1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2012 SAE International All rights reserved. No part of this pub
3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970
4、outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J1693_201204SURFACEVEHICLERECOMMENDEDPRACTICEJ1693 APR2012 Issued 1994-06Stabilized
5、2012-04 Superseding J1693 JUN1994 Remanufactured Hydraulic Master Cylinder for Motor Vehicle Brakes - General Characteristicsand Test Procedure RATIONALEThis document has been determined to contain basic and stable technology, however it does not specifically represent the current state of the art d
6、esign of tandem master cylinders for passenger vehicles and light trucks. Although this Recommended Practice is not directly applicable to many current master cylinder designs, it does incorporate procedures and requirements that can be appropriate and beneficial. Many aspects of these can be applie
7、d to designs of the same or similar concept including aluminum body as well as more current state of the art designs.Figure 3 represents the typical cast iron master cylinder for which this standard was developed. Equivalent designs, regardless of materials utilized, could employ portions of this Re
8、commended Practice to evaluate remanufactured products.STABILIZED NOTICE This document has been declared “Stabilized“ by the SAE Hydraulic Brake Components Standards Committee and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continu
9、ed suitability of technical requirements. Newer technology may exist. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 1 of 12 Copyright SAE International Provided by
10、 IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 2 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,
11、SAE J1693 Stabilized APR2012 Page 3 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 4 of 12 Copyright SAE International Provided by IHS under license with SAE
12、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 5 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR20
13、12 Page 6 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 7 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproducti
14、on or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 8 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 9 of 12 Copyright S
15、AE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 10 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted
16、 without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 11 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1693 Stabilized APR2012 Page 12 of 12 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
