W .381 Brass Corrosion resistant steel 2 C2 3.175 .3125-32 UNEF-3A 15.875 15.875 15.875 1.575 7.925 3 C3 4.267 .3750-24 UNF-3A 17.475 17.475 17.475 9.525 4 C4 6.350 .4375-20 UNF-3A 19.050 19.050 19.050 2.388 11.125 5 C5 7.925 .5000-20 UNF-3A 22.225 22.225 22.225 6 C6 9.525 .6250-18 UNF-3A 25.4 25.4
6、25.4 3.175 15.875 8 C8 12.700 .7500-16 UNF-3A 30.175 30.175 30.175 19.05 10 C10 15.875 .9375-14 NS-3 31.75 31.75 31.75 23.825 1/ Dimensions are in inches 2/ Metric equivalents are given for information only. AN795 Rev52Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
7、nse from IHS-,-,-AN795 Rev 5 3 REQUIREMENTS Dimensions. See table I. Unless otherwise specified tolerances on decimals are .010, angles 0.5. Configuration. See figure 1. Dash numbers 2, 3 and 4 are inactive for new design except for use in oxygen systems and engine primer lines. Dash numbers 5, 6, 8
8、 and 10 are inactive for new design and are not to be used on engine primer lines. Materials: Brass; bars, shapes or forgings. Corrosion resistant steel; bars, shapes or forgings. See procurement specification. Finish: See procurement specification. Identification of product. Add P before the dash n
9、umber for cadmium plated brass nipple. AN795 X X Size Material, finish Drawing number Example of Part or Identifying Number (PIN): AN795-4 tee union, brass, for .250 tubing OD. AN795P4 tee union, brass, cadmium plated, for .250 tubing OD. AN795C4 tee union, corrosion resistant steel, for .250 tubing
10、 OD. Workmanship. Break all sharp edges and remove all hanging burrs and slivers which might become dislodged under usage. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced
11、 documents. In addition to MIL-DTL-6001, this document references the following: AND10089 CONCLUDING MATERIAL Custodians: Preparing activity: Army AR DLA - CC Navy SH Air Force - 99 DLA - CC (Project 4730-2010-183) Review activities: Army AT, AV, CR4 Navy AS, CG, MC, SA, YD Air Force - 71 NOTE: The
12、activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
