1、Designation: F1018 87a (Reapproved 2010)An American National StandardStandard Specification forSteel Emergency Gear Stowage Locker1This standard is issued under the fixed designation F1018; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev
2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, material, andmanufacture of steel emergency gear stowage lock
3、ers.1.2 Emergency gear lockers shall be of four types (seeSection 3).1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA276
4、Specification for Stainless Steel Bars and ShapesA366/A366M Specification for Commercial Steel (CS)Sheet, Carbon (0.15 Maximum Percent) Cold-Rolled3A513 Specification for Electric-Resistance-Welded Carbonand Alloy Steel Mechanical TubingA563 Specification for Carbon and Alloy Steel NutsB36/B36M Spec
5、ification for Brass Plate, Sheet, Strip, AndRolled BarB124/B124M Specification for Copper and Copper AlloyForging Rod, Bar, and ShapesB176 Specification for Copper-Alloy Die Castings2.2 ANSI Standards:4ANSI B18.1.1 Small Solid RivetsANSI B18.6.3 Slotted and Recessed Head Machine Screwsand Machine Sc
6、rew NutsANSI B18.21.1 Lock WashersANSI B27.2 Plain Washers2.3 Other Documents:ABS Rules for Building and Classing Steel Vessels5SSPC Specification 66AWS D1.1 Welding Code73. Classification3.1 Emergency gear lockers shall be classified in four typesas follows:3.1.1 Type 1For stowage of one complete f
7、iremans outfit,conforming to all requirements of all sections, figures, anddetails of this specification.3.1.2 Type 2For stowage of two complete firemensoutfits, conforming to all requirements of all sections, figures,and details of this specification.3.1.3 Type 3For stowage of one complete firemans
8、 outfit,with locker dimensions in accordance with Figs. 2, 3, and 4(dimensions only), and conforming to the requirements of 3.2,3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.3.1.4 Type 4For stowage of two complete firemensoutfits, with locker dimensions in accordance with Figs. 2, 3,and 4 (dimensi
9、ons only), and conforming to the requirementsof 3.2, 3.3, 4.1, 5.2.4, and Sections 6 and 7 inclusive.3.2 One complete firemans outfit shall consist of thefollowing emergency gear (not included in this specification):3.2.1 Self-contained breathing apparatus (24 by 14 by 11 in.(610 by 355 by 280 mm).3
10、.2.2 Recharge air tank (7-in. (180-mm) diameter by 22 in.(560 mm) long).3.2.3 Set protective clothing, including helmet, gloves, andboots.3.2.4 Lifeline (150 ft (45 m), 18 by 18 by 10 in. (455 by 455by 255 mm).3.2.5 Three-cell, explosion-proof flashlight with spare cells.3.2.6 Flame safety lamp.3.2.
11、7 Fire axe.3.3 In addition to the equipment listed in 3.2, each lockershall contain space for the following (not part of this specifi-cation):1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOu
12、tfitting and Deck Machinery.Current edition approved May 1, 2010. Published June 2010. Originallyapproved in 1986. Last previous edition approved in 2004 as F1018 87a (2004).DOI: 10.1520/F1018-87AR10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Servic
13、e at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.4Available from American National Standards Institute (ANSI), 25 W
14、. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/www.eagle.org.6Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,Pittsburgh, PA 15222-4656, http:/www.s
15、spc.org.7Available from American Welding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126, http:/www.aws.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.3.1 First-aid kit, (1), (10 by 10 by 7 in. (255 by 255 by 180mm).3.3.2 Sp
16、are air tanks, as space allows (see Figs. 2, 3, and 4.).4. Ordering Information4.1 Order using this ASTM designation, year of issue,locker type, and finish.5. Materials and Manufacture5.1 MaterialsMaterials shall be as specified in Table 1.5.2 Manufacture:5.2.1 Mandatory dimensions and construction
17、details forTypes 1 and 2 are as depicted in Figs. 1-9.5.2.2 Mandatory dimensions for Types 3 and 4 are as shownin Fig. 2, Fig. 3, and Fig. 5, respectively, and applicable detailsof Sections “A-A and “B-B.Alternative construction detailsare permissible.5.2.3 Construction details depicted in Figs. 4-9
18、, while spe-cifically referring to locker Type 2, shall be adapted to suitlocker Type 1.5.2.4 Welded construction, in accordance with ABS Rulesfor Building and Classing Steel Vessels or AWS D1.1 Struc-tural Welding Code shall be used throughout, unless otherwisespecified.6. Dimensions and Tolerances
19、6.1 Dimensions are as indicated.6.2 Tolerance6116 in. (1.5 mm).7. Workmanship, Finish and Appearance7.1 Entire assembly shall be free of weld spatter, slag,splinters, sharp edges, burrs, projections, and other defects thatmay be hazardous to personnel.7.2 The locker shall be cleaned after assembly t
20、o a com-mercial finish in accordance with SSPC Specification 6.7.3 Unless otherwise required by the ordering documents,the unit shall have the manufacturers standard baked-onenamel finish.7.3.1 The color shall be specified in the ordering documents.8. Keywords8.1 emergency gear; firemans locker; fir
21、emans outfit;locker; steel locker; stowage lockerF1018 87a (2010)2TABLE 1 Parts List for Locker Type 2NOTE 11 in. = 25.4 mm.DescriptionItemNumberQuantityASTM, ANSIDocumentsLocker top sheet, 16 gage 3 39 in. long 3 30 in. wide, carbon steel 1 1 A366/A366MLocker side, right sheet, 16 gage 3 72 in. lon
22、g 3 2958 in. wide, carbonsteel21 A366/A366MLocker side, left sheet, 16 gage 3 72 in. long 3 2958 in. wide, carbonsteel31 A366/A366MLocker back sheet, 16 gage 3 72 in. long 3 39 in. wide, carbonsteel41 A366/A366MLocker bottom sheet, 16 gage 3 42 in. long 3 31 in. wide, carbon steel 5 1 A366/A366MDoor
23、, right sheet, 16 gage 3 73 in. long 3 25 in. wide, carbon steel 6 1 A366/A366MDoor, left sheet, 16 gage 3 73 in. long 3 23 in. wide, carbon steel 7 1 A366/A366MShelf, full-width sheet, 16 gage 3 40 in. long 3 26 in. wide, carbon steel 8 2 A366/A366MShelf, half-width sheet, 16 gage 3 26 in. long 3 2
24、1 in. wide, carbon steel 9 2 A366/A366MPartition, vertical sheet, 16 gage 3 52 in. long 3 25 in. wide, carbon steel 10 1 A366/A366MCorner bracket sheet, 16 gage 3 5 in. long 3 334 in. wide, carbonsteel11 4 A366/A366MLever handle, rightdoorcast brass 12 1 B176 (UNS C8650)Keeper brass 13 1 B124/B124M
25、(UNS C6750)Machine screw oval-head, #10-24 UNC-2A 3 length to suit brass 14 14 ANSI B18.6.3B124/B124M (UNS C6750)Nut hexagon machine, #10-24 UNC-2B 15 14 ANSI B18.6.3brass B124/B124M (UNS C6750)Escutcheon sheet, 16 gage 3 2 in. long 3 138 in. wide, brass 16 1 B36/B36MLocking rod, upper round bar,516
26、-in. diameter 3 37 in. long, carbon steel 17 1 A36/A36MLock rod, lower round bar,516-in. diameter 3 37 in. long, carbon steel 18 1 A36/A36MGuide, locking rod tube, -in. outside diameter 3 0.065-in. wall thickness 3118-in. long, carbon steel19 2 A513Latch sheet, 12 gage 3 31116 in. long 3 2 in. wide,
27、 carbonsteel20 1 A366/A366MReinforcing, latch sheet, 16 gage 3 5 in. long 3 134 in. wide, carbon steel 21 1 A366/A366MLock washer38-in. nominal size, carbon steel 22 1 ANSI B18.21.1Rivet brazier head,532-in. diameter 23 2 ANSI B18.1.1Rivet flathead,316-in. diameter 24 2 ANSI B 18.1.1Insulation wool
28、felt,364 in. thick 3 2 in. long 3 138 in. wide 25 1Reinforcing clip sheet, 12 gage 3 1 in. square, carbon steel 26 1 A366/A366MReinforcing clip sheet, 16 gage 3 1 in. square, carbon steel 27 1 A366/A366MCam sheet, 12 gage 3 178 in. square, carbon steel 28 1 A366/A366MLatch filler sheet, 16 gage 3 27
29、8 in. long 3 2 in. wide, carbonsteel29 1 A366/A366MStrap sheet, 16 gage 3 2 in. long 3 1 in. wide, carbon steel 30 1 A366/A366MNut hexagon,38-16 UNC-2B, carbon steel 31 1 A563Liner sheet, 16 gage 3 1 in. long 3 118 in. wide, carbonsteel32 1 A366/A366MHinge sheet, 16 gage 3 3 in. long 3 1 in. wide, c
30、arbon steelincluded:316-in. diameter 3 1-in. long stainless steelpin33 6 A366/A366MA276Lock washer316-in. nominal size,716-in. outside diameter, carbonsteel34 12 ANSI B18.21.1Liner, hinge sheet, 16 gage 3 2 in. long 334 in. wide, carbon steel 35 6 A366/A366MLeg angle, 1 3 1 318 3 6 in. long, carbon
31、steel 36 4 A36/A36MFoot pad sheet, 10 gage 3 1 in. square, carbon steel 37 4 A366/A366MLeg bracket sheet, 10 gage 3 8 in. long 3 3 in. wide, carbon steel 38 4 A366/A366MLeg reinforcement sheet, 10 gage 3 8 in. long 3 134 in. widebend toform78- 378-in. angle, carbon steel39 4 A366/A366MMachine screw
32、-2OUNC-2A 334 in. long, carbon steel 40 16 ANSI B18.6.3Nut hexagon machine, -2OUNC-2B, carbon steel 41 16 ANSI B18.6.3Lock washer -in. nominal size, carbon steel 42 16 ANSI B18.21.1F1018 87a (2010)3NOTE 11 in. = 25.4 mm.NOTE 2Approximately 2-in. high red lettering typical.FIG. 1 Emergency Gear Stowa
33、ge LockerType 1F1018 87a (2010)4NOTE 11 in. = 25.4 mm.NOTE 2Approximately 2-in. high red lettering typical.FIG. 2 Emergency Gear Stowage LockerTypes 2, 3, and 4F1018 87a (2010)5FIG. 3 Emergency Gear Stowage LockerTypes 2, 3, and 4 (Section “A-A”)F1018 87a (2010)6NOTE 11 in. = 25.4 mm.FIG. 4 CornerF1
34、018 87a (2010)7NOTE 11 in. = 25.4 mm.FIG. 5 Lock BoltF1018 87a (2010)8NOTE 11 in. = 25.4 mm.FIG. 6 Locking HandleF1018 87a (2010)9NOTE 11 in. = 25.4 mm.FIG. 7 LatchMiscellaneous DetailsF1018 87a (2010)10NOTE 11 in. = 25.4 mm.FIG. 8 LegF1018 87a (2010)11NOTE 11 in. = 25.4 mm.FIG. 9 Hinge and LinerAST
35、M International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are en
36、tirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsa
37、nd should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee
38、on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1018 87a (2010)12
