NEN 2976-1986 Stainless steel equilateral longitudinal welded tees《不锈钢等边纵向焊接三通接头》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 8362-1-2009 en Injection containers and accessories - Part 1 Injection vials made of glass tubing (Incorporates Amendment A1 2015)《注射容器和附件 第1部分 玻璃管制注射管》.pdf

EN ISO 8362-2-2010 2500 Injection containers and accessories - Part 2 Closures for injection vials《注射容器和附件 第2部分 注射瓶用瓶塞》.pdf

EN ISO 8362-2-2015 en Injection containers and accessories - Part 2 Closures for injection vials《注射容器及配件 第5部分 冷冻干燥瓶塞注射瓶(ISO 8362-2 2015)》.pdf

EN ISO 8362-3-2003 en Injection containers and accessories Part 3 Aluminium caps for injection vials《注射剂用注射器容器及附件 第3部分 注射瓶铝盖 ISO 8362-3-2001 代替EN 28362-3-1993》.pdf

EN ISO 8362-4-2011 en Injection containers and accessories - Part 4 Injection vials made of moulded glass《注射容器及附件 第4部分 模压玻璃制成的注射液瓶》.pdf

EN ISO 8362-5-2016 en Injection containers and accessories - Part 5 Freeze drying closures for injection vials《注射容器和附件 第5部分 注射瓶用冷冻干燥塞》.pdf

EN ISO 8362-6-2011 en Injection containers and accessories - Part 6 Caps made of aluminium-plastics combinations for injection vials《注射剂用注射容器及附件 第6部分 铝塑组合注射瓶盖》.pdf

EN ISO 8362-7-2010 en Injection containers and accessories - Part 7 Injection caps made of aluminium-plastics combinations without overlapping plastics part《注射容器及附件 无重叠塑料部件的铝塑组合制成的.pdf

EN ISO 8367-1-1996 en Packaging - Dimensional Tolerances for General Purpose Sacks - Part 1 Paper Sacks《包装 一般用途袋子的尺寸公差 第1部分 纸袋 ISO 8367-1-1993》.pdf