UNE 21-814-1992 Electrical apparatus for potentially explosive stmospheres General requirements《潜在爆炸性环境的电力材料 一般规则》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

JUS M A1 042-1980 Rougtiness comparisan specimens spark-eroded shot blasted and grit blasted and polished《粗糙对比样品，火花侵蚀和喷砂和抛光》.pdf

JUS M A1 043-1982 Roughness camparison specimens Gast surfaces《粗糙对比样品 盖斯特（Gast）表面》.pdf

JUS M A1 245-1978 Tolerances in mechanical engineering Tolerances ofform and ofposithn Maximum materiniprinciple《机械工程公差 形式及位置误差 最大计量原则》.pdf

JUS M A1 246-1978 Tolerances in mechanical engineering Tolerances of form and of position Practical axamples of indications on drawings《机械工程公差 形式及位置误差 图示实例》.pdf

JUS M A1 247-1978 Tolerances in mechanical engineering Tokrances ofform and position Drmensioning ofprofiles《机械工程公差 形式及位置误差 外形轮廓》.pdf

JUS M A1 248-1994 Tolerancing of form and orientation - verification principles and methods - Guidelines《形式及位置误差 确认原则及方法 指导》.pdf

JUS M A1 310-1983 VVorkshop gauges and referenca gauges for lain parts Determinations ofmeasures and admissible wear《莱恩（lain）部件车间计量器及参照计量器 指标及容许磨损测定》.pdf

JUS M A1 320-1983 VVorkshop gauges and reference gauges for lain parts Limit values of deviations and admissible wear for ex ternal measures《莱恩（lain）部件车间计量器及参照计量器 外部测量的限制阀偏差及容许磨损》.pdf

JUS M A1 340-1983 Workshop gauges and references gauges for lain parts Limit values of deviations and admissible wear for interna! measuras《莱恩（lain）部件车间计量器及参照计量器 内部测量的限制阀偏差及容许磨损》.pdf