FORD M2C170-A-2009 OIL - ENGINE LUBRICATING SYNTHETIC《引擎用合成润滑油》.pdf

上传人:twoload295 文档编号:747958 上传时间:2019-01-14 格式:PDF 页数:2 大小:27.45KB
下载 相关 举报
FORD M2C170-A-2009 OIL - ENGINE LUBRICATING SYNTHETIC《引擎用合成润滑油》.pdf_第1页
第1页 / 共2页
FORD M2C170-A-2009 OIL - ENGINE LUBRICATING SYNTHETIC《引擎用合成润滑油》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 15 N-STATUS No Replacement Named L. Sinclair, FNA 1982 01 01 Page 1 of 2 OIL - ENGINE, LUBRICATING, SYNTHETIC M2C170-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The oil defined by this Standard is a h

2、eavy-duty engine oil, 5W-30 grade, compounded from synthetic hydrocarbons and selected esters. 2. APPLICATION: This oil is generally used in automotive gas and diesel engines in on and off highway vehicles and other heavy-duty industrial engines. 3. REQUIREMENTS: 3.1 VISCOSITY: (ASTM D 445) at 210 F

3、 (99 C) 17.98 - 22.70 cSt (mm2/s) (ASTM D 2602) at 104 F (40 C) 12,500 cP minimum (mPa . s) 3.2 VISCOSITY INDEX: 160 minimum (ASTM D 2270) 3.3 FLASH POINT: 440 F (ASTM D 92) (227 C) minimum 3.4 FIRE POINT: 480 F (ASTM D 92) (250 C) minimum 3.5 POUR POINT: -65 F (ASTM D 97) (-54 C) maximum 3.6 GRAVIT

4、Y: A.P.I. 30.7 minimum (ASTM D 287) 3.7 SULPHATED ASH: 1.0 percent maximum (ASTM D 874) 3.8 TBN: 6.3-7.7 mgKOH/g (ASTM D 2896) 3.9 SUPPLIERS RESPONSIBILITY: All materials supplied to this Standard must be equivalent in all characteristics to the material upon which approval was originally granted an

5、d shall be suitable for the intended application. Changes in composition shall not be made without approval of the Plant Engineering Maintenance and Internal Environmental Engineering Department, Plant Engineering Office. NON-PRODUCTION MATERIAL SPECIFICATION M2C170-A Page 2 of 2 3.10 IDENTIFICATION

6、: Materials supplied to this Standard shall be identified with the M-number printed on the side, as well as on the top of the containers in letter at least 2 inches high in a contrasting color to that of the container. Container marking shall be in accordance with Manufacturing Standard ZF-10 and co

7、nform to all Federal, State and local container contents labeling regulations which are in effect both in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this Standard must have laboratory and shop trial approvals. Recommendations for the addit

8、ion of new manufacturers to the Manufacturing Standards Approved Source List must be made by the appropriate Division Standards activity in writing to the Maintenance and Internal Environmental Engineering Department, Plant Engineering Office. All supporting data must accompany the written request.

9、5. ENVIRONMENTAL CONTROL: Suppliers are required to report to the plants using the material, a listing of those constituents present in the material which appear on the Register of Critical Materials, as established by the Michigan State Water Resources Commission (Ford Motor Company Form 68-100). I

10、n addition, suppliers also will comply with any other national, state, territorial or other political subdivision requirement for the disclosure of materials other than those appearing on the Michigan Register of Critical Materials. 6. HEALTH AND SAFETY: The following are recommended practices to be

11、 observed when working with petroleum products: 6.1 Where contact with oil is unavoidable, impervious gloves should be worn. Clean work clothes should be worn. If extensive splashing cannot be avoided, impervious aprons and footwear should be worn. 6.2 When skin exposure cannot be avoided, removal of oil from the skin should be as prompt as possible. Industrial solvents should not be used to clean the skin. 6.3 All skin rashes, lesions, cuts and abrasions should receive prompt medical attention.

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1