1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, REVERSE BAYONET COUPLING, JAM NUT AS95234/7Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, r
2、ecording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-01THIRD ANGLE PROJECTION CUSTODI
3、AN: AE-8/AE-8C1 REV.X FEDERAL SUPPLY CLASS 5970 AS95234/7 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS95234SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicab
4、ility and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggesti
5、ons. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS95234/7 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO STANDARDIZE COMMERCIAL CONNECTORS FOR USER APPLICATIONS. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE P
6、RODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS95234. FIGURE 1 - CONNECTOR JAM NUT RECEPTACLE AEROSPACE STANDARD AS95234/7 SHEET 2 OF 2 CONNECTOR, RECEPTACLE, REVERSE BAYONET COUPLING, JAM NUT TABLE 1 - FIGURE 1 DIMENSIONS SHELL SIZE FRONT VIEW SIDE VIEW R .004 (0.1
7、) S .012 (0.3) T MAXIMUM A +.000/-.006 (+0.00/-0.15) B PANEL THICKNESS K .008 (0.2) M +.016/-.000 (+0.4/-0.0) V THREAD CLASS 2A MIN. MAX. 10SL 1.063 (27.0) 1.252 (31.8) .441 (11.2) .717 (18.2) .094 (2.4) .205 (5.2) .157 (4.0) .965 (24.5) 7/8-20 UNEF 14S 1.299 (33.0) 1.626 (41.3) .575 (14.6) .969 (24
8、6) .295 (7.5) .189 (4.8) 1.055 (26.8) 1 1/8-18 UNEF 16S 1.500 (38.1) 1.748 (44.4) .618 (15.7) 1.079 (27.4) 1 1/4-18 UNEF 16 1.500 (38.1) 1.748 (44.4) .618 (15.7) 1.079 (27.4) 1.264 (32.1) 18 1.563 (39.7) 1.874 (47.6) .661 (16.8) 1.213 (30.8) .354 (9.0) 1.327 (33.7) 1 3/8-18 UNEF 20 1.732 (44.0) 2.0
9、00 (50.8) .709 (18.0) 1.346 (34.2) 1 1/2-18 UNEF 22 1.811 (46.0) 2.134 (54.2) .795 (20.2) 1.472 (37.4) .358 (9.1) 1 5/8-18 UNEF 24 2.000 (50.8) 2.252 (57.2) .795 (20.2) 1.610 (40.9) 1.386 (35.2) 1 3/4-18 UNEF 28 2.165 (55.0) 2.500 (63.5) .886 (22.5) 1.839 (46.7) .335 (8.5) .220 (5.6) 2-18 UNS 32 2.4
10、41 (62.0) 2.748 (69.8) .972 (24.7) 2.102 (53.4) .256 (6.5) 2 1/4-16 UN 36 2.795 (71.0) 3.000 (76.2) 1.059 (26.9) 2.346 (59.6) .327 (8.3) 2 1/2-16 UN REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS95234. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WT
11、H FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS ARE GIVEN FOR INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. 2. FOR INSERT ARRANGEMENTS, SEE AS95234, APPENDIX B. 3. PART NUMBER: THE PART NUMBER SHALL BE AS SHOWN IN THE
12、 EXAMPLE BELOW: SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
