1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/19E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/19D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, SINGLE CABLE, TYPE III, 65-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use by all Departments
2、and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 7. 2. The gland nut shall be tightened until the packing tightens a
3、gainst the wires. This can be determined by moving the wires gently back and forth until the wire is seized by the packing. The gland nut shall be turned approximately one-fourth of a turn more to hold the wires in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as
4、 this can damage the wires. 3. Refer to MIL-DTL-24231/5 for alternate method of manufacturing connector body and installing guide pin M24231/5-071. 4. Welding of the pin is allowed after the hull fitting body has been age-hardened to achieve its required physical properties. 5. The retainer plates a
5、nd retainer plate assemblies shall be manufactured from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281 with a minimum yield strength of 40,000 lbf/in2 at 0.2 percent offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of
6、 QQ-N-281 with a minimum yield strength of 50,000 lbf/in2 at 0.2 percent offset. 6. All dimensions are in inches. 7. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. 8. These connectors are for maintenance purposes only. Provi
7、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/19E(SH) 2 FIGURE 1. Connector, single cable. NUT, GLA NDM24231/19- 0 2 3( SEE REQ T 2 )SLEEVING 114I. D.X 0. 035 THK, A P P RO X10 FEET L O NGASSEMBLY, SI NGLE CABLE CO NN E CT O RM24231/19- 00
8、1 SYM . NO . 1 1 3 8WAS HE RM24231/19- 0 2 5NUT, R O UN DM24231/19- 0 2 4RI NG, RET A I NI NGM24231/19- 0 1 4ASSEMBLY, HULL IN S E RTM24231/25- 00 3 (N O TFURNI SH E D)GASKET, O -R I NGSAE-AS28775 -3 3 9PACKING ,M24231/19- 0 2 2PLATE, RET A I NE RM24231/19- 0 2 1PIN, GUI DE 0 . 1 2 5 ,LG AS RE Q D(
9、SEE REQT 3 see figure 1. 8 Gasket, O-ring 1 SAE-AS28775-334 4/ See item 7. 9 Gasket, O-ring 1 SAE-AS28775-342 4/ See item 7. 10 Gasket, O-ring 1 SAE-AS28775-339 4/ See item 7. 11 Insert 1 Nylon, Group 1, Class 1, ASTM D4066 See item 7. 12 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure
10、 4. 13 Sleeving, 1 id by 0.035 thick 10 ft Type F, Form U, Category 1, color clear, MIL-I-631 See figure 1. 14 Ring, retaining, M24231/19-011 1 SPIROLOX, RR-262 5/ See figure 1. 15 Ring, retaining, M24231/19-014 1 SPIROLOX, RST-312S 5/ See figure 1. 16 Nut, round 1 Ni-Cu-Al, QQ-N-286 See figure 3. 1
11、7 Washer, 4 od by 3.260 id by 0.187 thick 1 See item 16. See figure 1. 18 Nut, gland 1 Ni-Al-BRZ, ASTM B150/B150M See figure 5 and requirement 2. 19 Pin, guide, 0.125 diameter, length to suit 1 Ni-Cu, Class A, QQ-N-281 See requirements 3 and 4. 20 Cap, pressure-proof 1 M24231/22-054 See figure 1. 21
12、 Plate, retaining 1 Ni-Cu, Class A, QQ-N-281 See figure 7 and requirement 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/19E(SH) 9 TABLE I. Parts list Continued. NOTES: 1/ Item numbers are the same as encircled numbers shown on figu
13、res. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or eq
14、ual. 5/ Manufactured by Ramsey Corp., St. Louis, MO, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-068) NOTE: The activiti
15、es listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
