1、MIL-STD-1612B 17 October 1988 SUPERSEDING MIL-STD-1612A 18 April 1980 MI LI TARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF GLOVES, CLOTH, DRESS FSC 8440-8445 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. THIS DOCUMENT CONTAINS 15 PAGES. Provided by IH
2、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1612B FOREWORD . 1. This Military Standard is approved for use by all Departments and Agencies of the Department of Defense. 2. Beneficial comments (recommendations, additions, deletions) and any pertinent da
3、ta which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, Ma 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this do
4、cument or by letter. 3. This document supplements the military specifications listed below. It provides a standard description for defects and standardizes examination requirements. Title Gloves, Womens Gloves, Mens, Cloth, Dress, White Gloves, Cloth, Nylon Knitted (Womens Dress) ii . Provided by IH
5、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-Lb32B BL( 9997931 0082723 O Fh 1.1 1.2 2. 2.1 2.1.1 2.2 3. 3.1 3.2 3.3 3.4 4 5 5.1 E 5.4 5.5 5.6 5.7 5.7.1 5.7.2 5.7.3 5.7.4 6 6.1 6.2 6.3 6.4 Table MIL-STD-1612B CONTENTS SCOPE scope Application APPLICABLE D
6、OCUMENTS Government documents Order of precedence Specification, standards, and handbooks DEFINITIONS Fabric defects Knots and slubs Quality assurance terms and procedures Open seam GENERAL REQUIREMENTS DETAILED REQU1RE“S End item examination Dimensional examination Packaging inspection Inspection p
7、rocedures Initiation of inspection Continuation of inspection Switching procedures Normal to tightened Tightened to normal Normal to reduced Reduced to normal NOTES Intended use Issue of DODISS Changes from previous issue Subject term (key word) listing I Sampling Provision for Cloth Dress Gloves II
8、 Classification of Defects 1 1 2 2 2 2 3 3 3 3 3 3 4 4 4 5 7 iii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-Lb12B 8q m 77797LL O082722 2 m MIL-STD-1612B 1. SCOPE 1.1 scope. The scope of this standard is to provide standardized provisions
9、 for evaluating the quality of cloth dress gloves. 1.2 App lication. This standard will be made applicable to contracts by references in the appropriate glove specifications. if there are any inconsistencies between the requirements of the applicable specification and this standard, the specificatio
10、n will govern. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those lis
11、ted in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). STANDARD MILITARY MIL-STD-105 MIL-STD-109 MIL-STD-1491 - Sampling Procedures and Tables for - Quality Assurance Terms and - Glossary of Knitting I
12、mperfections Inspection by Attributes Definitions (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (Al“: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.2 Order of precedence. I
13、n the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable law and regulations unless a specified exemption has been obtained. 3. DEFINITIONS 3.1 Fabric defects. The
14、 fabric defect definitions applicable to the standard are described in FED-STD-1491. Fabric defects shall be clearly visible when examined at a distance of 3 feet. 3.2 Knots and slubs. Only knots and slubs that exceed the limits specified in the basic cloth specification and are clearly visible when
15、 examined at a distance of 3 feet shall be scored as defects in evaluating quality of glove. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1612B 3.3 Quality assurance terms and procedures. Quality assurance terms and procedures, when appl
16、icable, shall be in accordance with MIL-STD-105 and MIL-STD-109. 3.4 Open seam. The seam shall be classified open when one or more stitches joining a seam are broken or runoff, or when two or more continuous skipped or runoff stitches occur. 4. GENERAL REQUIREMENTS 4.1 This standard contains the pro
17、visions for end item examination, dimensional examination, and packaging inspection for cloth dress gloves. This standard assigns to the listed defects point values of 1, 2, or 3 depending on degree of severity. The higher point values are assigned to those defects having more detrimental effect on
18、the appearance or serviceability of the item. 5. DETAILED REQUIFWENTS 5.1 End item examination. The gloves shall be examined and all defects shall be penalized as indicated in Table II of this standard. The sample size shall be based on lot size, and the acceptance value for 3 and 2 point defects an
19、d total (3, 2, and 1 point) defects shall be as specified in Table I. The sample unit shall be one glove and the selection shall be by pairs. Defects for pairing shall be classified as a single defect, The lot shall be unacceptable if: a. The point value of 3 and 2 point defects exceeds the applicab
20、le maximum acceptable point value. OR b. The point value for total (3, 2, and 1 point) defects exceeds the applicable maximum point value. 5.2 Dimensional examination. The appropriate number of gloves selected in pairs and as determined from the table below, shall be examined for conformance to the
21、dimensional requirements cited in the table of measurements of the appropriate glove specification. When a measurement deviates from a dimension and tolerance specified, the glove shall be penalized one point. The lot shall be unacceptable if the total point value exceeds the maximum acceptable poin
22、t value specified below. Each size glove present in the lot shall be represented in the sample selected for this examination. Lot size Up thru 500 Sample size Maximum Acceptable Point Values a O 51 thru 3200 13 1 3201 thru 35,000 20 2 35,001 and up 32 3 2 Provided by IHSNot for ResaleNo reproduction
23、 or networking permitted without license from IHS-,-,-, - MIL-STD-Lb12B 8Lt 97997LL 0082724 b MIL-STD-1612B 5.3 Packaging Inspection. An examination shall be made to determine that packaging, packing, and marking requirements are in compliance with Section 5 of the appropriate. glove specification.
24、Defects listed below shall be scored one point. The sample size for this examination shall be five shipping containers fully prepared for delivery with the exception that they need not be closed. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. Th
25、e lot shall be unacceptable if one or more points are scored for this examination. o Examine Marking (exterior and interior Elate ri al s Workmanship Content Defect Omitted, incorrect, illegible, or improper size, location, sequence, or method of application. Any component missing, damaged, or not a
26、s specified. Inadequate application of components, such as: incomplete closure of container, flaps, loose strapping, improper taping, inadequate stapling, or open and non-continuous heat sealed seams of polyethylene bag. Bulging or distorted container. Number of intermediate packages per shipping co
27、ntainer is more or less than required. Number of pairs of gloves per intermediate package is more or less than required. 1/ - - i/ For this defect, two intermediate packages shall be examined from each shipping container in the sample. 5.4 Inspection Procedures. Inspection shall be as specified in M
28、IL-STD-105, except where otherwise indicated in this document. 5.5 Initiation of inspection. Normal inspection will be used at the start of inspection unless otherwise directed by the procurement quality assurance element administrating the contract. 5.6 Continuation of inspection. Normal, tightened
29、, or reduced inspection shall continue unchanged on successive lots except where switching procedures in 5.7 require change. 5.7 Switching procedures. 5.7.1 Normal to tightened. When normal inspection is in effect, tightened inspection shall be instituted when two out of five consecutive lots have b
30、een rejected on original inspection (e.i., ignoring resubmitted lots for this procedure. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I-_ - MIL-STD-LbL2B 84 W 77777LL 0082725 8 W MIL-STD-1612B 5.7.2 Tightened to normal. When tightened inspection
31、is in effect, normal inspection shall be reinstituted when five consecutive lots have been considered acceptable on original inspection. 5.7.3 Normal to reduced. When normal inspection is in effect, reduced inspection shall be instituted providing that all of the following conditions are satisfied:
32、a. The preceding 10 lots have been on normal inspection and none have been rejected on original inspection; and b. The total number of points for 3 and 2 point defects in the samples from the preceding 10 lots is equal to or less than sixty percent of the total maximum acceptable point values for 3
33、and 2 point defects from the preceding 10 lots; and c. The total number of points for 3, 2 and 1 point defects in the sample from the preceding 10 lots is equal to or less than seventy-five percent of the total maximum acceptable point values for 3, 2, and 1 point defects from the preceding 10 lots;
34、 and d. Production is at a steady rate; and e. Reduced inspection is considered desirable by the procurement quality assurance element administering the contract. 5.7.4 Reduced to normal. When reduced inspection is in effect, normal inspection shall be instituted if any of the following occur on ori
35、ginal inspection: 0 a. A lot is rejected; or *b. A lot is considered acceptable but exceeds the applicable first value c. Production becomes irregular or delayed; or d. Other conditions warrant that normal inspection be reinstituted. (see - 1/to Table I); or 4 Provided by IHSNot for ResaleNo reprodu
36、ction or networking permitted without license from IHS-,-,-MIL-STD-LbL2B 84 77777LL 0082726 T MIL-STD-1612B Table I - Sampling provisions for Cloth Dress Gloves Maximum Acceptable Point Values Sample 3 more than 1/2 inch (largest dimension in any direction) on outside II. SHADED PARTS a. Any part sh
37、aded or variation in shade within a part: 1. On outside 2. On inside III. a. Spot or stain on outside (largest dimension in any direction): 1. Up to 1/4 inch, inclusive 2. More than 1/4 inch b. Thread ends - on outside: 1. More than one but not more than three not trimmed to less than 1/2 inch 2. Mo
38、re than three not trimmed to less than 1/2 inch 3 1 2 3 1 1 2 1 2 c. Two or more shade or size tickets not removed d. Surplus material on seams not trimmed throughout glove 1 e. Any size or shade marking on outside, score as spot or stain (see IIa) 1 7 Provided by IHSNot for ResaleNo reproduction or
39、 networking permitted without license from IHS-,-,- _ - MIL-STD-Lb12B 84 999791L 0082729 5 W MIL-STD-1612B Table II - Classification of defects Point Value IV. CUTTING - ny component part not cut in accordance with specified pattern, directional lines on patterns, or not in accordance with specifica
40、tion requirements 3 V. comms AND ASSEMBLY a. Any component part or operation omitted (unless otherwise classified herein) 3 b, Any component not as specified 3 C. Any component part, tight, twisted, distorted, d. Any operation not as specified (unless otherwise pleated, or full (unless otherwise cla
41、ssified herein) 2 classified herein) 2 VI. SEAMS AND STITCHING a. Accuracy of seaming: 1. Seam puckered 2. Seam irregular, pleated, or wavy 3. Any part of glove caught in an unrelated ope rat ion 4. Ends of stitching produced with 301 stitch type, when not caught in other seams or stitching, backtac
42、ked less than specified 5. Ends of stitching produced with 401 stitch type, when not caught in other seams or stitching, not having chain extending beyond each end 6. Ends of stitching produced with 401 stitch type, when not caught in other seams or stitching, having chain extending less than 1/2 in
43、ch or more than 3/4 inch beyond each end 7. Thread breaks (all stitch types) stitched less than 1/2 inch beyond each end of break b. Gage of stitching and seam allowance: 1. Stitching irregular, not within range specified, or varies more than 1/16 inch when no range is specified (score only when con
44、dition exists on more than half the length of seam) 2. Width of seam allowance varies more than 1/16 inch from allowance specified (score only when condition exists on more than half the length of seam) 2 2 2 1 2 1 1 1 2 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without
45、license from IHS-,-,-v w MIL-STD-LbL2B 4 H 77777LL 0082730 L M MIL-STD-1612B Table II - Classification of defects VI. SEAMS AND STITCHING CONT O Point Value c. Open seam or stitching (see 3.4): d. Runoff, skipped, or broken stitches: 1. On all seam, except pointing or hem stitching 3 1. On joining s
46、eam - when resulting in an open 2. On pointing stitching: seam, use “Open seam or stitching“ classification (a) - one skipped or broken stitch (b) - two or three skipped or broken stitches (c) - four or more skipped or broken stitches (a) - up to 1/4 inch, inclusive 1 (b) - more than 1/4 inch 1 2 3
47、3. On hem stitching: 2 e. Seam and stitch type: 1. Not specified seam or stitch type 2. Any line of stitching omitted 2 3 1 3. Any line of stitching misplaced or not 4. Looper thread of 401 stitch type on outside beginning or ending when specified (outseam constructed glove) 3 f. Stitch tension: 3 2
48、 1. Loose tension resulting in a loose seam 2. Loose tension on hem or pointing stitching, 3. Tight tension (stitches break when normal strain is applied in the direction of the seam or resulting in loosely exposed thread stitching) 3 g. Stitches per inch (to be scored only when the condition exists
49、 on the major portion of seam or stitching): 1. Less than the minimum 2. More than the maximum h. Stitches or “V“ points for attaching elastic webbing: 1. For Zig-Zag stitching - stitch type 304: (a) - less than the minimum (b) - more than the maximum 2, For Zig-Zag stitching - stitch type 301: (a) - less than the minimum (b) - more than the maximum 3. For Zig-Zag stitch pattern - s
