1、NOTICE OF REVISION (NOR)THIS REVISION DESCRIBED BELOW HAS BEEN AUTHORIZED FOR THE DOCUMENT LISTED.1. DATE(YYMMDD)99-03-10Form ApprovedOMB No. 0704-0188Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewinginstructions, searching exi
2、sting data sources, gathering and maintaining the data needed, and completing and reviewing thecollection of information. Send comments regarding this burden estimate or any other aspect of this collection of information,including suggestions for reducing this burden, to Department of Defense, Washi
3、ngton Headquarters Services, Directorate forInformation Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503.PLEASE DO NOT RETURN YOUR COMPLETED FORM TO EI
4、THER OF THESE ADDRESSED. RETURN COMPLETEDFORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITYNUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURINGACTIVITY NO.3. DODAAC4. ORIGINATORb. ADDRESS (Street, City, State, Zip Code)Defense Supply Center, Columbus3990 East Broad
5、StreetColumbus, OH 43216-50005. CAGE CODE672686. NOR NO.5962-R040-99a. TYPED NAME (First, Middle Initial,Last)7. CAGE CODE672688. DOCUMENT NO.5962-985369. TITLE OF DOCUMENTMICROCIRCUIT, DIGITAL, RADIATION HARDENED ADVANCED CMOS,QUAD 2-INPUT MULTIPLEXER, WITH NON-INVERTING OUTPUTS,10. REVISION LETTER
6、11. ECP NO.No users listed.MONOLITHIC SILICON a. CURRENTIn itialb. NEWA12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESAll13. DESCRIPTION OF REVISIONSheet 1 : Revisions ltr column; add “A“.Revisions description column; add “ Changes in accordance with NOR 5962-R040-99“.Revisions date column ;
7、 add “99-03-10“.Revision level block; add “A“.Rev status of sheets; for sheets 1, 4 and 17 through 23, add “A“.Sheet 4 : Add new paragraph which states; “3.1.1 Microcircuit die . For the requirements for microcircuit die, see appendix A tothis document.“Revision level block; add “A“.Sheets 17 throug
8、h 23: Add attached appendix A.CONTINUED ON NEXT SHEETS14. THIS SECTION FOR GOVERNMENT USE ONLYa. (X one) X (1) Existing document supplemented by the NOR may be used in manufacture.(2) Revised document must be received before manufacturer may incorporate this change.(3) Custodian of master document s
9、hall make above revision and furnish revised document.b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FORGOVERNMENTDSCC -VACc. TYPED NAME (First, Middle Initial, Last)MONICA L. POELKINGd. TITLECHIEF, CUSTOM MICROELECTRONICS TEAMe. SIGNATUREMONICA L. POELKINGf. DATE SIGNED(YYMMDD)99-03-1015a. ACTIVITY ACCOM
10、PLISHING REVISIONDSCC -VACb. REVISION COMPLETED (Signature)LARRY T. GAUDERc. DATE SIGNED(YYMMDD)99-03-10DD Form 1695, APR 92 Previous editions are obsolete.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DE
11、FENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 17DSCC FORM 2234APR 97Document N o : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet: 2 of 8 10. SCOPE10.1 Scope . This appendix establishes minimum requirements for micro
12、circuit die to be supplied under the QualifiedManufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturersapproved QM plan for use in monolithic microcircuits, multichip modules (MCMs), hybrids, electronic modules, or devices usingchip and wi
13、re designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting ofmilitary high reliability (device class Q) and space application (device Class V) are reflected in the Part or Identification Number(PIN). When available a choice of Radiation Hardiness Assur
14、ance (RHA) levels are reflected in the PIN.10.2 PIN . The PIN shall be as shown in the following example:5962 F 98536 01 V 9 AFederal RHA Device Device Die DieStock class designator type c lass code Detailsdesignator (see 10.2.1) (see 10.2.2) designator (see 10.2.4)( see 10.2.3) Drawing Number 10.2.
15、1 RHA designator . Device classes Q and V RHA identified die shall meet the MIL-PRF-38535 specified RHA levels. Adash (-) indicates a non-RHA die.10.2.2 Device type(s) . The device type(s) shall identify the circuit function as follows:Device type Generic number Circuit function01 ACS157 Radiation H
16、ardened, SOS, advanced CMOS, quad 2-input multiplexer with non-inverting outputs10.2.3 Device class designator .Device class Device requirements documentationQ or V Certification and qualification to the die requirements of MIL-PRF-38535.Provided by IHSNot for ResaleNo reproduction or networking per
17、mitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 18DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet: 3 of
18、 8 10.2.4 Die Details . The die details designation shall be a unique letter which designates the dies physical dimensions, bondingpad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product andvariant supplied to this appendix.10
19、.2.4.1 Die Physical dimensions .Die Type Figure number01 A-110.2.4.2 Die Bonding pad locations and Electrical functions .Die Type Figure number01 A-110.2.4.3 Interface Materials .Die Type Figure number01 A-110.2.4.4 Assembly related information .Die Type Figure number01 A-110.3 Absolute maximum rati
20、ngs . See paragraph 1.3 within the body of this drawing for details.10.4 Recommended operating conditions . See paragraph 1.4 within the body of this drawing for details.20. APPLICABLE DOCUMENTS20.1 Government specifications, standards, bulletin, and handbooks . Unless otherwise specified, the follo
21、wing specifications,standards, bulletin, and handbook of the issue listed in that issue of the Department of Defense Index of Specifications andStandards specified in the solicitation, form a part of this drawing to the extent specified herein.Provided by IHSNot for ResaleNo reproduction or networki
22、ng permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 19DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet
23、: 4 of 8 SPECIFICATIONDEPARTMENT OF DEFENSEMIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.STANDARDSDEPARTMENT OF DEFENSEMIL-STD-883 - Test Methods and Procedures for Microelectronics.HANDBOOKDEPARTMENT OF DEFENSEMIL-HDBK-103 - List of Standardized Military Drawings (SM
24、Ds).(Copies of the specification, standards, bulletin, and handbook required by manufacturers in connection with specific acquisitionfunctions should be obtained from the contracting activity or as directed by the contracting activity).20.2 Order of precedence . In the event of a conflict between th
25、e text of this drawing and the references cited herein, the text ofthis drawing shall take precedence.30. REQUIREMENTS30.1 Item Requirements . The individual item requirements for device classes Q and V shall be in accordance withMIL-PRF-38535 and as specified herein or as modified in the device man
26、ufacturers Quality Management (QM) plan. Themodification in the QM plan shall not effect the form, fit or function as described herein.30.2 Design, construction and physical dimensions . The design, construction and physical dimensions shall be as specified inMIL-PRF-38535 and the manufacturers QM p
27、lan, for device classes Q and V and herein.30.2.1 Die Physical dimensions . The die physical dimensions shall be as specified in 10.2.4.1 and on figure A-1.30.2.2 Die bonding pad locations and electrical functions . The die bonding pad locations and electrical functions shall be asspecified in 10.2.
28、4.2 and on figure A-1.30.2.3 Interface materials . The interface materials for the die shall be as specified in 10.2.4.3 and on figure A-1.30.2.4 Assembly related information . The assembly related information shall be as specified in 10.2.4.4 and figure A-1.30.2.5 Truth table . The truth table shal
29、l be as defined within paragraph 3.2.3 of the body of this document.30.2.6 Radiation exposure circuit . The radiation exposure circuit shall be as defined within paragraph 3.2.6 of the body of thisdocument.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
30、,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 20DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 S heet: 5 of 8 30.3 Electrical performance
31、characteristics and post- irradiation parameter limits . Unless otherwise specified herein, theelectrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document.30.4 Electrical test requirements . The wafer probe test requirements s
32、hall include functional and parametric testing sufficient tomake the packaged die capable of meeting the electrical performance requirements in table I.30.5 Marking . As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer,shall be identified
33、with the wafer lot number, the certification mark, the manufacturers identification and the PIN listed in 10.2herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535.30.6 Certification of compliance . For device classes Q and V, a certificate of compliance shall be requir
34、ed from aQML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 60.4 herein). The certificate ofcompliance submitted to DSCC-VA prior to listing as an approved source of supply for this appendix shall affirm that themanufacturers product meets, for device classes Q
35、 and V, the requirements of MIL-PRF-38535 and the requirements herein.30.7 Certificate of conformance . A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shallbe provided with each lot of microcircuit die delivered to this drawing.40. QUALITY ASSURANCE PROVISIONS40
36、.1 Sampling and inspection . For device classes Q and V, die sampling and inspection procedures shall be in accordancewith MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modifications in the QMplan shall not effect the form, fit or function as described he
37、rein.40.2 Screening . For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in themanufacturers QM plan. As a minimum it shall consist of:a) Wafer Lot acceptance for Class V product using the criteria defined within MIL-STD-883 TM 5007.b) 100% wafer probe (s
38、ee paragraph 30.4).c) 100% internal visual inspection to the applicable class Q or V criteria defined within MIL-STD-883 TM2010or the alternate procedures allowed within MIL-STD-883 TM5004.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICRO
39、CIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 21DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet: 6 of 8 40.3 Conformance inspection .40.3.1 Group E in
40、spection . Group E inspection is required only for parts intended to be identified as radiation assured (see30.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing ofpackaged die shall be as specified in table IIA herein. Group E tests
41、 and conditions are as specified within paragraphs 4.4.4.1,4.4.4.1.1, 4.4.4.2, 4.4.4.3 and 4.4.4.4.50. DIE CARRIER50.1 Die carrier requirements . The requirements for the die carrier shall be in accordance with the manufacturers QM plan oras specified in the purchase order by the acquiring activity.
42、 The die carrier shall provide adequate physical, mechanical andelectrostatic protection.60. NOTES60.1 Intended use . Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance withMIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (ori
43、ginal equipment), design applications and logisticspurposes.60.2 Comments . Comments on this appendix should be directed to DSCC-VA, Columbus, Ohio, 43216-5000 or telephone(614)-692-0674.60.3 Abbreviations, symbols and definitions . The abbreviations, symbols, and definitions used herein are defined
44、 withMIL-PRF-38535 and MIL-HDBK-1331.60.4 Sources of Supply for device classes Q and V . Sources of supply for device classes Q and V are listed in QML-38535.The vendors listed within QML-38535 have submitted a certificate of compliance (see 30.6 herein) to DSCC-VA and have agreedto this drawing.Pro
45、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 22DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R
46、040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet: 7 of 8 FIGURE A-1o DIE PHYSICAL DIMENSIONSDie Size: 2390 x 2390 microns.Die Thickness: 21 +/-2 mils.o DIE BONDING PAD LOCATIONS AND ELECTRICAL FUNCTIONSThe following metallization diagram supplies the locations and electrical functions of the bo
47、nding pads. The internal metallizationlayout and alphanumeric information contained within this diagram may or may not represent the actual circuit defined by this SMD.NOTE: Pad numbers reflect terminal numbers when placed in Case Outlines E, X (see Figure 1).Provided by IHSNot for ResaleNo reproduc
48、tion or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA 5962-98536DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 23DSCC FORM 2234APR 97Document No : 5962-98536Revision: AAPPENDIX A NOR No: 5962-R040-99APPENDIX A FORMS A PART OF SMD 5962-98536 Sheet: 8 of 8 o INTERFACE MATERIALSMetal 1: AlSi 7.0kA +/- 1.0kAMetal 2 (Top ) : AlSi 10.0kA +/- 1.0kABackside Metallization NoneGlassivationType: PSGThickness 13 .0kA +/ - 1.5kASubstrate: Silicon on Sapphire (SOS)o ASSEMBLY RELATED INFORMATIONSubstrate
